Pfss22mjycss Parts

This small set screw secures components inside your refrigerator. Replacing a missing or stripped set screw restores a tight, reliable hold so attached parts stay aligned and are less likely to loosen or rattle during use.

• Fastens an attached part to its mounting point to prevent movement or slipping
• Helps maintain proper alignment of handles, brackets, or trim pieces
• Reduces wobble, vibration, and rattling noises caused by loose hardware
• Replaces missing, stripped, or corroded set screws

• Unplug the refrigerator and shut off water if working near door/dispenser areas
• Support the part being secured; start the screw by hand to avoid cross-threading
• Tighten with the correct driver for your model; do not overtighten to prevent stripping
• The component is secure and aligned before restoring power

This OEM fastener secures interior components and trim on compatible appliances to restore proper fit and reduce movement. It's a direct-replacement hardware piece used where the original mounting screw or retainer is lost or worn. What it does

• Secures panels, trim pieces, brackets or small assemblies to the appliance frame
• Restores firm attachment to reduce rattles, gaps or misalignment
• Replaces missing or stripped hardware that prevents proper part installation
• Helps maintain proper operation by keeping service parts seated and stable

• Disconnect power or unplug the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Hand-start the fastener, then tighten snugly—do not over-torque
• Replace any additional damaged fasteners with the same OEM part for best fit

This silicon controlled rectifier (SCR) is an electronic switching device used to control power to oven/stove heating circuits, helping the appliance regulate temperature and heat output for cooking performance. What it does:

• Switches and regulates AC power to heating elements for controlled heat
• Enables cycle-based or phase-controlled heating used by oven/range controls
• Common replacement when an element won't heat consistently or unit won't maintain temperature
• Helps stop erratic heating caused by a failed power control component

• Disconnect power to the appliance before inspecting or replacing the SCR
• Observe ESD precautions and handle the component by insulated edges

This damper is the refrigerator air-flow control that opens and closes to direct cold air between compartments, helping maintain proper cooling balance. Replaces a worn or stuck damper to restore regulated airflow and more consistent temperatures. What it does:

• Controls the amount of cold air moved from the freezer into the refrigerator compartment.
• Opens and closes based on the fridge's temperature control signals to balance compartment temperatures.
• A faulty damper can cause uneven cooling, a warm fresh food section, or overcooling in one compartment.
• Works with the existing housing and linkage to modulate airflow as commanded by the control board.

• One damper assembly

• Disconnect power to the appliance before starting any repair to avoid electric shock.
• Remove interior panels or shelves as needed to access the damper; keep fasteners for reassembly.
• Handle plastic components gently to avoid cracking; test damper operation after reassembly.

This damper assembly controls airflow between refrigerator compartments to help maintain even temperatures. It replaces a worn or stuck damper to restore proper cold-air balance and improve cooling performance. What it does:

• Opens and closes to regulate cold-air flow from the freezer to the fresh-food section
• Can restore airflow when the refrigerator is warmer than the freezer or compartments are unevenly cooled
• Helps correct symptoms such as poor cooling, fluctuating temperatures, or a freezer that's much colder than the fridge
• Works with the refrigerator's temperature controls to maintain set temperatures

• One damper assembly

• Disconnect power to the appliance before starting any repair
• Locate the damper in the fresh-food section near the top or the freezer-to-fridge air duct; remove shelves or covers as needed for access
• Handle the actuator and linkage gently; ensure correct orientation and secure mounting when installing
• After installation, reconnect power and allow the refrigerator several hours to stabilize; verify airflow and temperature operation

This silicon controlled rectifier (SCR) is a replacement control semiconductor that helps regulate power to heating elements and motors, restoring proper cycle control and heat delivery in compatible appliances. What it does:

• Controls and chops AC power to heating elements or motor circuits for variable heat/speed control
• Can stop intermittent or no-heat conditions caused by a failed SCR in oven, range, or similar appliances
• Helps restore stable thermostat/regulation behavior when the original SCR is not switching correctly
• Commonly used where precise power control is required in the appliance's control board or module

• One silicon controlled rectifier (SCR) as shown

• High-level, service-only replacement — disconnect power before starting work
• Verify correct part number on the appliance and transfer heat sinks or mounting hardware if required
• Use proper ESD precautions when handling semiconductor components

This replacement dairy door restores a sealed compartment on the fridge door to keep butter, cheese and small items contained and organized. It replaces a cracked, broken or missing dairy door to improve closure and appearance. What it does:

• Provides a covered compartment on the inner door to keep small dairy items organized and contained
• Replaces cracked, broken or warped dairy doors that no longer latch or sit flush
• Helps reduce shifting and spills on the door shelf
• Restores proper fit and appearance to the refrigerator door interior

• One dairy door assembly

• Remove items from the door bin and lift or unclip the old dairy door per your model's instructions
• Align the replacement door with the hinge/slots and snap into place until it seats securely
• Inspect for proper closure and latch engagement before returning contents
• Use gloves to protect hands from sharp edges; unplug or disconnect power only if recommended by your model's service manual

This refrigerator vegetable crisper drawer body provides a durable storage pan for fresh produce, helping contain spills and keep fruits and vegetables organized and accessible. Fits into the crisper compartment and replaces a cracked or worn drawer body. What it does:

• Replaces the main vegetable/crisper drawer pan that holds produce and contains leaks or spills
• Restores proper fit and function of the crisper compartment so the drawer slides and seals correctly
• Helps prevent loose items from falling into lower compartments and simplifies cleanup
• Works with the existing drawer front, tracks, and humidity control components

• Remove food and any loose parts before replacing; handle glass shelves with care
• Usually slides into tracks or snaps into position; keep hardware from the original drawer for reassembly
• If damaged tracks or drawer front are present, inspect related components and replace as needed
• Unplug or disconnect power only if required by your refrigerator model and follow OEM safety guidance

A short 8-32 x 3/8 hex washer head screw used to secure small appliance panels and components. Simple replacement for stripped or missing fasteners to restore proper fit and prevent rattles or loose parts. What it does:

• Secures panels, brackets, and small assemblies in place
• Helps eliminate vibration-related noise from loose parts
• Replaces missing, damaged, or corroded screws to restore proper alignment
• Fits standard 8-32 threaded holes requiring a 3/8" length screw

• One 8-32 x 3/8 hex washer head screw

• Use the correct 8-32 driver to avoid stripping the head
• Tighten snugly but avoid over-torquing to prevent thread damage
• Disconnect power and follow appliance safety procedures before accessing internal components
• Replace only like-for-like fasteners in load-bearing or safety-critical locations

This clip retainer secures trim, panels, or wire harnesses to keep components stable and reduce noise or wear. It's a small but important fastener that helps maintain proper fit and routing inside the appliance. What it does:

• Secures wiring or harnesses to prevent rubbing, pinching, or strain that can cause intermittent connections
• Holds panels and trim in place to reduce vibration and rattling during operation
• Keeps components aligned for reliable door/trim fit and proper clearance
• Helps prevent wear on insulation and nearby parts by keeping parts stationary

• Disconnect power before servicing to avoid shock or injury
• Remove trim or access panels as needed to reach the damaged clip
• Replace the broken clip with the new retainer; ensure the harness or panel is seated correctly in the clip
• Replace them to ensure secure reassembly

This handle assembly replaces a damaged or worn refrigerator fresh-food door handle to restore a secure grip and straight door appearance. It provides a factory-fit replacement that mounts where the original handle attaches. What it does:

• Replaces a cracked, loose or broken fresh-food door handle
• Restores a safe, comfortable grip for opening the refrigerator door
• Corrects misaligned or crooked handle appearance
• Helps the door latch and seal operate normally by providing proper handle support

• One handle assembly as shown

• Unplug the appliance or disconnect power before beginning any repair
• Keep original fasteners; install with the same screws or clips provided and tighten snugly — do not overtighten
• Handle with care to avoid scratching the door finish; wear gloves to protect hands from sharp edges