Prg364edg06 Parts

A Trident-style surface burner head that directs gas to the cooktop burner for an even, controlled flame. Replaces a worn or damaged burner head to restore consistent heating and safe operation. What it does:

• Directs and shapes the gas flame for proper cooking heat
• Restores even flame pattern when the original burner is warped or clogged
• Helps eliminate weak or irregular flames caused by damaged ports
• Works with the burner base and cap to maintain stable ignition

• Turn off the appliance and shut off gas/electric power before servicing
• Remove grates and burner cap, then replace the burner head; reassemble in reverse order
• Clean mating surfaces of debris or corrosion before installation for proper fit

This grille for pan is a replacement trim piece that restores proper airflow and appearance around the appliance pan. It helps keep the pan area protected and looking finished after repair. What it does:

• Covers and ventilates the pan opening to help direct airflow and prevent debris entry
• Replaces a cracked, warped, or missing grille to restore fit and finish
• Helps eliminate rattling or rubbing caused by a damaged trim piece
• Matches OEM fit so it installs cleanly with the original mounting points

• Install requires removal of the surrounding trim or access panel; follow your appliance manual
• Handle carefully to avoid scratching the finish; use non-marring tools as needed
• Disconnect power to the appliance before working in the service area
• Replace damaged clips or screws with OEM fasteners for secure fit

This push-button switch is a user-interface component that completes electrical circuits when pressed, restoring control to the affected function. It replaces a worn or failed switch to help regain reliable button response. What it does:

• Acts as the tactile electrical contact for a control or door function
• Restores responsiveness when a button no longer actuates the appliance
• Can stop intermittent operation caused by a worn or corroded switch contact
• Common symptom: controls or a specific function do not activate when the button is pressed

• One push-button switch as shown

• Disconnect power to the appliance before beginning any work
• Access may require removing a console or panel—keep track of fasteners and wire locations
• Disconnect wiring harness or terminals carefully; note connector orientation for reassembly
• Test the new switch with the power off using a multimeter continuity check before reassembly

The Surface Burner Holder is an OEM part for Bosch ranges and cooktops. It serves to securely mount and support both the surface burner assembly and gas orifices in place on the cooktop. 

Causes of a faulty or damaged burner and orifice holder can include wear from heavy daily cooking demands, broken mounting tabs due to impact or dropped cookware, or corrosion affecting the burner and orifice fittings over many years.

Symptoms of failure include:

• Gas leaks at burner and/or orifice connections
• Difficulty achieving proper burner ignition
• Burners that are loose, wobbly or unstable during cooking
• Inability to effectively seal the burner and orifice assembly into position

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Ignition Device is an OEM part for Bosch ranges and ovens. Located near each gas burner, the ignition device provides the critical spark needed to light the burners during startup. 

Causes of a bad ignition device can include wear from prolonged use over many years. Mineral buildup or debris accumulation may also prevent the spark from jumping across.

Symptoms of a bad ignition device include:

• Burners failing to light or staying lit
• Repeated attempts needed to ignite the gas  
• Inconsistent flame heights or burner performance
• Fault codes or error messages displayed

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models. 

This gas pressure regulator controls and stabilizes incoming supply pressure to the appliance manifold, helping ensure consistent burner flames and reliable ignition. Replace if the original regulator is sticking or no longer maintaining correct pressure.

• Regulates incoming gas to the appliance's rated manifold pressure
• Helps maintain even flame height and proper combustion
• Supports reliable burner ignition and reduces flame-out from pressure swings
• Common symptoms include weak or uneven flames, yellow tipping, burners not lighting or not staying lit, or flames that are too high

• Disconnect electrical power and shut off the gas supply before servicing
• Observe the flow-direction arrow; install with outlet toward the appliance manifold
• Use approved gas-rated thread sealant on male threads only and leak-test all joints with a non-corrosive solution after installation

This OEM replacement part is a motor assembly for ovens. The motor assembly is the main motor that powers the oven fan which is responsible for maintaining and adjusting the temperature in an oven. If the oven is no longer heating properly, turning on, or maintaining temperature, then the motor assembly will need to be replaced.To replace this part, make sure that the oven is unplugged. After it has been powered off, proceed to pull the oven out and away from the wall. Once moved, uninstall the back panel of the oven by removing the panel's mounting screws. After detaching the back panel, locate the motor housing on the back of the oven. Unthread the screws that hold the housing in place. Once removed, locate the mounting brackets that hold the motor in place and remove the screws that attach to the motor. Pull the old motor out of its place and install the new motor. Reinstall the back panel and restore power to the appliance.This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador brand ovens.

Restore confident control of your appliance with this replacement control knob. It slides onto the control shaft to provide a secure, accurate grip so you can easily select settings when the original knob is cracked, stripped, or missing. What it does:

• Attaches to the control shaft to select temperature, cycle, or power settings
• Restores positive engagement and smooth turning of the control
• Helps resolve a loose, wobbly, or slipping selector
• Replaces knobs that are cracked, broken, or won't stay on

• One control knob

• Disconnect power; for gas appliances, also shut off the gas supply before servicing
• Pull the old knob straight off the shaft; if your model uses a set screw or clip, loosen/remove it first
• Align the new knob with the shaft and press on firmly; retighten any set screw if present
• Test operation to ensure the knob engages and turns the control smoothly