Pfsf2mjxa Parts

This spring closure is the OEM-style replacement that helps a door or panel return to a closed position smoothly and reduces slack or slamming for improved alignment and operation. It fits the original mounting points and restores the intended closing action. What it does:

• Provides the tension needed to pull a door/panel closed and hold it in place
• Restores consistent closing action when the original spring is worn or broken
• Helps reduce noisy slamming and prevents partial-open gaps that affect seal and alignment
• Works with the door/panel linkage to improve day-to-day usability

• One spring closure

• Turn off power to the appliance or unplug it before starting any repair
• Verify correct orientation and routing before fastening; spring tension can cause sudden movement
• Use appropriate hand tools and eye protection; if the original mounting clips are damaged, replace them as well

This leveling screw threads into the refrigerator's leveling leg or adjuster bracket to raise or lower the cabinet. Replacing a stripped or missing screw restores stable footing and helps keep doors aligned for proper sealing.

• Provides threaded height adjustment of the leveling leg/roller bracket
• Helps stop rocking or wobbling that can cause vibration and rattling
• Aids in door alignment so doors close and seal properly
• Replace if threads are stripped, screw is bent, seized, or missing

• Disconnect power and turn off the water supply before servicing
• Protect flooring; with assistance, carefully tip the appliance slightly to relieve weight from the adjuster
• Remove the damaged screw; hand-start the new screw to avoid cross-threading, then adjust until level
• Verify the cabinet is stable and doors operate correctly before restoring power

This tube clamp secures flexible water tubing to its fitting in refrigerators. It helps maintain a tight seal to prevent leaks and keeps lines from slipping off under normal operating pressure.

• Holds plastic or rubber tubing firmly on a barbed fitting or nipple
• Helps prevent drips and leaks at tube connection points
• Addresses loose or disconnected water lines
• Useful when tubing slips off or won't stay seated

• Disconnect power and shut off the water supply before servicing
• Position the clamp over the tube and fitting; compress with pliers and release to lock in place
• Ensure the clamp is centered and fully seated; tug-test the tube
• Restore water and power; check all connections for leaks

Small replacement bumper that mounts on a French-door to cushion contact, reduce rattling and protect the door and cabinet from wear. Restores smoother closing and helps maintain proper door alignment. What it does:

• Cushions the door to prevent metal-to-metal contact and reduce noise.
• Protects the door edge and cabinet finish from wear and impact damage.
• Helps the door align and seat properly for an even, quiet close.
• Commonly used when doors rub, squeak, or close unevenly.

• Disconnect power to the appliance before starting any work.
• Typically installs by pressing or seating into the designated bumper hole or post; may require removing the door or loosening a hinge for full access.
• Inspect surrounding mounting hole and adjacent bumpers; replace any additional worn bumpers for consistent fit.

This replacement filter bypass adapter lets a refrigerator water line run without a filter cartridge installed, providing a secure connection so the dispenser and ice maker can continue to get water when a filter is removed. What it does:

• Replaces the filter cartridge with a sealed bypass so water flows through the housing without a filter element
• Restores normal dispenser and ice maker flow after removing or bypassing a cartridge
• Prevents leaks at the filter housing when a cartridge is not installed
• Useful when using an alternate filtration system or awaiting a replacement cartridge

• Shut off the water supply and run the dispenser until flow stops before starting
• Remove the old filter or cartridge per the owner's manual, then install the bypass in the same orientation
• Inspect the housing O-ring and replace if damaged to ensure a tight seal

This replacement screw secures appliance brackets, panels, and components. It restores a tight, aligned fit when the original hardware is stripped, rusted, or missing, helping reduce vibration and rattling for reliable operation.

• Fastens brackets, panels, or mounts to keep components secure and aligned
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration, rattling, or loose/misaligned parts
• Matches original spec for reliable hold and fit

• Disconnect power before servicing; use proper PPE
• Match thread and length to the removed screw before installation
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Ensure parts are aligned and seating surfaces are clean before tightening

This 10-32 x 1/2 machine screw secures appliance components where a standard 10-32 fastener is required. It restores proper mounting and reduces vibration or loose panels for reliable, quiet operation. What it does:

• Secures panels, brackets, or components that use a 10-32 threaded hole
• Prevents rattling, misalignment, and intermittent contact caused by loose fasteners
• Maintains electrical or mechanical connections when used as the OEM-specified screw
• Helps restore fit and finish after repair or disassembly

• Use the correct 10-32 driver (Phillips or slotted depending on head) and hand-start the screw to avoid cross-threading
• Tighten until snug; avoid over-tightening to prevent stripping threads or cracking plastic parts
• Replace only with the same size and thread spec to ensure proper fit
• Disconnect power if working near energized components or wiring

This is a silicon controlled rectifier (SCR) used in appliance control circuits to regulate power to heaters or motors, helping the appliance deliver consistent operation and heat when needed. What it does:

• Acts as a switch in the control circuit to regulate current flow to heating elements or motors
• Can prevent or allow power to the load based on control signals from the appliance module
• Common symptom indicators: intermittent or no heat, unit won't reach operating temperature, or inconsistent operation of the controlled component
• Used where precise control of AC power is required for safe, efficient performance

• One silicon controlled rectifier (SCR) as described

• Disconnect power to the appliance before servicing to avoid shock or injury
• Handle the part carefully; avoid bending terminals and observe anti-static precautions
• Verify wiring and terminal orientation matches the original before reconnecting

This is a 1/4-20 UNC machine screw used to fasten appliance components securely. It restores proper fit and stability where threaded fasteners are required, preventing loose panels or shifting parts. What it does:

• Secures panels, brackets, or assemblies that use a 1/4-20 UNC threaded hole
• Stops rattling or movement caused by a missing or damaged screw
• Restores correct mechanical connection for safe operation
• Useful when replacing stripped, corroded, or lost fasteners

• Disconnect power to the appliance before servicing.
• Start threads by hand to avoid cross-threading; tighten until snug.
• Do not overtighten — use appropriate torque for the material to avoid stripping threads or damaging parts.
• Ensure proper contact and secure fastening.

This replacement roller pan supports and guides the oven or range storage drawer, restoring smooth sliding and helping contain spills or crumbs under the drawer. It installs behind the drawer to stabilize rollers and track movement. What it does:

• Holds and aligns the storage-drawer rollers so the drawer opens and closes smoothly
• Helps contain crumbs and minor spills beneath the drawer area
• Reduces drawer sagging, sticking or noisy operation when rollers are worn or damaged
• Restores proper drawer tracking and prevents misalignment

• One replacement roller pan

• Disconnect power to the appliance before servicing to avoid injury
• Remove the oven/storage drawer to access the pan
• Inspect rollers and bracket hardware; replace any damaged fasteners or rollers as needed
• Use basic hand tools; reassemble carefully and test drawer operation after installation

This slide control is the user-operated slider that adjusts a front-panel setting, restoring smooth, reliable position selection and tactile feedback. It replaces worn or damaged sliders so controls respond predictably. What it does:

• Moves along a track to change a user control setting (e.g., temperature, speed or level) and provides a detented position feel
• Restores mechanical connection between the user knob/slider and the internal control mechanism
• Commonly replaces units that are stuck, loose, broken, or provide intermittent contact
• Helps eliminate slipping or poor tactile feedback when selecting settings

• One slide control assembly as shown

• Disconnect power to the appliance before starting any repair
• Most installs require removing the console or control panel; keep screws and small parts organized
• Handle plastic tabs and mounting features gently to avoid breakage
• Ensure secure mating and correct orientation before reassembly

A short 8-32 x 3/8 hex washer head screw used to secure small appliance panels and components. Simple replacement for stripped or missing fasteners to restore proper fit and prevent rattles or loose parts. What it does:

• Secures panels, brackets, and small assemblies in place
• Helps eliminate vibration-related noise from loose parts
• Replaces missing, damaged, or corroded screws to restore proper alignment
• Fits standard 8-32 threaded holes requiring a 3/8" length screw

• One 8-32 x 3/8 hex washer head screw

• Use the correct 8-32 driver to avoid stripping the head
• Tighten snugly but avoid over-torquing to prevent thread damage
• Disconnect power and follow appliance safety procedures before accessing internal components
• Replace only like-for-like fasteners in load-bearing or safety-critical locations