Mlg20pcrww2 Parts

This high-limit thermostat helps stop overheating by opening the heater circuit at preset temperatures, protecting the appliance and improving safety. Replace a failed thermostat to restore proper over-temperature shutoff. What it does:

• Opens the heating circuit at its rated temperature to prevent excessive heat buildup
• Stops the heater from running if the appliance overheats
• Common symptoms: appliance overheating, no heating or intermittent heating, or heat cycling off unexpectedly
• Used as a safety cutoff in the appliance's heating system

• Disconnect power before inspecting or replacing the thermostat
• Handle terminals carefully and note wiring locations for correct reassembly
• Verify operation only after proper installation and restoring power

This electrical connector links wiring within the appliance's harness, restoring a secure, reliable connection for proper operation. Use it to replace a damaged or corroded connector that's causing intermittent power or component failures.

• Creates a solid electrical connection between harness leads
• Helps resolve issues like intermittent operation, no power to a component, or visible heat damage at a connection point
• Maintains correct current flow and reduces risk of arcing at loose terminals
• Designed to fit the specified harness location per model

• Disconnect power and shut off utilities before servicing
• Match wire colors/positions and transfer one lead at a time to avoid miswiring
• Ensure terminals are fully seated and the connection is snug
• Inspect surrounding wiring for heat damage or corrosion and address as needed

The Water Level Pressure Switch is an OEM replacement part for Whirlpool washing machines. It monitors the water level in the washer tub and senses pressure changes, signaling when to stop or start water filling. 

Causes of a faulty switch can include mineral buildup interfering with sensor operation over time. Failure symptoms include:

• Inability to start or stop water filling 
• Too much or too little water entering the tub
• Delays in cycle progress or termination of cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Coin Drop Assembly is an OEM replacement part for Whirlpool washers. It allows users to insert coins and activate the machine on commercial or coin-operated washers.

A bad coin drop assembly can be caused by wear and tear over time or damage due to excessive use or mishandling. If you notice issues such as the coin mechanism not working, coins getting stuck, or the machine not starting when coins are inserted, it may be time to replace the coin drop assembly.

Symptoms of a faulty coin drop assembly include:

• Coins not being accepted or not registering
• Coins getting jammed or stuck in the mechanism
• Inability to start the washer with the coin insertion

Restore the function of your Whirlpool commercial washer by replacing the old or damaged coin drop assembly with this genuine OEM part.

This part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This dispenser handle cover attaches to the front of the dispenser assembly, providing the finished surface you press or pull and protecting internal components. Replacing a cracked or missing cover restores clean appearance and reliable, comfortable operation.

• Provides the user-facing surface for operating the dispenser
• Covers and helps protect the internal lever/switch area
• Restores proper feel and alignment of the actuator
• Common symptoms: cracked/broken cover, loose or missing handle, sticking or hard-to-use dispenser, cosmetic wear

• Disconnect power to the appliance; shut off water supply if working near water connections
• Access the dispenser area; release retaining tabs or screws and carefully remove the old cover
• Align the new cover and snap or fasten it into place without overflexing the tabs
• The actuator/drawer moves freely before restoring power

This door seal is the refrigerator door gasket that helps maintain a tight seal to keep cold air in and reduce energy loss. Replacing a worn or torn gasket helps the appliance cool efficiently and protect stored food. What it does

• Forms an airtight barrier around the refrigerator door to prevent warm air from entering
• Helps maintain consistent internal temperature and efficient operation
• Reduces frost buildup and cycling caused by a leaking seal
• Commonly shows symptoms like visible cracks, tears, flattening, or a door that won't close snugly

• One refrigerator door gasket

• Inspect the door frame and strike surfaces; clean mounting channel before installing the new gasket
• Warm the gasket slightly or use recommended installation tools to ease fitting into the channel
• Check alignment and closure after installation; replace if mounting clips or retainer are damaged
• Disconnect power only if required by your model and follow all safety precautions

This replacement cover restores the appliance's exterior finish while protecting internal components from dust and debris. It fits into the cabinet opening to secure and conceal underlying parts for safe, clean operation. What it does:

• Protects internal components and wiring from dust, lint, and accidental contact
• Restores a finished appearance when a panel is cracked, warped, or missing
• Prevents small items from falling into the appliance cavity
• Reduces rattling from loose or missing panels

• One replacement cover

• Disconnect power (and water if applicable) before starting any repair
• Basic hand tools (screwdriver) may be required to remove fasteners or retainers
• Align tabs or slots, then secure fasteners without overtightening to avoid cracking

This is the outer trim ring for a front-load washer door that restores the door's appearance and secures the outer edge of the door assembly. Ideal for replacing cracked, chipped or faded outer trim to make the door look and fit like new. What it does:

• Replaces a cracked, chipped or damaged outer door trim that exposes the door edge or looks worn
• Secures the outer edge of the door assembly and helps hold the door glass and inner components in place
• Restores a clean, finished appearance to the washer door
• Can help ensure the outer trim sits flush so the door closes and seals properly when reassembled

• Disconnect power to the appliance before starting and work with the door in a stable position
• Remove the washer door or inner trim per factory instructions; handle door glass carefully to avoid breakage
• Reuse original screws/clips unless damaged; align trim evenly before tightening

This replacement commercial door restores a secure, smooth-closing entry to your appliance. Use it to replace a cracked, bent, or damaged door to maintain proper closure, alignment, and appearance so the unit functions as intended.

• Functions as the appliance's front door, providing access for loading/unloading
• Interfaces with hinges and latch/strike for smooth operation and secure closure
• Presents the proper contact surface for the seal or interlock area, where applicable
• Typical symptoms: door cracked, warped, or loose; won't close or latch; misaligned or rubbing

• Disconnect power; if the unit connects to gas or water, shut those off before service
• Support the door while removing hinge and latch/strike fasteners to avoid cabinet damage
• Transfer any reusable hardware, trim, or nameplates from the old door to the new one
• After installation, verify alignment and latch engagement; adjust hinges/strike for an even seal

A duct collar that connects and secures the dryer's exhaust duct to the appliance, helping channel hot, moist air safely out of the dryer. Replaces a damaged or loose collar to restore a tight vent connection. What it does

• Provides a secure connection point between the dryer and the exhaust duct to help direct airflow out of the appliance.
• Helps reduce vent leaks that can cause poor drying performance or excess lint buildup in the cabinet/closet.
• Restores proper duct alignment to reduce rattling or vibration from a loose duct connection.
• Used when the existing collar is cracked, bent, corroded, or no longer holds the duct firmly.

• One duct collar.

• Always disconnect electrical power before servicing the dryer.
• Clean lint from the vent path before installing the new collar to ensure good airflow and reduce fire risk.
• Installation typically requires basic hand tools and a clamp or screws to secure the duct; follow the dryer's service instructions.