Pavt-1 Parts

This cabinet top clip is a small plastic retainer that secures the appliance's top/cabinet to the chassis, keeping the cabinet aligned and preventing movement or rattling. It restores a flush fit between the cabinet and body. What it does:

• Secures the top/cabinet panel to the appliance frame so the cabinet stays in place
• Prevents the cabinet from shifting, vibrating, or sitting unevenly
• Helps stop gaps that can let dirt or moisture into cabinet seams
• Common symptom: loose, rattling, or misaligned cabinet top or trim

• One cabinet top clip

• Always disconnect power before servicing the appliance
• Remove necessary trim or panels to access the cabinet clip; a screwdriver or trim tool may be needed
• Replace broken or worn clips with matching parts only; inspect surrounding fasteners for damage

A stabilizer bracket that secures and supports internal components to reduce movement and rattle during operation. Helps restore stable alignment so the appliance runs quieter and more reliably. What it does:

• Provides structural support to help keep assemblies aligned and reduce excessive movement
• Dampens vibration and minimizes knocking or rattling noises tied to loose components
• Restores proper fit where a worn or broken bracket allowed shifting or misalignment
• Works as a repair for symptoms like intermittent noise, excess vibration, or parts that sag or shift

• Disconnect power (and water if appliance-specific) before beginning any repair
• Basic hand tools are usually required; refer to your model's service manual for exact steps
• Inspect surrounding parts for wear while replacing the bracket

This locknut is a small threaded retaining nut used to secure rotating and stationary appliance components, helping keep assemblies tight and stable during operation. It prevents parts from loosening and reduces vibration-related issues. What it does:

• Secures shafts, pulleys, or fittings to prevent axial movement
• Keeps assemblies fastened under normal vibration and load
• Helps stop wobble, grinding, or part separation caused by a loose connection
• Works with the matching threaded stud, shaft, or fitting for a proper hold

• Disconnect power and follow appliance safety procedures before servicing
• Use the matching thread size and engage threads fully; hand-start before tightening
• Tighten securely without overtightening; use the correct driver or socket for the nut
• Inspect mating threads and replace if damaged

Standard 8-18 x 3/8 inch mounting screw for securing panels, brackets, and components in appliances. Replace missing, stripped, or damaged screws.

Replacement timer control knob for washers. Restores manual cycle selection when original knob is cracked, broken, stripped, or missing. Installs on front panel.

Washer won't start or stops mid-cycle? This lid switch housing secures the switch assembly for reliable lid detection. Simple DIY fix in minutes.

Mounting screw used to secure panels, trim, brackets, and small appliance components. Replace a missing or damaged fastener to restore proper fit, reduce vibration, and keep parts aligned for safe operation. What it does:

• Secures panels, control boards, brackets, and trim to maintain correct assembly
• Replaces stripped, broken, or missing screws that cause loose or rattling parts
• Helps prevent misalignment that can interfere with doors, knobs, or covers
• Standard fastener interface — use the correct driver and size for a secure fit

• Disconnect power and/or gas and follow appliance safety procedures before servicing
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to avoid damage to threads or surrounding parts
• If threads are damaged, replace the mating component or use the correct thread-repair method

White decorative bezel that surrounds the timer control on your washer's console. Replaces cracked, broken, or missing skirts for a clean finish.

This is a top cabinet hinge used on a washing machine. It connects the top panel to the washer cabinet, allowing the panel to pivot open for access to internal components. Replace this hinge if it is bent, broken, or corroded, or if the top panel no longer opens, closes, or sits flush properly.

Size: 1.25OD x .530IDX.

Prevents oil leaks from the transmission area. Replace if you see oil puddles under your washer. Confirm fit with your model number before ordering.