Med835dw3 Parts

This is a metal flange bracket that secures the heater housing assembly inside the dryer. It holds the heater box in the proper position to ensure safe and efficient heat distribution during drying cycles. Replace this bracket if it is bent, corroded, or broken, which can cause the heater housing to shift and lead to overheating or unusual noises.

Structural inner panel that supports the dryer tub and provides mounting for controls and seals. Replace if cracked or damaged to prevent leaks. Verify fit.

Internal wire harness assembly that connects dryer components for signal and power flow. Replace if wires are cracked, frayed, or connectors are damaged.

Exposed wiring at the back of your dryer? This terminal block cover shields electrical connections from accidental contact and debris. Simple snap-on install.

Front control panel for dryers. Restores user interface and cosmetic cover. Replaces cracked, faded, or damaged panels to restore button access.

This cable tie secures wiring and the power cord to the appliance chassis to help prevent chafing, pinching, or loose connections. Simple, low-cost part that restores proper wire routing and strain relief. What it does

• Holds wiring and harnesses in place to prevent rubbing against sharp edges
• Helps reduce risk of intermittent power or connector strain caused by loose wires
• Keeps harnesses routed for correct clearance and component access
• Useful during repairs to restore original wire routing and strain relief

• One cable tie (wire harness retainer)

• Safety first: disconnect the appliance from power before inspecting or replacing wiring components
• Remove the damaged or existing retainer and route harnesses to match original OEM routing before installing the new tie
• Trim excess tie tail; do not overtighten—secure, but avoid crushing wires
• Replace any tie that's melted, cracked, or otherwise damaged rather than reusing it

Exhaust vent elbow routes hot air and lint from your dryer to the external vent. Replace if cracked, bent, or leaking to restore airflow and safety.

If your dryer takes forever to dry clothes or feels overly hot, a clogged or damaged exhaust pipe may be restricting airflow. Direct replacement part.

Sound absorber insulation pad for dryers. Installs inside cabinet to dampen noise and vibration. Replace if torn, compressed, or missing.

Dryer seal that prevents air leaks and maintains proper airflow. Replace if you notice excessive lint buildup or reduced drying efficiency. Verify fit with your model number before ordering.

This is a foam seal that fits along the control panel area of a dryer, creating a barrier against moisture, lint, and air leaks. It helps protect internal control components from heat and debris. Replace this seal if it is cracked, compressed, or missing, which can allow lint buildup near controls or cause air leaks that reduce drying efficiency.

Fixes dryer that won't start or hums but doesn't spin. This run capacitor provides the motor boost needed to turn the drum. Moderate 30-minute repair.

This replacement dryer drum is the rotating tub that holds and tumbles clothes while channeling airflow for even drying. Swap a damaged drum to stop rubbing noises, fabric snags, and uneven tumbling. What it does:

• Rotates inside the dryer cabinet to tumble laundry and direct hot air through the load.
• Supports the drum belt and rides on rollers/glides for smooth operation.
• Replace when you see dents, cracks, deep gouges, or metal-to-metal contact.
• Common symptoms of a failing drum: scraping or grinding noises, clothes catching, visible drum damage, or uneven tumbling.
• Inspect rollers, glides, and belt when replacing the drum.

• Disconnect power (and turn off gas supply for gas dryers) before beginning any repairs.
• Support the drum when removing or installing to avoid dropping or damaging the cabinet or finish.
• Installation typically requires removing the dryer front or top panels and repositioning the belt and rollers; have basic hand tools ready.
• If you hear persistent noises after install, recheck belt alignment, roller condition, and cabinet mounting.

Replacement trim panel for your dryer. Installs on the cabinet to cover edges and gaps. Order a new one if your original is cracked, chipped, or missing.

Mounting bracket for dryer assembly. Secures components in place during operation. Replace if bracket is bent, cracked, broken, or missing hardware.

Rear access panel for dryers. Covers the back of the cabinet and provides access to internal components. Replace if cracked, dented, or missing.