Med835dw3 Parts

This small nozzle directs the water stream cleanly into the ice maker during the fill cycle, helping prevent splashing and leaks so your unit produces consistent, properly sized ice cubes.

• Channels water from the fill tube into the ice maker's fill cup/mold
• Helps maintain correct fill volume and cube formation
• Reduces stray spray that can cause frost or ice buildup
• Typical symptoms: dripping from the fill tube, ice clumps below the ice maker, hollow/small cubes, or water on the freezer shelf

• Disconnect power and shut off the water supply before servicing
• Access the fill tube/ice maker area and remove the old nozzle
• Match the original orientation and seat the new nozzle fully
• Restore water and power, then run a fill cycle and check for leaks

This replacement seal restores a tight barrier between mating parts in your appliance to help prevent leaks and keep moisture and air where they belong. Replacing a worn seal helps maintain proper performance and reduce messes.

• Forms a tight, reliable barrier between components
• Helps stop drips, seepage, and moisture wicking at the joint
• Replace if the old seal is cracked, flattened, swollen, or brittle
• Common symptoms include small puddles, dampness around the connection, or musty odors

• Disconnect power and shut off the water supply before servicing
• Note the seal's orientation; remove the old seal and clean mating surfaces of residue or mineral buildup
• Apply a light coat of food-grade silicone to ease installation
• Seat the new seal evenly without twisting; reassemble and check for leaks during initial operation

The Valve is an OEM part for Whirlpool dryers. It is responsible for controlling the flow of water into the dryer's steam generator, enabling the steam function during the drying cycle.

A bad water inlet valve can occur due to wear and tear, sediment buildup, or malfunctioning internal components. If you notice symptoms such as no steam being produced during the drying cycle, insufficient steam generation, or water leakage around the valve, it may be time to replace this part.

Symptoms of a bad valve include:

• No steam being produced during the drying cycle
• Insufficient steam generation
• Water leakage around the valve

Restore your Whirlpool dryer by replacing the faulty or damaged steam water inlet valve with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This factory fastener secures appliance components and panels, helping keep assemblies properly aligned and tight. Replace worn, stripped, or missing hardware to eliminate looseness and vibration and maintain safe, reliable operation.

• Fastens brackets, panels, trim, and internal assemblies to the cabinet/frame
• Helps maintain alignment of doors, consoles, or covers
• Restores a tight fit to reduce rattling, vibration, or shifting
• Common symptoms: missing screw, stripped head/threads, loose panel or handle, recurring vibration/noise

• Disconnect power (and shut off gas/water if applicable) before servicing
• Match thread and length to the original fastener for proper fit
• Start threading by hand to avoid cross-threading; use the correct driver
• Do not overtighten into plastic or thin sheet metal

This strike is the latch receiver the door or lid engages when closed. Replacing a worn or broken strike restores a secure close and ensures the control correctly senses a closed door so cycles can run. What it does:

• Provides the fixed catch point for the latch mechanism
• Keeps the door/lid closed and properly aligned during operation
• Works with the interlock/switch to signal that the door/lid is closed
• Common symptoms: door won't latch or pops open, "door/lid open" message, cycle won't start, visible damage to the strike

• 1 strike

• Disconnect electrical power to the appliance; shut off water if applicable
• Open the door/lid and remove the original strike (typically secured by screws or retaining tabs)
• Position and secure the new strike, reusing original hardware; tighten snugly without over-tightening
• Close and open the door/lid to confirm smooth latch engagement and alignment; adjust if needed

This Heater Box Bracket secures the dryer's heater housing to the cabinet, keeping the heating assembly firmly mounted and aligned. Replace a bent, cracked, or missing bracket to restore stable support and reduce vibration around the heater area.

• Anchors the heater housing/box to the cabinet frame
• Maintains proper alignment and clearance for the heating element assembly
• Helps prevent rattling or rubbing noises from a loose heater housing
• A damaged bracket may leave the heater housing loose, cause vibration, or contribute to intermittent heating issues

• Disconnect power; if gas, shut off gas supply and allow the unit to cool completely
• Access the heater housing; note bracket orientation and reuse existing fasteners
• Support the heater housing and keep wiring clear while removing/installing the bracket
• After installation, verify the housing sits square and clear of the drum and wiring before restoring power

This is the appliance's cabinet top panel in a chrome finish. It replaces a dented, bent, or rusted top to restore a clean appearance and a secure fit while protecting internal components and supporting mounted parts.

• Forms the finished top surface of the cabinet (chrome finish)
• Shields internal components from debris and accidental contact
• Provides mounting/support points for the console, hinges, or brackets (varies by model)
• Addresses damage, corrosion, looseness, or rattling from a bent or missing top

• Disconnect power before servicing; wear cut-resistant gloves (sheet-metal edges are sharp)
• Retain and reuse the original screws/clips; transfer any brackets from the old panel
• Fasteners are typically at the rear or beneath the console—support the panel, remove screws, then lift off
• Align the new panel and tighten fasteners evenly to ensure a secure, rattle-free fit

This elbow is a molded hose connector that redirects fluid or airflow in the appliance, restoring proper routing for drainage or vent lines. It helps stop leaks and maintains correct hose alignment for reliable operation. What it does

• Redirects hose or duct routing at an angle to fit tight spaces
• Restores a secure connection where a cracked or broken elbow causes leaks
• Helps prevent kinks or pinched hoses that can cause poor drainage or reduced airflow
• Supports proper sealing when used with the correct clamps or gaskets

• One elbow connector

• Disconnect power and shut off water before replacing the part
• Inspect mating hose ends and clamps; replace damaged hoses or clamps for a secure seal
• Ensure correct orientation and fully seat the elbow before tightening clamps
• Do not force the part into place; confirm fit and alignment to avoid stress or leaks

The Hinge is an OEM part for Whirlpool electric dryers. Located on the dryer door frame, this heavy-duty metal hinge securely holds the weight of the swinging door panel. It allows for easy opening, closing, and latching of the dryer entrance through thousands of cycles. 

Causes of a faulty hinge can include wear from years of operation putting pressure on the internal bearing as the door is repeatedly swung open and shut. Accidental impacts could also bend or damage hinge components over time.

Symptoms of a bad hinge include:

• Squeaking or grinding noises coming from the hinge area  
• Increased effort needed to open or close the door
• The door sagging when open or not staying still when closed
• Difficulty centering or aligning the door seal 

This Whirlpool dryer hinge is also compatible with brands including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This replacement air duct channels and directs airflow inside the appliance to help maintain balanced temperatures. Replacing a cracked, warped, or missing duct restores proper air circulation and helps the unit cool more consistently. What it does

• Routes air through internal passages between compartments
• Helps maintain consistent temperatures by preventing leaks and bypasses
• Restores designed airflow when the original duct is damaged or missing
• Common symptoms include uneven cooling, warm spots, frost or moisture buildup, or unusual airflow noise

• 1 air duct

• Disconnect power before servicing; wear cut-resistant gloves around sharp panels
• Remove shelves/panels as needed to access the duct and retain all fasteners
• Transfer any foam seals or gaskets from the original part
• Ensure the duct seats fully and fasteners are snug to prevent air leaks

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Replacement bumper that cushions appliance parts and absorbs shock to prevent rubbing, rattling and surface damage. Restores proper fit and quieter operation for components that contact cabinets, doors or panels. What it does:

• Cushions contact points to reduce noise from doors, drawers or panels.
• Prevents metal-to-metal or metal-to-surface scraping that can cause wear or cosmetic damage.
• Helps components close and seat more evenly to reduce vibration and movement.
• Common symptom fixes: eliminates rattling, stops rubbing noises, and prevents chipping or scuffing where parts meet.

• One bumper.

• High-level, tool-light replacement; usually presses into or adheres to the mounting surface.
• Disconnect power or unplug the appliance before opening panels where required.
• Inspect surrounding clips/retainers and clean the mounting area for best adhesion or fit.

This bezel is the small trim ring that finishes and protects a control opening on your appliance. It helps center the control and restores a clean, factory look when the original trim is cracked or missing.

• Centers and supports a control knob or selector shaft
• Covers the raw panel opening to keep out debris
• Helps maintain proper knob alignment and feel
• Common signs it's needed: cracked or missing trim, loose/wobbly knob, uneven alignment, cosmetic damage

• Disconnect power to the appliance; also shut off gas before servicing
• Pull off the control knob, then remove the old bezel (release tabs or screws as designed)
• Note orientation; seat the new bezel fully and reinstall the knob
• Test control operation before returning the unit to service

This replacement door seal restores a tight door-to-cabinet gasket to stop leaks and help the appliance operate reliably. It replaces worn, cracked, or torn seals so doors close securely and minimize water, air, and odor escape. What it does:

• Creates a secure seal between the door and cabinet to prevent water or air leaks.
• Helps reduce odors and protects internal components from moisture damage.
• Restores proper door closure to prevent puddles, drips, or inefficient operation.
• Commonly replaced when the existing seal is torn, stretched, or compressed.

• Disconnect power and water before starting; follow all safety precautions.
• Remove the old seal and clean the mounting surface before installing the new gasket to ensure a proper fit.
• Seat the gasket evenly into the door channel and verify the door closes fully with no gaps.
• After installation, run a short test cycle or inspection to confirm there are no leaks.

This air duct directs airflow inside the appliance to help maintain proper ventilation and cooling. Replacing a damaged duct restores correct air movement and can reduce noise or uneven temperature issues. What it does:

• Channels warm or cool air through the appliance's ventilation path
• Prevents air leaks that can cause unusual noises or reduced performance
• Helps maintain consistent internal temperatures and component cooling
• Supports connected seals and ducts to ensure efficient airflow

• Disconnect power before servicing to avoid shock or injury
• Inspect surrounding seals and fasteners; replace any that are worn or broken
• Handle carefully to avoid cracking plastic tabs during removal/installation