Prg366 Propane Parts

This support is a genuine replacement that secures and aligns an associated component inside the appliance, keeping it stable and operating as intended. Replacing a damaged support helps restore proper fit, reduce vibration, and prevent premature wear.

• Provides structural mounting and support for the designated assembly
• Maintains correct alignment and spacing of parts
• Helps prevent wobble, rattling, or rubbing during operation
• Symptoms can include loose or sagging parts, misalignment, unusual noise, or visible cracks in the original support

• Disconnect power; shut off water supply before servicing
• Refer to your model's parts diagram to orientation and fastener locations
• Transfer any screws/clips from the original part if new hardware is not supplied
• Tighten fasteners evenly and avoid overtightening plastic components

This is a replacement rotary potentiometer for appliance control panels—provides smooth variable input for temperature/speed/setting adjustments so the appliance responds correctly to user control changes. What it does:

• Acts as the variable resistor that the control knob uses to set temperature, speed, or other settings
• Restores accurate user input when original control becomes intermittent, jumps, or fails to change settings smoothly
• Helps eliminate erratic readouts or unresponsive knob adjustments linked to a worn or faulty potentiometer
• Works as the electronic interface between the knob and the appliance control board

• Disconnect power before accessing internal control panel to avoid shock or damage
• Handle PCB and connector pins carefully; avoid bending leads or contaminating contacts
• Replace only with the exact part number listed and reassemble panel alignment before testing

This Jet is the small spray nozzle that directs a focused stream of water inside the dishwasher's wash system. Replacing a clogged or damaged jet helps restore proper spray coverage, wash pressure, and overall cleaning performance.

• Directs and meters water flow within the wash system
• Helps maintain spray arm/wash zone pressure and coverage
• Replace if clogged with mineral deposits or physically damaged
• Symptoms include poor cleaning, weak spray, unusual wash noise, or leaks near the nozzle

• Disconnect power and shut off the water supply before servicing
• Access the nozzle location and note its orientation and any seals/clips
• Clean mating surfaces; transfer any reusable seal/clip if present
• Seat and lock the jet fully; run a test cycle and check for leaks

This cap covers and protects its mating opening or fastener on the appliance, helping keep debris and moisture out while restoring a clean, finished look. Replace a cracked or missing cap to maintain proper protection and appearance. What it does:

• Provides a finished cover for an opening or fastener
• Helps prevent dust, debris, and moisture intrusion
• Supports proper fit of the assembly it mates with
• Common signs include a cracked, loose, or missing cap; exposed hardware; or difficulty securing the area

• 1 cap

• Disconnect power; shut off water or gas to the appliance before servicing
• Note the original cap's orientation; release any tabs or threads to remove
• Clean the mating area; press or thread the new cap on until fully seated—do not overtighten
• The cap is secure and that surrounding components operate normally

The Repair Set is an OEM part designed specifically for Bosch range ovens that includes the necessary parts to repair your oven door hinges. It is responsible for maintaining the proper alignment and stability of the door, allowing for the smooth opening and closing of your oven door.

A bad oven door hinge can occur due to wear and tear, accidental damage, or improper handling. Signs of faulty hinges include a loose or wobbly oven door, difficulty in opening or closing, or the door not staying securely in place during operation.

Symptoms of bad oven door hinges include:

• A loose door that does not close properly
• Difficulty in opening or closing the door smoothly
• The door not staying securely in place when in use

Replace your worn-out or damaged oven door hinges with this genuine OEM Bosch part to restore your oven door. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

The Knob is an OEM part for Bosch ranges. This knob allows users to control the temperature and cooking settings on their stove or oven effectively.  

Causes of a bad knob can include prolonged exposure to heat, which can cause the material to degrade, accidental damage, or normal wear and tear that leads to cracking or breaking. 

Symptoms of a bad knob include:

• Difficulty in turning or adjusting the knob
• The knob feeling loose or falling off
• Visual signs of damage such as cracks or melting
• Failure to engage the stove or oven controls properly

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Rack is an OEM component specifically designed for premium Bosch wall ovens and ranges. Comprised of heavy-duty metal racks powder coated for durability, they facilitate the versatile cooking of multiple dishes simultaneously. Adjustable rack positions maximize oven capacity.

Causes of failure can include warping or bending from years of high-temperature exposure. Scratches or surface deterioration from aggressive cleaning tools may compromise rack integrity over time as well.

Symptoms include:

• Inability to securely hold bakeware during cooking  
• Misaligned or slanted racks presenting hazards
• Surface flaking compromising hygienic cooking
• Limited rack positions reducing oven versatility

Replacing with this genuine Bosch rack restores multi-level cooking. Compatible with Thermador, Dacor, and Gaggenau.
 

This socket is an electrical connector used to join wiring or plug-in components, restoring a secure connection for reliable appliance operation. It replaces a worn or damaged socket to help prevent intermittent power or component failure. What it does:

• Provides a secure electrical connection between wiring and the appliance component
• Restores proper contact when a loose, corroded, or broken socket causes intermittent operation
• Helps prevent arcing or poor connections that can lead to component failure
• Used where a plug-in or push-fit electrical connection is required

• One socket

• Disconnect power to the appliance before inspecting or replacing the socket
• Replace only with the exact socket type specified for your appliance

Support, hinge counter restores proper hinge support and door balance for a worn or damaged hinge assembly. This replacement helps the appliance door open and close smoothly and stay aligned for reliable everyday use. What it does:

• Provides structural support to the door hinge and helps counterbalance the door
• Stabilizes hinge movement to reduce sagging, binding, or uneven closing
• Helps the door latch and seal correctly by keeping the hinge alignment consistent
• Use when you notice door droop, difficulty latching, or irregular door motion

• Installation may require partial disassembly of the door or hinge assembly—refer to the OEM instructions for your model
• Disconnect power and turn off water supply before beginning any repair
• Inspect surrounding hinge components and fasteners; replace any damaged parts and test door operation after installation

This transformer supplies the low-voltage power needed for an oven's interior lights so bulbs operate reliably. It restores proper lighting and helps stop flicker or complete loss of oven lamp function. What it does:

• Converts the oven's supply to the low-voltage output required by interior lamp circuits.
• Restores steady lamp operation when lights fail to come on or flicker.
• Works with the oven's light switch and control circuitry to deliver consistent voltage.
• Helps prevent false diagnostics caused by intermittent lamp power.

• One oven light transformer.

• Disconnect all power to the appliance before starting any repair.
• Accessible behind the control panel or chassis; remove panels carefully to reach the transformer.
• Note wire locations and secure all connectors; use proper wire connectors and strain relief.

This display is the user interface module that shows cycle status, settings and error indicators so you can read and control the appliance from the front panel. It restores visible feedback and menu information for normal operation. What it does

• Provides the visible display for cycle progress, timers and selected options
• Shows error codes and status messages to help identify issues
• Works with the appliance control board to update settings and user inputs
• Restores readable display after a failed or cracked panel

• Disconnect power to the appliance before starting work to avoid shock or damage
• Replacement typically requires removal of the front control or console panel; handle the display lens and ribbon connectors carefully
• Keep screws and small fasteners organized for reassembly

Replacement water inlet valve that controls an appliance's incoming water flow for reliable fill and cycle operation. Replacing a faulty valve can stop no-fill, slow-fill, or continuous-fill issues and restore normal performance. What it does:

• Opens and closes to regulate water entering the appliance during fill cycles.
• Helps ensure correct water levels for proper washing or rinsing.
• Common symptom fixer for appliances that won't fill, fill slowly, or keep filling.
• May cause visible leaks at the valve or trigger fill-related fault behavior if failed.

• Turn off power and shut off the water supply before starting any work.
• Open a cycle or relieve pressure to drain residual water before removing the old valve.
• Inspect and replace any worn seals or inlet hoses when installing the new valve.
• Follow the appliance service manual for specific removal/installation steps.

This is a replacement control knob that restores safe, easy control of a cooktop or oven function. It provides a secure grip and clear position indication so you can set heat or cycle settings precisely. What it does:

• Fits over the control shaft to allow turning temperature/settings without touching the control stem
• Replaces cracked, stripped, missing, or hard-to-turn knobs
• Restores clear detent positions for accurate setting selection
• Helps prevent accidental changes by seating securely on the shaft

• Before servicing, disconnect power to the appliance and shut off gas supply if applicable
• Pull old knob straight off the control shaft; align replacement onto the shaft and push until fully seated
• Do not use excessive force; inspect the control stem for damage before installation

This ignition cable connects the stove's spark electrode to the ignition system so burners ignite reliably. It replaces a damaged or degraded lead to restore spark delivery and consistent lighting. What it does:

• Transfers ignition voltage from the module to the burner electrode so sparks form at the burner
• Helps stop intermittent or no-spark symptoms when the wire is cracked or corroded
• Prevents arcing caused by insulation damage or improper routing
• Restores normal ignition behavior when the original cable is worn or burned

• One ignition cable

• Disconnect power and turn off gas supply before starting any service
• Inspect routing and connectors; replace only if the wire or insulation is damaged
• Keep the cable away from high-heat areas and sharp edges to prevent future damage

This 1/4" gas supply tubing connects the appliance's gas line to the valve, providing a secure path for fuel so the unit can ignite and operate safely. Use when tubing is damaged, leaking, or replaced during valve service. What it does:

• Channels natural gas/LP from the household supply to the appliance valve
• Replaces cracked, corroded, or bent tubing that can cause leaks
• Helps stop symptoms like a persistent gas smell, failure to ignite, or intermittent burner operation
• Works with the appliance's inlet and control valve fittings to maintain proper gas flow

• Turn off the gas supply and electrical power before starting work
• Use approved fittings, thread sealant rated for gas, and test all connections for leaks after installation
• Do not modify or reuse damaged tubing; replace with exact-fit parts