Prg304 Parts

The gas supply tube delivers gas from the main line to the range burners and is located behind or underneath the unit. Replace if you smell gas, notice uneven flame patterns, or if the tube shows signs of corrosion or damage during inspection.

This pilot light lens covers and diffuses the control-panel indicator lamp. Replace a cracked, missing, or discolored lens to restore clear visibility of the light, protect the lamp opening, and keep the panel looking finished.

• Covers and diffuses the indicator lamp on the control panel
• Helps protect the lamp opening from debris and accidental contact
• Restores a clean, finished appearance to the panel
• Replace if the lens is cracked, missing, loose, or discolored
• Can help when the indicator is hard to see even when lit

• Disconnect power to the appliance before servicing and allow surfaces to cool
• Access the indicator opening from the front or rear (varies by design) and remove any retainer or clips holding the old lens
• Note orientation and transfer any existing retainer or gasket if present
• Seat the new lens fully, reassemble, and test the indicator light

This rotary potentiometer converts shaft rotation into an electrical signal the control board can read, providing precise position feedback for user selections. Replace it if inputs become erratic, jump between settings, or the control stops responding.

• Provides rotary position feedback to the electronic control
• Enables accurate selection and adjustment of functions or setpoints
• Wear or damage can cause drifting, dead spots, or incorrect readings
• Intermittent or no response to input is a common failure symptom

• Disconnect power before servicing
• Access the control/console area to reach the component
• Note shaft orientation and any connector positions; transfer exactly to the new part
• Handle electronics with ESD care and verify smooth, full-range operation after reassembly

Fix a squealing or non-working oven fan with this gas range blower fan motor. Restores even heat distribution during baking and broiling cycles.

Fix an oven light that won't turn on or a self-clean cycle that won't start. This door switch monitors door position for safety and lighting.

Replace a seized or corroded burner gas tube when igniters stop working or burners won't light. Delivers gas safely to surface burners. DIY repair.

Stabilizing leveling foot for gas ranges. Provides balance and proper elevation. Replace if worn, broken, or missing to restore stability and positioning.

Fix overheating or loud fan noise in your gas range with this cooling fan motor. Protects electronics by circulating air to cool internal components.

Restore oven visibility with this complete light assembly. Replace when bulb won't light, lens is cracked, or socket is damaged. Verify fit with your model.

Support, hinge counter restores proper hinge support and door balance for a worn or damaged hinge assembly. This replacement helps the appliance door open and close smoothly and stay aligned for reliable everyday use. What it does:

• Provides structural support to the door hinge and helps counterbalance the door
• Stabilizes hinge movement to reduce sagging, binding, or uneven closing
• Helps the door latch and seal correctly by keeping the hinge alignment consistent
• Use when you notice door droop, difficulty latching, or irregular door motion

• Installation may require partial disassembly of the door or hinge assembly—refer to the OEM instructions for your model
• Disconnect power and turn off water supply before beginning any repair
• Inspect surrounding hinge components and fasteners; replace any damaged parts and test door operation after installation

Oven or burner won't adjust temperature correctly? This range potentiometer restores variable control. DIY-friendly repair, takes about 20 minutes.

Tube component for gas ranges. Installs in the burner assembly or manifold area. Replace if cracked, damaged, or leaking to restore proper operation.

This is a replacement appliance tube that routes water or air inside compatible Bosch appliances to maintain proper operation and prevent leaks. Durable plastic construction restores the original pathway for fluids or airflow. What it does:

• Replaces a worn, cracked, or damaged internal tube to stop leaks or seepage
• Restores proper routing of water or air so the appliance can operate as designed
• Helps eliminate symptoms like visible leaking, pooling, or unusual odors from trapped moisture
• Works as a direct-fit replacement where the original tube has failed or deteriorated

• One replacement tube

• Disconnect power and turn off the water supply before beginning any repairs
• Compare the new tube to the original for length, fittings, and orientation before installing
• Use proper clamps or retainers as required by the appliance; secure connections to prevent leaks

Replace a worn, broken, or missing gas range control knob. Restores safe operation and improves appearance. Fits directly onto the control shaft.

This indicator light illuminates to show when a burner or oven element is active or still hot. It is mounted on the control panel and provides a visual safety alert during and after cooking. Replace this part if the indicator fails to light up when a burner is on, stays lit continuously, or appears dim and flickering.

Oven light not working or flickering? This low-voltage transformer powers your range's interior lights. Restores proper oven lighting function.