Msd245fr Parts

Replaces cracked, broken, or missing egg tray in your refrigerator door. Molded holder keeps eggs organized and secure to prevent rolling and breakage.

This genuine replacement screw secures appliance panels and trim so covers, consoles, and components stay firmly in place for safe, quiet operation. It replaces worn or missing fasteners to restore proper fit and reduce vibration and rattling. What it does:

• Secures control panels, trim pieces, or access panels to the appliance frame
• Keeps panels aligned to prevent gaps and light leaks
• Reduces vibration-related noise from loose panels or components
• Helps maintain safe operation by keeping covers and guards properly attached

• The replacement screw shown/listed

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start the screw by hand to ensure proper thread engagement, then tighten securely but do not overtighten

Replacement mounting screw for securing freezer panels, brackets, and components. Restores proper fastening where original screw is missing, stripped, or damaged.

Size: 8-32 x 1/4 inch.

Size: 8-32 x .312 inch.

Freezer not cooling or fan not running? This evaporator fan motor circulates cold air across coils to maintain even temperatures. DIY-friendly repair.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

This seal strip replaces a worn or damaged door gasket edge to restore a proper seal and help the appliance maintain temperature and operate quietly. It's a direct-fit service part used where a continuous seal is required. What it does:

• Provides a flexible barrier along the door/frame to reduce air leaks and heat/cold loss
• Helps prevent moisture buildup and improves energy efficiency when sealing is restored
• Reduces rattling and vibration caused by a compressed or torn seal edge
• Commonly replaced when the strip is torn, missing, or no longer adheres properly

• One seal strip

• Disconnect power to the appliance before servicing to avoid electrical or burn hazards
• Clean and dry the mounting surface; remove old adhesive or residue for best adhesion
• Align the strip carefully and press firmly; allow any adhesive to cure per manufacturer instructions

Refrigerator air return cover assembly snaps into the back wall to direct airflow and protect the return opening. Replace if cracked, broken, or missing.

This knurled pin secures the juicer cone and helps transmit torque for proper juicing action. It replaces a worn or damaged roll pin to restore stable cone alignment and smooth operation. What it does:

• Secures the juicer cone or attachment to the drive shaft to prevent slipping
• Transfers rotational force from the motor to the juicer cone
• Helps stop wobble, misalignment, or intermittent engagement of the juicer cone
• Commonly replaced when the pin is bent, worn, or broken

• One knurled pin

• Turn off and unplug the appliance before servicing to avoid shock or injury
• Remove the juicer cone and any retaining parts per the service diagram before replacing the pin
• Use appropriate hand tools; avoid excessive force which can damage the shaft or housing

Replacement hex nut secures panels, trim, and brackets in refrigerators. Needed when original nut is worn, missing, or stripped, causing loose components.

Fix intermittent water leaks or flow issues from your dispenser with a new ball sleeve. This guide supports the valve ball for a proper seal.

Panel fastener screw for refrigerators and freezers. Secures cabinet panels, trim, and components. Replace if missing, stripped, or damaged.

Machine screw secures appliance panels, brackets, and internal components. Replace missing, stripped, or worn fasteners for reliable assembly.

Replacement screw for securing refrigerator panels, brackets, and components. Needed when original fasteners are missing, stripped, or damaged.