Phs120a-3377 Parts

Replace a cracked or broken refrigerator cover. This cosmetic part installs to conceal internal components and maintain a clean appearance.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

The Wiring Harness is an OEM part for Frigidaire refrigerators. It connects various electrical parts within the refrigerator, ensuring proper communication and voltage.

A bad wiring harness can be caused by wear and tear, damage, or electrical issues. Signs of a faulty wire harness include malfunctioning or non-functional parts, intermittent electrical problems, or loose connections.

Symptoms of a bad wiring harness can include:

• Intermittent electrical issues or power loss
• Burnt or melted wires
• Visible damage or wear on the wire harness

Replace your worn or damaged wiring harness with this genuine OEM part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This drawer gasket forms the sealing edge for a refrigerator drawer to help maintain proper compartment temperature and reduce air exchange. It restores a tight seal so stored food stays fresher and the appliance runs efficiently. What it does:

• Replaces a worn or torn drawer seal that allows warm air into the drawer
• Helps reduce frost buildup, moisture, and premature spoilage of food
• Improves compartment temperature stability and cooling performance
• Prevents drafts and rattling caused by a loose or damaged gasket

• One drawer gasket

• Remove the drawer and old gasket, clean mounting channel before installing the new gasket
• Press gasket into the channel evenly; some designs clip or tuck into a retainer—avoid sharp tools that could damage the new seal
• If gasket is stiff, warm briefly with a hair dryer on low to ease installation; allow to cool and set before use
• For safety, unplug the appliance or switch off power before servicing

This handle and end cap assembly replaces a damaged or worn door handle to restore a secure grip and clean appearance. It's a direct-fit exterior part used on compatible GE refrigerator/freezer doors. What it does:

• Provides a finished grip surface for opening and closing the door
• Replaces cracked, broken, or loose handles and end caps
• Restores proper alignment and attachment where the original handle is damaged
• Improves door appearance by replacing worn or discolored components

• High-level installation; verify correct orientation and attachment hardware before starting
• Turn off and empty the door area as needed for safe access
• Use appropriate hand tools; avoid overtightening fasteners to prevent cracking

This is a replacement black screw used to secure interior or exterior appliance components. It provides a discrete, color-matched fastener to restore proper fit and stop rattles or loose panels. What it does

• Fastens trim, panels, brackets or control components where a small black screw is required
• Restores secure mounting to eliminate vibration, rattling or misaligned parts
• Matches finished appliance surfaces for a clean, unobtrusive look
• Simple hardware replacement for small fastener loss or damage

• One black screw

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver to seat the screw; avoid overtightening to prevent stripping or cracking surrounding material
• Keep track of small fasteners during disassembly and handle with care
• Replace with the exact part number if the original screw is damaged or the thread/length differs

If your range burners won't ignite or spark intermittently, this generator board assembly controls ignition functions. Moderate DIY repair restores reliable lighting.

Loose control panel or rattling cabinet? This 10-32 machine screw secures panels, brackets, and components in your top-load washer. Simple install.

Rubber grommet that mounts and cushions the compressor to reduce vibration transfer. Replace if cracked, worn, or missing to restore quiet operation.

Protective cover that shields the refrigerator motor assembly. Replace if your cover is cracked, broken, or missing to protect internal components.

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

Refrigerator not cooling or freezing properly? A faulty evaporator coil may be causing warm temps and moisture buildup. Professional installation recommended.

This is a factory-style replacement screw used to secure appliance components. It restores proper fastening where the original screw is missing, stripped, or damaged so panels and assemblies stay firmly attached. What it does:

• Fastens panels, brackets, or components to the appliance frame or assemblies
• Replaces missing or damaged mounting hardware that can cause rattles or loose parts
• Provides the correct fit and thread engagement for a secure connection
• Helps maintain appliance alignment and safe operation

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread or part damage
• Turn off power and remove any access panels before working on electrical components

Fix uneven cooking or no convection heat with this blade hub assembly. Restores proper fan blade rotation in your range's convection system.

If your range oven or cooktop won't heat or cycles on and off, the daughter relay board may have failed. This control sub-board restores reliable switching.

This induction assembly replaces a damaged or nonworking induction surface element to restore induction heating on compatible cooktops. It provides the core induction coil and mounting needed for the element to generate heat for cookware. What it does:

• Houses the induction coil and associated hardware that create the electromagnetic field for induction cooking
• Restores heating when an induction zone fails to power or produce heat
• Resolves symptoms like no-heat, intermittent heating, or an induction zone that won't activate
• Works with the cooktop's control electronics to deliver localized heating to compatible cookware

• Disconnect power to the appliance at the breaker before servicing
• Handle the glass/ceramic surface carefully to avoid cracks or chips
• Reuse any verified mounting hardware; replace damaged fasteners as needed