Ngm8054uc Parts

Pressure regulator for gas cooktops maintains consistent gas flow to burners. Replace if leaking gas odor, damaged vent, or worn seals detected.

The Nut is an OEM component specifically designed for select Bosch gas cooktops. As a fastening mechanism, it firmly holds valves and brackets without loosening.  

Zinc plating resists corrosion ensuring dependable seating even under pot handles and continuous thermal expansion/contraction. Precision threading aligns without galling or binding that could jeopardize safe regulator positioning.

Causes requiring nut replacement commonly relate to wear through threads no longer maintaining clamping pressure on brass regulators over decades of use. Physical damage or over-tightening during assembly/service could also crack or distort housings.

Symptoms signaling the need for new nuts include:

• Gas leaks detected around valve connections or mounting points
• Loosened assemblies enabling unwanted vibrations from frequent cooking  
• Difficulty reaching proper tightening torques without hardware damage

This OEM Bosch replacement nut is also compatible with Thermador, Gaggenau, and some Kenmore ranges.
 

This is a gas flow control valve that regulates the supply of gas to an individual surface burner on a cooktop. It connects to the burner control knob and adjusts the flame from high to low. Replace this valve if a burner won't ignite, the flame is uneven or won't adjust properly, or if you detect a gas leak around the valve area.

Secure internal components with this mounting bracket. Replace if cracked, broken, or missing to restore proper fit and prevent movement inside your cooktop.

Secures 6mm shafts and spindles on cooktop burners and controls. Replace if parts slip or wobble during use. Confirm 6mm shaft size before ordering.

Burner cap for gas cooktops and ranges. Sits on top of the burner head to distribute flame. Replace if cracked, chipped, discolored, or missing.

Replace a faulty gas cooktop manifold if burners won't ignite, flames are uneven, or gas flow is restricted. Moderate DIY repair with proper tools.

This retaining washer secures a control shaft or hub to keep components in place during operation, helping restore proper control movement and prevent parts from sliding off the shaft. Simple replacement when a worn or missing retainer causes loose knobs or shifting parts. What it does:

• Fits onto a control or drive shaft to hold a knob, hub or gear in position
• Prevents axial movement that can cause loose or slipping controls
• Commonly replaced when the original washer is bent, cracked, or lost
• Works with compatible Bosch control assemblies and hubs

• One retaining washer

• Recommended for users comfortable with basic appliance disassembly; unplug appliance before starting
• Remove the control knob or panel per model instructions to access the shaft
• Press the washer into place on the shaft until fully seated; verify proper fit and control operation

Base component for gas cooktops that provides structural support and mounting. Replace if cracked, warped, or damaged to restore proper installation.

This replacement door gasket seals the dishwasher door to keep water inside the tub and help maintain wash performance. It restores a tight door seal to reduce leaks and prevent water from pooling around the appliance. What it does:

• Creates a watertight seal between the door and tub to stop leaks during cycles
• Helps prevent water from dripping onto floors and surrounding cabinetry
• Reduces steam and moisture escape that can cause odors or damage
• Restores proper door closure where worn or flattened seals allow seepage

• Disconnect power and water supply before attempting any service.
• Inspect surrounding door edges for damage and clean mounting surfaces before installing the new gasket.
• Press the gasket firmly into the door channel; some models require partial door disassembly.
• After installation, run a short cycle and check for leaks before returning the dishwasher to regular use.

Holder component for gas cooktops. Secures and positions internal parts in place. Replace if cracked, broken, or missing to restore proper assembly.

Burner holder for gas cooktops. Secures the burner assembly in place on the cooktop surface. Replace if cracked, broken, or causing burner instability.

Replacement mounting screw for cooktops and ranges. Secures panels, brackets, and components. Needed when original screw is missing, stripped, or damaged.

Stainless steel hex washer head screw for cooktop assembly. Replace missing, stripped, or damaged screws to secure components properly during repair.

Gas range burner cap sits atop the burner to distribute flames evenly for cooking. Replace if cracked, warped, or causing uneven flames. Verify fit with your model number before ordering.