Prd304ghu Parts

This push-button switch is a user-interface component that completes electrical circuits when pressed, restoring control to the affected function. It replaces a worn or failed switch to help regain reliable button response. What it does:

• Acts as the tactile electrical contact for a control or door function
• Restores responsiveness when a button no longer actuates the appliance
• Can stop intermittent operation caused by a worn or corroded switch contact
• Common symptom: controls or a specific function do not activate when the button is pressed

• One push-button switch as shown

• Disconnect power to the appliance before beginning any work
• Access may require removing a console or panel—keep track of fasteners and wire locations
• Disconnect wiring harness or terminals carefully; note connector orientation for reassembly
• Test the new switch with the power off using a multimeter continuity check before reassembly

This is a factory-style screw used to secure appliance panels and components for a reliable, low-profile hold. It replaces worn or missing fasteners to stop rattling and keep parts aligned during normal use. What it does:

• Secures trim, panels, brackets or small components in place
• Stops loose parts that can cause rattling or vibration noises
• Restores correct fit where a missing or damaged screw allows gaps
• Works as a direct replacement when the original fastener is lost or stripped

• One screw

• Disconnect power and water before servicing the appliance
• Start the screw by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly but avoid over-torquing to prevent stripping or part damage
• Keep removed hardware organized to ensure correct reassembly

This replacement tube routes water between internal components to maintain a sealed, reliable flow path. Swapping a cracked or hardened tube helps stop leaks and restore proper circulation and overall appliance performance.

• Carries water between internal components and maintains proper flow
• Helps keep connections watertight to prevent drips and pooling
• Replace if you see leaks, visible cracks, kinks, or a loose fit
• Restricted flow from a worn tube can contribute to reduced cleaning/performance

• Disconnect power and turn off the water supply before servicing; allow the unit to cool
• Remove access panels and keep towels handy for residual water
• Note the original routing and connection depth; transfer any fittings or clamps from the old tube if applicable
• Push the tube fully onto fittings and secure; run a test cycle and check carefully for leaks

This support mounting bracket secures internal components to the appliance chassis, restoring proper alignment and reducing movement that can cause noise or malfunction. Use it to replace a cracked or bent support that no longer holds parts firmly. What it does:

• Holds and stabilizes internal assemblies to prevent rubbing, vibration, or misalignment
• Restores proper component positioning that can stop intermittent noises or poor operation
• Prevents further wear by keeping parts securely fastened during use
• Works wherever the original support bracket has failed, bent, or broken

• Disconnect power and water before starting any repair
• Wear gloves to protect against sharp sheet-metal edges during removal/installation
• Typical installation requires basic hand tools; keep fasteners from the original part for fitment
• Follow the appliance service manual for disassembly and torque specifications

This fan motor drives the blower to move air through the appliance, restoring proper airflow for cooling or venting. Replacing a failing fan motor helps reduce overheating and improves overall performance. What it does:

• Spins the blower to circulate air for cooling, exhaust, or drying functions
• Restores proper airflow when the appliance has reduced ventilation
• Can stop or make noise if bearings are worn or the motor is failing
• Linked to overheating, reduced performance, or airflow-related error codes

• Disconnect power and any fuel lines before starting work
• Verify connector types and mounting points match the original motor prior to installation
• Handle the blower wheel and motor shaft carefully to avoid damage to the wheel or housing

This cover is an access panel that protects internal components and wiring while keeping the appliance looking finished. It helps prevent debris, moisture, and accidental contact with electrical parts for safer operation. What it does:

• Shields control and wiring areas from dust, food debris, and moisture
• Keeps moving parts and connectors securely covered to reduce snagging or accidental contact
• Stops rattling or vibration noise caused by a loose or damaged panel
• Visible damage or missing cover can expose wiring or components and cause operational issues

• One cover

• Disconnect power before attempting service to avoid shock or injury
• Remove screws or clips holding the old cover and lift straight off; retain fasteners if reusing
• Inspect surrounding seals and mounting tabs for damage; replace if cracked or broken
• Do not force or overtighten fasteners to avoid cracking the replacement cover

This heating element warms wash water and helps dry dishes by raising dishwasher tub temperature for improved cleaning and drying results. Replaces a failed or damaged tub heater to restore normal wash-cycle heating. What it does:

• Heats dishwasher wash and rinse water so detergents activate and soils break down
• Speeds or improves drying performance by raising internal temperature during final cycles
• Commonly replaced when dishwasher shows no heat, poor cleaning, or poor drying
• Works with dishwasher controls and sensors to cycle heat during selected programs

• Disconnect power and water supply before starting work to avoid shock or flooding
• Drain the dishwasher and remove the lower access panel to reach the element assembly
• Handle the element and wiring gently; replace any damaged seals or grommets to prevent leaks
• Test operation and check for leaks after reinstalling panels and restoring power

This hinge plate is a replacement door hinge support that helps secure and align the appliance door for smooth opening and closing. Restores proper door alignment and support when the original hinge plate is worn or damaged. What it does:

• Provides a mounting surface for the door hinge to keep the door aligned
• Helps prevent door sagging, misalignment, and uneven closing
• Restores stable door movement and reduces stress on hinge assemblies
• Works with the existing hinge hardware to maintain proper door operation

• Hinge plate

• Disconnect power to the appliance before attempting any repairs and remove any water supply if applicable
• Handle the door carefully during removal/installation to avoid dropping or damaging the door or trim
• Use basic hand tools; support the door while swapping hinge components to prevent injury or damage

A thermal fuse that cuts power when temperatures exceed safe limits, helping prevent overheating and related damage. Installs in the appliance's heater or control circuit to restore safe operation when replaced. What it does:

• Acts as a one-time overheat cutoff, opening the circuit if internal temperatures get too high
• Common symptom: appliance fails to heat or the heater element won't energize
• Common symptom: appliance has no power to the affected circuit or intermittent operation
• Restores overheat protection when replaced with the correct part number

• Always disconnect power (unplug or switch off breaker) before accessing the appliance
• Handle carefully and replace only with the exact part number to ensure correct temperature rating
• Verify wiring orientation and secure connections; some units require soldering or connector terminals

This replacement screw fastens appliance components to restore secure assembly and stable operation. It's a direct-fit fastener used where the original screw has stripped, corroded, or been lost. What it does:

• Secures panels, brackets, or small assemblies to prevent vibration and misalignment
• Restores proper fit where a damaged or missing screw causes rattling or loose parts
• Provides the correct fastening point for unchanged OEM mounting locations
• Works as a like-for-like replacement when the original screw is worn or missing

• Screw

• Turn off and unplug the appliance before beginning any repair
• Use the matched screwdriver or driver bit to avoid stripping the head
• Replace with the same thread engagement depth; do not force or overtighten
• Repair with the appropriate method before installing

This connector strip is the wire terminal block that joins appliance wiring harnesses for reliable electrical connections, helping restore power and control signal continuity. It's a direct-fit replacement when the original connector is damaged or burned. What it does:

• Provides a secure termination point for multiple wires so circuits can complete and controls receive power.
• Replaces corroded, loose, or burned terminals that cause intermittent power, no-heat or no-power issues.
• Maintains correct wiring alignment to prevent shorts or poor contact.
• Helps eliminate symptoms like a blank display, burners or elements not powering, or sporadic operation tied to a bad connection.

• Always disconnect power to the appliance (unplug or switch off breaker) before inspecting or replacing electrical parts.
• Verify wire locations and take a photo before removal to preserve proper wiring order.
• Replace only if terminals are visibly damaged, loose, or show signs of burning; secure all screws/nuts to factory tightness.