Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Connects washer drain hose to extension hose. Includes coupling and clamps. Replace if cracked, broken, or when extending drain hose length to reach pipe.
I ordered the drain extension kit and the hose connector kit. Read more
Fix a washer that won't advance through cycles or skips rinse with a new timer. This control part manages cycle progression. DIY repair in minutes.
I replaced the timer. Once the part arrived, it took about two minutes to put on and start the washer. Read more
This is a push button switch used to start and stop the wash cycle on a washing machine. It mounts on the control panel and engages the machine's control circuit when pressed. Replace this button if it feels loose, does not click properly, or the washer fails to start or stop when pressed.
Replaced the rubber button. Read more
Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.
Used from harness to top.
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I... Read more
Right hand side
New parts easy fix Read more
This is a small tube of silicone-based gasket sealer used to bond and seal gaskets during washer repairs. It creates a watertight seal between mating surfaces to prevent leaks around tub components or pump housings. Use this adhesive when replacing gaskets or resealing joints where the original sealant has deteriorated and water is leaking.
Fix unresponsive or erratic cycle selection with this rotary encoder switch. Mounts behind the control knob to restore accurate cycle settings and indicators.
Fixes grinding noise or basket won't spin issues by disengaging the brake during spin cycles. Restores smooth operation when cam wears out or breaks.
First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in... Read more
Factory mounting screw secures door closers, panels, and brackets in refrigerators and laundry centers. Replace stripped, missing, or rusted screws.
Includes suspension pads.
Screw: 8-16 x 3/8 inch.
Outer tub assembly holds wash water and houses the inner basket in top-load washers. Replace if cracked, leaking, or damaged during repairs.
Got all required parts and completed the job in 3 or 4 hours. Read more
This kit includes the clutch band and lining material used in the washer's transmission clutch assembly. The clutch band wraps around the clutch housing to engage the spin cycle, allowing the basket to gradually ramp up to full speed. Replace this kit if the washer fails to spin, spins slowly, or you hear grinding or scraping noises during the spin cycle.
Replaced clutch disc Read more
Machine screw that secures panels, brackets, and components in appliances. Replace when worn, stripped, or missing to restore tight fit and stability.
Knurled pin secures knobs or dials to control shafts in washers. Replace if the original is missing, worn, or damaged to stop loose or spinning knobs.
Weekend laundry became very noisy, our 1987 Whirlpool washer began doing a dance across the floor and the drum was banging into the inner cabinet. After doing some research and watching a few videos on Appliance parts pros website. I inspected the washer and noticed one leg the rubber coating disintegrated, decided to change all four legs, springs and lid switch. Hardest part of the job is getting the cabinet together. Ops check good. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.