Msd2641feb Parts

6 - 19 x .250

Rubber grommet that cushions and secures the refrigerator condenser assembly. Replace if cracked, worn, or missing to reduce vibration and noise.

This is a discharge tube used in the refrigerator's sealed refrigeration system, connecting the compressor output to the condenser. It carries high-pressure refrigerant as part of the cooling cycle. Replace this tube if it shows signs of damage, kinking, or refrigerant leaks that cause the refrigerator to stop cooling properly.

Refrigerator not cooling properly? This 36-inch condenser coil removes heat from your fridge. Common fix for warm temps and overheating compressors.

This wire harness connects key internal components so power and signals are routed correctly. Replace a damaged harness to restore reliable operation when the original wiring is burned, brittle, cut, or causing intermittent electrical connection issues.

• Carries electrical power and control signals between designated components
• Restores dependable connections when wires or terminals are heat-damaged, broken, or corroded
• Helps address no-operation or intermittent operation of the affected component(s)
• Common clues include scorched insulation, loose/burned connectors, or visible wire damage

• Disconnect power before servicing; shut off gas/water if applicable
• Photograph/label connections and routing before removal
• Route and secure wiring exactly as original, away from sharp edges, hot surfaces, and moving parts; reuse existing clips/ties
• Seat connectors fully and avoid pulling on wires during removal/installation

Seals your freezer door to maintain cold temperatures and prevent frost buildup. Replace when worn, cracked, or loose to restore efficiency. Confirm fit with your model number.

This grommet isolates the refrigerator's fan motor from its mounting bracket to reduce vibration and noise while keeping the motor secure. Replacing worn or missing grommets helps stop rattles and prevents the fan blade from rubbing.

• Cushions the fan motor to maintain proper alignment and clearance
• Absorbs vibration to help reduce humming, buzzing, or rattling sounds
• Helps keep the motor stable so the blade doesn't contact the shroud
• Common signs of failure include excess vibration, noise, or a loose fan motor

• Disconnect power to the refrigerator before servicing
• Access the fan motor area (rear of unit or inside the freezer, depending on model) and support the motor
• Remove mounting hardware and seat the new grommet fully in the bracket/mount
• The fan blade spins freely with even clearance before reassembling and restoring power

Right-angle elbow that connects the water supply line to the icemaker fill tube. Replace if cracked, leaking, or broken to restore a sealed connection.

Fix warm fridge temps or frost buildup with a new door gasket. Restores airtight seal to prevent cooling loss. DIY install in 30-45 minutes.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

This white sump tray captures and channels dishwasher wash and drain water to the drain pump, helping prevent leaks and protect the tub assembly. It's a direct-replacement plastic tray used in the lower cavity. What it does:

• Collects and routes standing water to the drain pump to support normal drainage.
• Provides a mounting/containment area for the pump and related drain components.
• Helps prevent water from reaching electronic components and the cabinet floor.
• Commonly replaced when the tray cracks, warps, or is visibly leaking.

• Disconnect power and water supply before beginning any repair.
• Handle sharp sheet-metal edges inside the tub; wear gloves and eye protection.
• After reassembly, run a short cycle and check for proper drainage and leaks.

Ice cubes stuck in tray and won't eject? This ejector arm pushes ice from the mold into the bin. Simple snap-in install restores ice production.

Black plastic shim that supports and aligns the door hinge assembly. Replace if broken, cracked, or missing to restore proper door alignment.

This seal strip replaces a worn or damaged door gasket edge to restore a proper seal and help the appliance maintain temperature and operate quietly. It's a direct-fit service part used where a continuous seal is required. What it does:

• Provides a flexible barrier along the door/frame to reduce air leaks and heat/cold loss
• Helps prevent moisture buildup and improves energy efficiency when sealing is restored
• Reduces rattling and vibration caused by a compressed or torn seal edge
• Commonly replaced when the strip is torn, missing, or no longer adheres properly

• One seal strip

• Disconnect power to the appliance before servicing to avoid electrical or burn hazards
• Clean and dry the mounting surface; remove old adhesive or residue for best adhesion
• Align the strip carefully and press firmly; allow any adhesive to cure per manufacturer instructions