Prg366wh/02 Parts

This pilot light lens covers and diffuses the control-panel indicator lamp. Replace a cracked, missing, or discolored lens to restore clear visibility of the light, protect the lamp opening, and keep the panel looking finished.

• Covers and diffuses the indicator lamp on the control panel
• Helps protect the lamp opening from debris and accidental contact
• Restores a clean, finished appearance to the panel
• Replace if the lens is cracked, missing, loose, or discolored
• Can help when the indicator is hard to see even when lit

• Disconnect power to the appliance before servicing and allow surfaces to cool
• Access the indicator opening from the front or rear (varies by design) and remove any retainer or clips holding the old lens
• Note orientation and transfer any existing retainer or gasket if present
• Seat the new lens fully, reassemble, and test the indicator light

Grill grid sits in the grill cavity to allow direct heat cooking and collect drippings. Replace if warped, cracked, or damaged. Confirm fit with your model.

The gas supply tube delivers gas from the main line to the range burners and is located behind or underneath the unit. Replace if you smell gas, notice uneven flame patterns, or if the tube shows signs of corrosion or damage during inspection.

This high-limit thermostat is a safety device that monitors the oven's internal temperature and cuts power to the heating element if the temperature exceeds a safe threshold. It helps prevent overheating and potential fire hazards. Replace this part if your oven shuts off unexpectedly, fails to heat at all, or triggers error codes related to excessive temperature.

Fix a squealing or non-working oven fan with this gas range blower fan motor. Restores even heat distribution during baking and broiling cycles.

This rotary potentiometer converts shaft rotation into an electrical signal the control board can read, providing precise position feedback for user selections. Replace it if inputs become erratic, jump between settings, or the control stops responding.

• Provides rotary position feedback to the electronic control
• Enables accurate selection and adjustment of functions or setpoints
• Wear or damage can cause drifting, dead spots, or incorrect readings
• Intermittent or no response to input is a common failure symptom

• Disconnect power before servicing
• Access the control/console area to reach the component
• Note shaft orientation and any connector positions; transfer exactly to the new part
• Handle electronics with ESD care and verify smooth, full-range operation after reassembly

This electronic PC board is the appliance's main control, processing inputs and directing power to components so cycles run correctly. Replacing a failed board can restore normal operation when the unit is dead, won't start, or stops mid-cycle.

• Interprets user inputs and sensor feedback to execute programmed cycles
• Switches relays to power motors, valves, heaters, and other loads as required
• Manages timing, temperature, and safety logic for consistent performance
• Typical failure symptoms: no power/won't start, unresponsive or erratic controls, cycles ending prematurely, recurring error codes

• Disconnect power before servicing; verify power is off with a meter
• Use ESD protection; handle the board by the edges to avoid static damage
• Move connectors one at a time to identical positions on the new board to prevent miswiring
• Some models require service-mode setup or calibration after installation—follow your model's service documentation

This control unit is the central electronic board that manages your appliance's functions and cycles. Replacing a failed module can restore responsive controls and reliable operation when the machine won't start, stops mid-cycle, or shows repeated error codes. What it does:

• Directs timing and power to components such as motors, pumps, valves, or heaters
• Interprets inputs from the user controls and sensors to run the selected program
• Coordinates safety interlocks and built-in diagnostic routines
• Common failure symptoms include no start, unresponsive controls, random shutdowns, or persistent error codes

• 1 control unit

• Disconnect power (unplug or switch off the breaker) before servicing; shut off water supply if applicable
• Handle the board with ESD precautions; avoid touching components and contacts
• Photograph wiring and move connectors one at a time to the new board to maintain placement
• Ensure all harnesses are fully seated and the module is secured; restore power and run model-specific tests per the service documentation

Replacement drip pan for gas cooktops and ranges. Sits beneath burners to catch spills and protect the cooktop base. Replace if cracked, warped, or rusted.

If your gas burner won't ignite or clicks continuously without lighting, the spark module may have failed. This electronic component generates sparks reliably.

Stabilizing leveling foot for gas ranges. Provides balance and proper elevation. Replace if worn, broken, or missing to restore stability and positioning.

Gas supply tube connects gas line to range burners. Replace if cracked, kinked, damaged, or leaking. Installs between supply valve and burner assembly.

Secures panels and internal components in gas ranges. Replace this fastener if missing, rusted, or stripped to restore proper fit and alignment.

Restore oven visibility with this complete light assembly. Replace when bulb won't light, lens is cracked, or socket is damaged. Verify fit with your model.

This is an indicator light or display component mounted on the range's control panel that provides visual feedback about oven or burner status. It lets you know when a heating element is active or when the oven has reached the set temperature. Replace this part if the indicator fails to illuminate, flickers intermittently, or displays incorrect information.

Replace a seized or corroded burner gas tube when igniters stop working or burners won't light. Delivers gas safely to surface burners. DIY repair.