Prg340gh/20 Parts

If your gas burner won't ignite or clicks continuously without lighting, the spark module may have failed. This electronic component generates sparks reliably.

This rotary potentiometer converts shaft rotation into an electrical signal the control board can read, providing precise position feedback for user selections. Replace it if inputs become erratic, jump between settings, or the control stops responding.

• Provides rotary position feedback to the electronic control
• Enables accurate selection and adjustment of functions or setpoints
• Wear or damage can cause drifting, dead spots, or incorrect readings
• Intermittent or no response to input is a common failure symptom

• Disconnect power before servicing
• Access the control/console area to reach the component
• Note shaft orientation and any connector positions; transfer exactly to the new part
• Handle electronics with ESD care and verify smooth, full-range operation after reassembly

Fix a squealing or non-working oven fan with this gas range blower fan motor. Restores even heat distribution during baking and broiling cycles.

This electronic PC board is the appliance's main control, processing inputs and directing power to components so cycles run correctly. Replacing a failed board can restore normal operation when the unit is dead, won't start, or stops mid-cycle.

• Interprets user inputs and sensor feedback to execute programmed cycles
• Switches relays to power motors, valves, heaters, and other loads as required
• Manages timing, temperature, and safety logic for consistent performance
• Typical failure symptoms: no power/won't start, unresponsive or erratic controls, cycles ending prematurely, recurring error codes

• Disconnect power before servicing; verify power is off with a meter
• Use ESD protection; handle the board by the edges to avoid static damage
• Move connectors one at a time to identical positions on the new board to prevent miswiring
• Some models require service-mode setup or calibration after installation—follow your model's service documentation

Fix burners that won't light with this range igniter. Includes spring and clip for secure installation. Compatible with multiple range models.

Fix an oven light that won't turn on or a self-clean cycle that won't start. This door switch monitors door position for safety and lighting.

Fixes no spark at burners or oven not lighting issues. This ignition module generates the high-voltage spark needed to ignite gas at electrodes.

Secures panels and internal components in gas ranges. Replace this fastener if missing, rusted, or stripped to restore proper fit and alignment.

This is a wire oven rack designed to glide smoothly in and out of the oven cavity on built-in rail supports. It provides a sturdy surface for holding cookware and bakeware at various positions inside the oven. Replace this shelf if it is warped, rusted, has broken wires, or no longer glides properly on the oven rails.

This replacement screw secures appliance components and panels in their proper position. Replacing worn, stripped, or missing hardware restores a tight fit, reduces vibration or rattles, and helps maintain safe, reliable operation per the manufacturer's design. What it does:

• Fastens panels, brackets, or assemblies where specified in the model's parts diagram
• Replaces missing, rusted, or stripped hardware
• Helps eliminate looseness, rattling, or vibration
• Restores secure alignment of mounted components

• 1 screw

• Disconnect power and shut off water/gas before servicing.
• Verify the exact location in your model's parts diagram and replace screws one at a time to maintain alignment.
• Use the correct driver/bit; start threads by hand to avoid cross-threading and do not overtighten.
• Inspect mating holes/clips for damage; repair or replace related hardware if threads are compromised.

Replace a seized or corroded burner gas tube when igniters stop working or burners won't light. Delivers gas safely to surface burners. DIY repair.

This compression sleeve forms the sealing ring for a 5/16-inch tubing compression joint, restoring a watertight connection when used with a matching compression nut and fitting. Ideal for stopping leaks and restoring reliable water lines. What it does:

• Creates the compression seal on 5/16" tubing when installed with a compatible compression nut and fitting.
• Stops leaks or drips at compression-style water connections.
• Used on appliance water lines (ice makers, water inlets) and other 5/16" tubing joints.
• Replaces worn or damaged sleeves that fail to hold a tight seal.

• Shut off the water supply and relieve pressure before working on water lines.
• Inspect and cut tubing squarely; slide the sleeve onto the tube before threading the compression nut and fitting.
• Tighten the compression nut per the fitting manufacturer's instructions and check the joint for leaks.
• Replace the sleeve if damaged or deformed.

Stabilizing leveling foot for gas ranges. Provides balance and proper elevation. Replace if worn, broken, or missing to restore stability and positioning.

Fix overheating or loud fan noise in your gas range with this cooling fan motor. Protects electronics by circulating air to cool internal components.

If one burner won't spark but others work, the igniter switch may have failed. This part sends the spark signal to ignite gas burners reliably.

Restore oven visibility with this complete light assembly. Replace when bulb won't light, lens is cracked, or socket is damaged. Verify fit with your model.