Msbr415s Magicchef Parts

Lower front grille that covers the base opening of your refrigerator. Replace if cracked, broken, or missing to restore a finished look.

Crisper drawer won't adjust humidity or slide is broken? This humidity control slide mounts in the crisper cover to regulate airflow and moisture levels.

Plastic tray that installs below the ice and water dispenser to catch spills and drips. Replace if cracked, broken, or missing to prevent leaks.

Supports and pivots your refrigerator door for smooth opening and flush closing. Replace if hinge is worn, damaged, or causing misalignment issues.

Right-angle elbow that connects the water supply line to the icemaker fill tube. Replace if cracked, leaking, or broken to restore a sealed connection.

Molded plastic drawer for freezer compartment. Replace if cracked, warped, or broken to restore smooth sliding and keep frozen items organized.

Mounting clip that secures internal panels and trim in your refrigerator. Replaces broken, cracked, or missing retainers that cause loose or rattling parts.

This replacement lid fits the refrigerator utility/bin drawer and restores a secure cover to keep stored items contained and organized. It replaces cracked, broken or warped lids so the bin functions as intended. What it does:

• Covers and protects items stored in the utility/bin drawer
• Replaces lids that are cracked, chipped or no longer latch properly
• Helps prevent items from shifting or falling into other compartments
• Restores a proper seal and alignment of the utility/bin cover

• Unplug or disconnect power to the appliance before servicing for safety
• Remove the bin/drawer per the manufacturer instructions to access the lid
• Align hinge tabs or mounting points and snap or fasten the lid into place
• Handle carefully; plastic edges or mounting points can be fragile during installation

Replace a worn, broken, or missing refrigerator drawer slide. Restores smooth gliding and proper alignment for drawers. Essential for secure operation.

This component allows the refrigerator door to pivot smoothly and maintains proper door alignment, located within the door hinge assembly. Replace it when the door doesn't close properly, appears misaligned, or makes grinding noises when opening or closing.

The lower hinge closing cam assists in the smooth closing action of the refrigerator door and helps maintain proper door alignment. Located within the bottom door hinge assembly, it should be replaced when the door doesn't close properly, swings open on its own, or requires excessive force to close.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

Rubber grommet kit that mounts and cushions the compressor. Replace worn, cracked, or damaged grommets to restore proper support and isolation.

This sachet holder housing assembly secures single-use detergent or cleaning sachets inside the dispenser so they stay in place and release correctly during cycles. Replacing a cracked or broken holder restores reliable sachet positioning and dispensing. What it does:

• Holds detergent/cleaning sachets in the dispenser so they don't shift or drop into the tub.
• Ensures sachets stay aligned for proper release during the wash or cleaning cycle.
• Helps prevent sachets from rupturing or blocking the dispenser area.
• Common symptoms of a bad holder: sachets falling out, sachets not dispensing properly, or poor wash/cleaning results.

• Disconnect power (and water, if required) before servicing the dispenser area.
• Access the dispenser per the owner's manual; the holder typically snaps into place or secures with a small fastener.
• Handle plastic clips and tabs gently to avoid breakage; use a non-marring pry tool if needed.

Main wire harness that routes power between the control board and components. Replace if wiring is damaged, burned, or connector clips are broken.

Ice cubes stuck in tray and won't eject? This ejector arm pushes ice from the mold into the bin. Simple snap-in install restores ice production.