Prg486edg/09 Parts

The Heater Element Range is an OEM component for Bosch electric ranges. It is responsible for generating precise heat to cook foods and bake consistently.

Causes of a bad element range include scaling or mineral deposits from repeated cleanings that interfere with heat transfer. Broken coils from rough handling can also disrupt heat output.

Symptoms of a bad heater element range include:

• Long preheat times unable to reach desired heat  
• Burnt exteriors but raw interiors when baking
• Disabled or reluctant-to-heat oven and broiler functions
• Hot and cold spots causing inconsistent results

This OEM Bosch part can also be used on Thermador and Gaggenau appliances.

Oven light not working or flickering? This low-voltage transformer powers your range's interior lights. Restores proper oven lighting function.

This two-way valve controls water flow into the appliance, restoring proper fill and cycle operation when the valve fails. Direct-fit replacement designed to match OEM function and restore reliable water routing. What it does:

• Opens and closes to direct water to the correct circuit during wash/fill cycles
• Stops water flow when the appliance is off or when a fill cycle is complete
• Commonly replaced for symptoms like no fill, continuous filling, or leaking at the valve
• Provides the solenoid-actuated shutoff function used by the appliance control system

• Disconnect power and water supply before starting; verify the appliance is completely de-energized
• Drain remaining water and take photos of hose/electrical connections before removal to aid reassembly
• Use hand tools and avoid overtightening fittings to prevent damage; inspect inlet hoses and seals while replacing

Oven lamp assembly provides interior lighting for viewing food during cooking. Replace when bulb burns out or housing cracks. Verify fit with your model.

Replace your cracked or faded control panel insert trim to restore appearance and proper button alignment. Fits into the control area for a clean look.

Burner housing for gas ranges. Surrounds and supports the burner assembly on the cooktop. Replace if cracked, damaged, or missing to restore appearance.

Fix a range door that won't stay open or closes too hard with this tension spring. Restores proper door balance and smooth operation. Simple DIY fix.

Small hardware pin that secures or pivots components in gas ranges and cooktops. Replace if worn, missing, or broken to restore proper alignment.

Gas range burner tube that connects the gas valve to the burner assembly. Replace if tube is cracked, corroded, or causing improper gas flow.

Fix unresponsive range controls with this push-button switch. Restores button function when controls stop working. Simple replacement for worn switches.

If your gas range broiler won't ignite or stays on continuously, the broil solenoid controls gas flow to the broil burner and may need replacement.

Replace your range control knob if the original is cracked, broken, worn, or missing. This knob installs on the control panel to operate burners or oven.

This is an overflow drip tray designed to catch liquid spills and boil-overs inside the range or oven cavity, preventing them from reaching internal components. It sits beneath the cooking area and collects excess moisture or grease. Replace this tray if it is cracked, warped, corroded, or no longer sitting flat, which could allow liquids to leak onto electrical parts below.

Fix weak or uneven flames on your gas range cooktop. This burner head restores proper gas distribution for consistent heating and safe operation.

This grille for pan is a replacement trim piece that restores proper airflow and appearance around the appliance pan. It helps keep the pan area protected and looking finished after repair. What it does:

• Covers and ventilates the pan opening to help direct airflow and prevent debris entry
• Replaces a cracked, warped, or missing grille to restore fit and finish
• Helps eliminate rattling or rubbing caused by a damaged trim piece
• Matches OEM fit so it installs cleanly with the original mounting points

• Install requires removal of the surrounding trim or access panel; follow your appliance manual
• Handle carefully to avoid scratching the finish; use non-marring tools as needed
• Disconnect power to the appliance before working in the service area
• Replace damaged clips or screws with OEM fasteners for secure fit

This pressure regulator controls and stabilizes incoming water pressure to the appliance, helping maintain consistent operation and protect internal valves and seals. Fits systems that use a 3/4 inch inlet regulator. What it does:

• Reduces high incoming water pressure to a safe, steady level for the appliance
• Prevents pressure-related leaks, valve chatter, and premature wear on seals
• Helps maintain consistent water flow for reliable cycles and operation
• Commonly replaced when irregular pressure, humming valves, or water leaks occur

• One pressure regulator (3/4 in.)

• Turn off water supply and power to the appliance before starting; relieve system pressure first
• Inspect connection fittings and seals; use appropriate thread sealant if required by the OEM
• Tighten to manufacturer torque recommendations and check for leaks after restoring water