Pgs908sem-Ss Parts

Drawer wedge guide aligns and stabilizes your range's lower drawer for smooth operation. Replace if cracked, broken, worn, or missing to eliminate wobble.

This tangential blower moves cooling air through the appliance to protect internal components and the control area from excess heat. Replace a noisy or non-running fan to restore proper airflow and safe operating temperatures. What it does

• Circulates air across the appliance cavity and control compartment during and after heating cycles
• Helps prevent over-temperature shutdowns and protects electronic controls
• Reduces heat at the control panel and vent area
• Common symptoms: fan won't run, runs intermittently, or makes loud scraping/rumbling noises

• One tangential blower

• Disconnect power and allow the appliance to cool completely before servicing
• Access location varies by model; document wire connections and mounting orientation before removal
• Transfer any brackets, screws, or insulation from the original part if needed
• The fan spins freely and matches the original airflow direction before reassembly

Replacement screw for securing oven components, panels, and brackets. Restores tight mounting when original screws are missing, stripped, or lost.

Secures components to your appliance chassis for a rattle-free fit. Replace missing, stripped, or corroded screws to keep panels and brackets aligned.

This small cooktop bracket secures designated components beneath the cooktop surface, keeping them properly positioned and stable. Replace a damaged or missing bracket to restore alignment and reduce movement or rattling during use.

• Provides mounting support for specific under-top components, per model design
• Helps maintain proper alignment and stability of cooktop parts
• Replace when visibly bent, cracked, or corroded

• Disconnect power; for gas models, also shut off gas and allow the unit to cool
• Remove surface components as required (grates/caps/heads for gas; elements/panels for electric) to access under the top
• Lift or remove the cooktop as directed in your model's service information and secure the new bracket with existing hardware
• Reassemble, verify alignment, and for gas units check for leaks if any gas connections were disturbed

This metal bracket mounts beneath a cooktop surface burner and holds the orifice and burner base in position. It ensures proper alignment of the burner assembly for safe and efficient gas flow. Replace this bracket if it is bent, corroded, or broken, which can cause the burner to sit unevenly or not ignite properly.

Replacement screw for securing panels, brackets, and internal components in ranges, ovens, and cooktops. Replace missing, stripped, or damaged screws.

Thermal insulation that fits between inner and outer oven door panels along the side edge. Replace when burnt, brittle, cracked, or missing from wear.

Seals the right edge of your electric range cooktop to prevent spills from entering the chassis. Replace if worn, cracked, or no longer sealing properly.

6-20 x 3/8 inch nickel screw secures trim panels, brackets, and small components in dishwashers and ovens. Replace missing or stripped screws.

Right-side oven door hinge that pivots and supports the door for proper alignment. Replace when worn, damaged, or broken to restore smooth operation.

Tangential blower that moves air through the oven's ventilation and control areas to help keep components cool and vent heat. Replacing a failed blower restores airflow for quieter operation and more consistent cooling around electronics. What it does:

• Circulates air across the oven vent and control area to dissipate heat; symptoms of failure include little or no airflow.
• Helps cool control electronics and nearby components; failure can cause high temperatures or thermal-related shutdowns.
• Reduces noisy or rough fan operation when bearings or motor wear.
• Supports proper venting after use to help the appliance cool down safely.

• Disconnect power to the appliance before accessing or replacing the blower.
• Allow the appliance to cool fully; remove access panels to reach the blower.
• Handle the blower and connector gently to avoid damaging the motor shaft or wiring; ensure correct orientation when reinstalling.

This flat washer (.250 inch inner diameter x .812 inch outer diameter) is a simple replacement part that helps distribute load from a fastener and protects mating surfaces for reliable appliance operation. What it does:

• Provides a stable bearing surface for screws, bolts or studs to reduce wear on parts
• Helps distribute clamping force to prevent pull-through or deformation of softer materials
• Reduces vibration and movement at the joint when installed correctly
• Missing or damaged washers can lead to loose fasteners, increased vibration or component misalignment

• Disconnect power and water before servicing the appliance
• Replace like-for-like: inner/outer diameters and thickness match the original washer
• Inspect mating hardware and surfaces for damage; replace corroded or deformed fasteners as needed
• Tighten fasteners evenly and avoid over-torquing to prevent washer or component damage

This SPDT high-amp switch controls high-current circuits by switching one input between two outputs, restoring proper electrical control in affected appliance functions. Built for high-load switching where reliable on/off selection is required. What it does:

• Directs high-current power from a single input to one of two outputs (single-pole, double-throw action)
• Replaces worn or failed selector/limit-style switches that cause intermittent or no power to a circuit
• Commonly used where a high-amp, durable switching contact is required to complete a function
• Helps stop symptoms like intermittent operation, failure to switch between states, or no power to the controlled circuit

• One SPDT high-amp switch (WB24T10160)

• Disconnect power to the appliance before inspecting or replacing the switch
• Verify wiring locations and take a photo before removal for correct reconnection
• Use proper tools and avoid touching energized contacts;

Replacement screw secures panels, brackets, and trim inside your oven or range. Restores tight fit when original hardware is missing, stripped, or damaged.

Small rubber bumper that cushions contact between oven door and cabinet. Replace if cracked, missing, or worn to reduce noise and protect finishes.