Pfi29psdc Parts

This handle assembly replaces a damaged or worn refrigerator fresh-food door handle to restore a secure grip and straight door appearance. It provides a factory-fit replacement that mounts where the original handle attaches. What it does:

• Replaces a cracked, loose or broken fresh-food door handle
• Restores a safe, comfortable grip for opening the refrigerator door
• Corrects misaligned or crooked handle appearance
• Helps the door latch and seal operate normally by providing proper handle support

• One handle assembly as shown

• Unplug the appliance or disconnect power before beginning any repair
• Keep original fasteners; install with the same screws or clips provided and tighten snugly — do not overtighten
• Handle with care to avoid scratching the door finish; wear gloves to protect hands from sharp edges

This self-adhesive foam strip provides a flexible seal and buffer for appliance gaps, helping reduce drafts, rattling, and moisture intrusion. Designed for easy stick-on replacement where foam padding or sealing is needed. What it does

• Seals small gaps between components to help reduce air leaks and temperature loss
• Cushions panels and doors to minimize noise and vibration
• Helps block moisture and dust from entering sensitive areas
• Self-adhesive backing allows for quick placement without extra glue

• One self-adhesive foam strip

• Surface must be clean and dry; wipe with isopropyl alcohol for best adhesion
• Measure and trim the foam strip to fit—use scissors or a utility knife
• Press firmly along the length to ensure full contact; allow adhesive to set before closing doors or panels
• For safety, disconnect power to the appliance before working in internal areas

This divider pan separates and supports crisper drawers to help keep produce organized and contained. It restores the original divider function so drawers slide and seal correctly, reducing shifts and spills inside the refrigerator. What it does

• Replaces a broken or missing divider that separates crisper drawers or pans
• Helps keep fruits and vegetables organized and contained to prevent mixing
• Supports proper drawer alignment and reduces unwanted movement or rattling
• Can stop small spills from spreading across the crisper area

• One divider pan

• Removal/installation is user-serviceable on most units; remove produce and gently lift or slide the old divider out before fitting the replacement
• Inspect surrounding rails and clips for damage; replace if worn to ensure proper fit
• Use gloves to avoid sharp sheet-metal edges and keep components clean during install

This replacement front pan cover gasket seals the refrigerator evaporator/drip pan area to help control moisture and direct defrost water into the drain. Restores a proper seal to reduce leaks and moisture buildup under the pan. What it does:

• Seals the front edge of the evaporator/drip pan to prevent water from escaping the pan area
• Helps route defrost and condensation into the drain system to avoid pooling
• Reduces moisture accumulation that can cause odors or frozen drainage
• Commonly replaced when old gasket is cracked, hardened, or missing

• One front pan cover gasket

• Inspect surrounding pan and trim for damage before installing; replace any broken clips or retainers
• Clean mating surfaces and remove debris to ensure a full seal
• Gasket typically presses into a channel or secures with clips—no special tools required, but a flat tool can assist seating
• Disconnect power to the appliance before servicing to avoid electrical hazard

Approximate dimensions: 15.3" x 4" x 4"

This condenser shroud is the plastic cover that protects and channels airflow around the refrigerator condenser, helping the cooling system run efficiently and keeping components shielded from debris. What it does:

• Directs airflow over the condenser coils to help dissipate heat
• Protects condenser and nearby components from dust, pet hair, and accidental contact
• Helps maintain proper clearance and airflow paths behind the fridge
• Can reduce vibration noise by stabilizing condenser area

• One condenser shroud/cover

• Designed to mount in the condenser compartment; follow your model's service manual for correct orientation and fasteners
• Disconnect power to the appliance before accessing the condenser area to avoid electrical shock
• Inspect and clean condenser coils while the shroud is removed for best performance
• If clips or screws are damaged, replace them with OEM-recommended hardware