Pfsf2mjxa Parts

This fan-mount grommet fits the evaporator or condenser fan assembly to isolate vibration and keep the motor aligned. Replacing a worn grommet can quiet rattles and prevent the fan blade from rubbing the housing. What it does:

• Isolates the fan motor from its bracket to reduce vibration and operating noise
• Helps maintain proper fan motor and blade alignment/clearance
• Replaces cracked, flattened, hardened, or missing grommets
• Typical symptoms: rattling, buzzing, or vibration sounds from the freezer or rear machine compartment

• 1 fan motor grommet

• Disconnect power before servicing; pull the refrigerator forward for rear access if needed
• Evaporator fan: remove the freezer's rear panel; condenser fan: remove the rear service panel
• Support the motor, remove the fan blade and mounting hardware as needed, replace the grommet, and reassemble
• Ensure the fan spins freely and does not contact the shroud before restoring power

This water tank assembly sits inside the refrigerator compartment and stores a reserve of water for the door dispenser. Replace it to stop leaks and restore proper, chilled water flow when the original reservoir cracks or bursts.

• Holds a supply of water for the door dispenser inside the fresh food section
• Uses refrigerator air to help deliver chilled water on demand
• Restores proper flow when a reservoir is cracked, leaking, or frozen/burst
• Typical symptoms: water under drawers, weak or no water from the dispenser, or warm water at the dispenser

• Disconnect power and shut off the household water supply before servicing.
• Remove shelves/drawers to access the tank; note tube routing and connection points.
• Release water lines per your connector type; ensure tube ends are cut square and fully seated during reassembly.
• Restore water, check for leaks, and run the dispenser to purge air from the system.

This vegetable pan cover frame supports the crisper glass and forms the top of the crisper compartment. Replacing a damaged frame restores proper drawer fit, level shelf support, and better spill containment inside your refrigerator.

• Supports the crisper cover glass to provide a stable shelf surface
• Forms the lid over the vegetable/crisper drawers to help contain spills
• Helps maintain proper drawer alignment and smooth operation
• Common symptoms: cracked or warped frame, sagging shelf, drawers binding or not closing, broken support tabs

• Disconnect power and remove food from the crisper area
• Slide out crisper drawers; carefully lift out the glass before removing the frame
• Transfer any reusable hardware from the old frame
• Seat the new frame, reinstall the glass and drawers, and verify smooth drawer movement

This compressor-mounted start device combines the start relay and overload protector. It helps the compressor start reliably and safeguards it from overheating, supporting consistent refrigerator cooling performance. What it does:

• Provides the initial boost to start the compressor, then disengages once it's running
• Protects the compressor circuit by opening if current draw or temperature is too high
• Common symptoms of failure: refrigerator/freezer warm, compressor won't start, repeated clicking, brief humming then shutoff, intermittent cooling
• Restores normal compressor starts when the original device has failed

• One TSD-2 compressor start device assembly

• Disconnect power before service; work in a dry area and follow manufacturer safety guidance
• Access the compressor compartment and note wire positions/terminal layout before removal
• Pull off the old device; push the new device fully onto the compressor pins; transfer wires one at a time to matching terminals
• If your model uses a run capacitor or retaining clip, move and reconnect them exactly as originally configured

The French Door Gasket is an OEM part for GE refrigerators. This gasket is designed to create a tight seal around the refrigerator's French doors, helping to maintain the internal temperature and ensuring energy efficiency. The gasket measures approximately 26 inches wide by 38 inches long.

Common causes of a bad gasket include wear and tear from regular opening and closing, exposure to temperature fluctuations, and accumulation of dirt or food particles that prevent a proper seal.

Symptoms of a bad French door gasket include:

• Visible cracks or tears in the gasket
• Condensation or frost buildup inside the refrigerator
• Increased energy consumption due to the refrigerator working harder to maintain temperature
• Difficulty closing the refrigerator doors properly

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Water Filter Housing and Tube Assembly is an OEM part for GE refrigerators. This assembly is responsible for securely holding the water filter in place while directing water through the filter and into the dispenser or ice maker. Approximate dimensions: 18" x 14.7" x 3.3"

Over time, the water filter housing and tube assembly can become damaged due to regular use, exposure to high water pressure, or mineral deposits building up inside the tubes. Such damage may lead to leaks or reduced water flow, affecting the performance of the refrigerator's water and ice systems.

Symptoms of a faulty water filter housing and tube assembly include:

• Water leaks around the filter area
• Low water flow to the dispenser or ice maker
• Difficulty installing or removing the water filter

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This vegetable pan support assembly holds and guides the crisper/vegetable drawer so it opens smoothly and keeps the cover/shelf above level. Replace a damaged support to restore proper drawer alignment and prevent sagging or sticking. What it does:

• Supports the crisper/vegetable drawer and the cover/shelf it rides on
• Maintains level alignment to reduce binding, scraping, or tipping
• Provides a stable track point for smooth drawer movement
• Common symptoms: drawer tilts, binds, or falls; shelf sags; visible cracks or broken tabs on the support

• 1 vegetable pan support assembly

• Unplug the refrigerator before servicing
• Remove the crisper drawer and cover/shelf to access the support
• Match the new support's orientation to the original; transfer any reusable hardware if applicable
• Seat the support fully and securely before reinstalling the cover/shelf and drawer; test drawer travel

This #8-18 x 5/8-inch Torx T20 screw secures panels, brackets, and trim in your appliance. It replaces missing or damaged hardware to restore a tight, reliable hold and reduce looseness or rattling.

• Fastens sheet-metal or plastic components to the appliance cabinet or frame
• Replaces missing, stripped, or corroded screws to maintain proper fit
• Helps reduce vibration and rattling from unsecured parts
• Torx T20 drive; #8-18 thread; 5/8-inch length

• Disconnect power and shut off water before servicing
• Use a T20 Torx driver; start threads by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping
• Wear cut-resistant gloves; sheet-metal edges can be sharp

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly

Color: Black

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

This refrigerator French door gasket restores a tight seal around the door opening. Replacing a worn or damaged gasket helps keep cold air in and humid air out to maintain stable temperatures and reduce condensation. What it does:

• Forms an airtight seal between the door and the cabinet on French-door models
• Helps prevent warm air leaks, moisture buildup, and frost around the door opening
• Replace if torn, warped, cracked, or if gaps remain when the door is closed
• Common signs include condensation on or around the gasket and the door not sealing fully

• 1 door gasket

• Unplug the refrigerator and remove items from the door bins
• Warm and relax the new gasket (soak in warm water or use low heat) to remove kinks; do not overheat
• Lift the old gasket out of the retainer; if your model uses retainer screws, loosen them, swap the gasket, then re-tighten
• Press the new gasket fully into the channel, ensure corners seat, then close the door and check for an even seal all around

This shelf module assembly restores a sturdy, level storage surface inside your refrigerator. Replace a damaged or missing shelf to recover usable space and keep items organized and easy to access. What it does

• Provides a flat, stable surface to support food containers in the refrigerator compartment
• Restores storage capacity when the original shelf is broken, warped, or missing
• Helps keep contents organized and accessible
• Addresses issues like sagging, instability, or a shelf that won't stay seated in its rails

• One shelf module assembly

• Disconnect power to the refrigerator before servicing
• Remove items from the area and slide/lift out the old shelf
• Transfer any reusable trims or components from the old shelf
• Fully seat the new shelf in the side rails; ensure it's level and secure before reloading

The damper duct assembly regulates the cold air sent from the freezer into the refrigerator compartment. Replacing a worn or sticking damper restores proper airflow and helps the fresh food section maintain stable, even temperatures.

• Regulates airflow from the freezer into the refrigerator compartment
• Helps maintain set temperatures by opening and closing to meter cold air
• Common failure signs: fresh food too warm, items freezing near the vent, weak/no airflow from the vent, or clicking/buzzing from the damper area

• Disconnect power to the refrigerator before servicing
• Remove shelves and the duct/vent cover; retain screws and clips
• Unplug the wire harness and swap the assembly; transfer any reusable hardware
• Ensure seals seat fully to prevent air leaks; restore power and allow temperatures to stabilize

This refrigerator door gasket creates an airtight seal between the door and cabinet to keep cold air in and moisture out. Replacing a worn or damaged gasket helps restore proper sealing, temperature stability, and efficiency. What it does:

• Seals the door perimeter to prevent air leaks and energy loss
• Helps maintain consistent interior temperatures
• Reduces frost buildup and condensation around the door opening
• Addresses issues like torn, warped, or compressed gasket material and doors not sealing fully

• 1 door gasket

• Unplug the appliance before servicing; open the door fully for access
• Let the new gasket warm to room temperature; gently warm with low heat or warm water to relax folds
• Remove the old gasket from the retainer/channel; on some models loosen retainer screws
• Seat the new gasket starting at the corners, then work along each side; tighten any retainers evenly and check for a uniform seal all around