Pg364gebs/05 Parts

This electronic PC board is the appliance's main control, processing inputs and directing power to components so cycles run correctly. Replacing a failed board can restore normal operation when the unit is dead, won't start, or stops mid-cycle.

• Interprets user inputs and sensor feedback to execute programmed cycles
• Switches relays to power motors, valves, heaters, and other loads as required
• Manages timing, temperature, and safety logic for consistent performance
• Typical failure symptoms: no power/won't start, unresponsive or erratic controls, cycles ending prematurely, recurring error codes

• Disconnect power before servicing; verify power is off with a meter
• Use ESD protection; handle the board by the edges to avoid static damage
• Move connectors one at a time to identical positions on the new board to prevent miswiring
• Some models require service-mode setup or calibration after installation—follow your model's service documentation

Replacement drip pan for gas cooktops and ranges. Sits beneath burners to catch spills and protect the cooktop base. Replace if cracked, warped, or rusted.

This rotary potentiometer converts shaft rotation into an electrical signal the control board can read, providing precise position feedback for user selections. Replace it if inputs become erratic, jump between settings, or the control stops responding.

• Provides rotary position feedback to the electronic control
• Enables accurate selection and adjustment of functions or setpoints
• Wear or damage can cause drifting, dead spots, or incorrect readings
• Intermittent or no response to input is a common failure symptom

• Disconnect power before servicing
• Access the control/console area to reach the component
• Note shaft orientation and any connector positions; transfer exactly to the new part
• Handle electronics with ESD care and verify smooth, full-range operation after reassembly

Replacement selector knob for your range. Fits onto the control shaft to select functions, cycles, or heat levels. Needed when original is cracked, broken, or missing.

This compression sleeve forms the sealing ring for a 5/16-inch tubing compression joint, restoring a watertight connection when used with a matching compression nut and fitting. Ideal for stopping leaks and restoring reliable water lines. What it does:

• Creates the compression seal on 5/16" tubing when installed with a compatible compression nut and fitting.
• Stops leaks or drips at compression-style water connections.
• Used on appliance water lines (ice makers, water inlets) and other 5/16" tubing joints.
• Replaces worn or damaged sleeves that fail to hold a tight seal.

• Shut off the water supply and relieve pressure before working on water lines.
• Inspect and cut tubing squarely; slide the sleeve onto the tube before threading the compression nut and fitting.
• Tighten the compression nut per the fitting manufacturer's instructions and check the joint for leaks.
• Replace the sleeve if damaged or deformed.

If your burners won't ignite or flames are weak, a damaged gas supply tube may be blocking fuel flow. This 9-inch tube restores proper gas delivery. 2-hour DIY repair.

Oven light not working or flickering? This low-voltage transformer powers your range's interior lights. Restores proper oven lighting function.

This indicator light illuminates to show when a burner or oven element is active or still hot. It is mounted on the control panel and provides a visual safety alert during and after cooking. Replace this part if the indicator fails to light up when a burner is on, stays lit continuously, or appears dim and flickering.

Replace your cracked or faded control panel insert trim to restore appearance and proper button alignment. Fits into the control area for a clean look.

Fix leaks or flow issues in your range with this routing tube. Replaces worn or cracked tubes to restore proper liquid and airflow in your appliance.

Small hardware pin that secures or pivots components in gas ranges and cooktops. Replace if worn, missing, or broken to restore proper alignment.

Fix erratic temperature readings or a stuck display on your range. This temperature display assembly restores clear temperature readouts and control feedback.

If your gas range broiler won't ignite or stays on continuously, the broil solenoid controls gas flow to the broil burner and may need replacement.

This pressure regulator controls and stabilizes incoming water pressure to the appliance, helping maintain consistent operation and protect internal valves and seals. Fits systems that use a 3/4 inch inlet regulator. What it does:

• Reduces high incoming water pressure to a safe, steady level for the appliance
• Prevents pressure-related leaks, valve chatter, and premature wear on seals
• Helps maintain consistent water flow for reliable cycles and operation
• Commonly replaced when irregular pressure, humming valves, or water leaks occur

• One pressure regulator (3/4 in.)

• Turn off water supply and power to the appliance before starting; relieve system pressure first
• Inspect connection fittings and seals; use appropriate thread sealant if required by the OEM
• Tighten to manufacturer torque recommendations and check for leaks after restoring water

If your burner won't light or gas flow is weak, this valve controls fuel delivery to each burner. Moderate difficulty repair, typically 30-60 minutes.

90-degree elbow orifice holder for gas ranges and cooktops. Replace this gas line connector if cracked, broken, or causing improper gas flow alignment.