Pfcs1rkzh Parts

This plug-in SCR is a solid-state replacement that controls electrical power to appliance circuits, restoring reliable on/off control and helping eliminate intermittent operation. It's a direct-fit replacement when the original SCR fails. What it does

• Regulates current flow in the control circuit to switch power to motors or heating loads.
• Stops erratic cycling or loss of power caused by a failed control semiconductor.
• Helps restore consistent operation when an appliance has intermittent start, no heat, or no motor run.
• Provides a rugged, compact replacement with a 5/16" connection style.

• One plug-in SCR

• Disconnect power to the appliance before accessing or replacing the SCR.
• Remove the appliance's control or access panel to reach the control board; note wire locations before unplugging.
• Plug the new SCR into the original connector or replace per the service manual.
• Verify correct operation after installation and reassemble all panels before restoring power.

Secures brackets, panels, and components inside your refrigerator. Replace stripped, rusted, or missing hardware to restore tight alignment and stability.

Flat head sheet metal screw for refrigerators. Secures panels, trim, and brackets with a flush finish. Replace if missing, stripped, or corroded.

Slide control knob that adjusts front-panel settings on your refrigerator. Replace if worn, cracked, or missing for smooth position selection.

Machine screw secures panels, brackets, and components in refrigerators. Replaces lost, stripped, or damaged 10-32 fasteners to restore stability.

Machine screw for refrigerator panels, brackets, and assemblies. Replaces lost, stripped, or damaged fasteners to restore secure fit and stability.

10-32 x 5/16 machine-thread screw secures refrigerator panels, trim, and internal brackets. Replaces missing or damaged fasteners to prevent rattles.

Phillips flat-head screw for securing panels, brackets, and trim inside your refrigerator. Replace missing or stripped screws to keep components aligned.

Wire tie retainer for refrigerators. Secures and organizes internal wiring. Replace if cracked, broken, or missing to keep wires properly bundled.

Seals the meat pan/deli drawer area to maintain proper airflow and reduce moisture and odors. Replace if worn or torn. Confirm fit with your model.

Seals the fresh food compartment tower to prevent air leaks and maintain temperature. Replace if worn, cracked, or causing frost buildup. Verify fit with your refrigerator model number before ordering.

This sound damper cushions the refrigerator compressor to reduce vibration and minimize noise for quieter operation. It helps protect the compressor from metal-on-metal contact and dampens normal operating sounds. What it does:

• Cushions compressor mounting to absorb vibration and reduce noise
• Prevents metal-on-metal contact that can cause rattling or buzzing
• Helps stabilize the compressor to reduce wear from vibration
• Commonly used when compressor noise, rattling, or increased vibration is noticed

• One sound damper

• Always disconnect power to the appliance before beginning any repair
• Access the compressor area (rear lower cabinet); remove any panels as needed
• Remove the old damper and press the replacement onto the compressor mounting foot until fully seated
• If mounting hardware is damaged or the compressor mount appears worn, replace mounting parts.

Bypass cap allows refrigerator water and ice dispensers to work without a filter installed. Replace if cracked or leaking. Confirm fit with your model.

The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the system. It helps maintain the purity and effectiveness of the refrigerant as it cycles through the system.

You should replace the R134 drier if it becomes clogged or damaged. Common causes of a bad drier include wear and tear over time, exposure to moisture, or contamination from other failing components in the refrigeration system.

Symptoms of a bad R134 drier include:

• Reduced cooling efficiency
• Frost buildup on the evaporator coils
• Unusual noises from the refrigeration system
• Increased energy consumption
• Refrigerator not maintaining the set temperature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Gear Pinion is an OEM component specifically designed for GE French door refrigerators. This part is responsible for the smooth operation of door hinges and closing mechanisms. 

The gear pinion works together with other inner door components to evenly distribute strength across the refrigerator’s motion system. This ensures doors move fluidly and stay securely sealed when closed. 

Causes of a bad gear pinion can include wear from repetitive use over many years, stress from overloading the doors, or misalignment of connecting mechanisms.

Symptoms of a bad gear pinion include: 

• Doors not closing or latching properly
• Binding or sticking movement  
• Noise or vibration when opening/closing
• Increased effort required to operate doors

Note: Right-hand side

Replace this precision gear with a genuine GE OEM part to restore dependable door functionality. This product is also compatible with Hotpoint, RCA, and Kenmore refrigerator models.