Pdw7712 Parts

Secures panels, brackets, and hardware in your appliance. Replace when stripped, rusted, or missing to prevent looseness and vibration. Verify fit.

Replacement mounting screw for dishwashers. Secures components and panels inside the unit. Order a new screw if yours is stripped, missing, or damaged.

Water hardness test strip tool for dishwashers. Tests mineral content in tap water to help determine optimal detergent and rinse aid settings.

Specs: 8-18 b por 1/2 ss

Seals the water inlet funnel to prevent drips and direct water into the tub. Replace if you notice leaks at the inlet or water escaping during fill.

This fill funnel directs the incoming water into the dishwasher and helps contain the flow to prevent splashing and leaks. Replacing a cracked or worn funnel restores a proper, sealed water path during the fill. What it does:

• Channels incoming water into the dishwasher during the fill
• Helps seal the opening to reduce splashing and external leaks
• Common symptoms include water leaking during fill, moisture around the inlet area, or visible cracks/deformation of the funnel

• 1 fill funnel

• Disconnect power and shut off the water supply before servicing
• Access the funnel at the water entry point for your model
• Remove the old funnel; seat the new funnel evenly and ensure the seal is fully seated
• Reassemble and run a quick fill to check for leaks

Connects dishwasher wiring to the water inlet valve. Replace if the plug is burnt, brittle, loose, or corroded to restore a secure electrical connection.

Includes 12 screws.

This dome float is the replacement water-level float that helps the appliance sense and control the tub's water level, restoring reliable fill and shutoff behavior. Use this OEM-fit float when the original is cracked, stuck, or missing. What it does:

• Moves with rising and falling water to actuate the water-level mechanism and help prevent overfilling.
• Can reduce symptoms such as improper fill levels, continuous filling, or intermittent fill shutoff when the existing float is damaged or obstructed.
• Works as part of the washer's water sensing system—does not include electronic switches or housings unless shown.

• Disconnect power and unplug the appliance before starting any repair.
• Access may require removing the washer top or cabinet; follow your model's service instructions.
• Inspect surrounding hoses and clips; replace any damaged components and ensure the float moves freely.

This silicon controlled rectifier (SCR) is the control device that regulates high-current power to heating and motor circuits, helping restore proper operation when the original SCR fails. A direct-fit replacement part for the listed appliance control. What it does:

• Regulates and switches high-current power to heating elements or motor circuits as commanded by the appliance control board.
• Stops or reduces power flow when the SCR fails, which can cause no-heat or intermittent heating.
• Can cause symptoms such as no heating, intermittent operation, or incorrect cycle heating when faulty.
• Works with the main control to protect and time the appliance's heating cycles.

• SCR control

• Disconnect power before servicing to avoid electrical shock.
• Handle the part and wiring carefully; match terminals and mounting to the original unit.
• Follow the appliance service manual or wiring schematic for correct installation and testing.

This vent flapper is the exterior exhaust flap that opens to let dryer air and lint exit and closes to keep weather, pests and drafts out when the dryer is off. It restores proper airflow at the outside vent hood. What it does:

• Opens with dryer airflow to allow exhaust to escape and closes when idle to block outside air.
• Helps prevent backdrafts, pests and rain from entering the vent system.
• Can restore normal drying performance when a stuck or broken flap was restricting airflow.
• Commonly replaced when the flap is cracked, warped, jammed or does not seal.

• One vent flapper/exterior exhaust flap.

• Disconnect power to the dryer (and gas supply if applicable) and work from the outside hood when possible.
• Remove the exterior vent hood or access cover to inspect and replace the flap; basic hand tools required.
• Check that the flap moves freely after installation and seats against its seal to prevent air leaks.
• Clean or repair the ductwork to avoid repeat failures.

This replacement multi-purpose glass shelf provides a sturdy, easy-to-clean surface for organizing food and containers in your refrigerator. Restores usable shelving space after a chip, crack, or missing shelf. What it does:

• Supports refrigerated items and helps keep food organized and visible
• Replaces a cracked, chipped, broken, or missing refrigerator shelf
• Fits into existing shelf tracks or ledges to restore proper shelf spacing
• Tempered glass construction resists everyday cold-area wear (handle with care)

• Remove food and containers from the area before installing
• Handle the shelf carefully; wear cut-resistant gloves if replacing a broken shelf
• Slide shelf into the existing tracks/ledges until fully seated; do not force
• If glass is damaged on arrival, stop installation and contact the seller for a replacement

Secure wire harnesses in your dishwasher with this harness clip. Replace if wires are loose or clip is broken. Verify fit with your model number.

Rubber grommet cushions and seals dishwasher components. Replaces worn, torn, or missing grommets to restore proper fit and reduce vibration noise.

Replacement hex head screw for dishwasher component mounting. Secures solenoids, valves, and internal parts. Order when original is rusted, stripped, or missing.