Prg486jdg/07 Parts

This ignition cable connects the stove's spark electrode to the ignition system so burners ignite reliably. It replaces a damaged or degraded lead to restore spark delivery and consistent lighting. What it does:

• Transfers ignition voltage from the module to the burner electrode so sparks form at the burner
• Helps stop intermittent or no-spark symptoms when the wire is cracked or corroded
• Prevents arcing caused by insulation damage or improper routing
• Restores normal ignition behavior when the original cable is worn or burned

• One ignition cable

• Disconnect power and turn off gas supply before starting any service
• Inspect routing and connectors; replace only if the wire or insulation is damaged
• Keep the cable away from high-heat areas and sharp edges to prevent future damage

This 1/4" gas supply tubing connects the appliance's gas line to the valve, providing a secure path for fuel so the unit can ignite and operate safely. Use when tubing is damaged, leaking, or replaced during valve service. What it does:

• Channels natural gas/LP from the household supply to the appliance valve
• Replaces cracked, corroded, or bent tubing that can cause leaks
• Helps stop symptoms like a persistent gas smell, failure to ignite, or intermittent burner operation
• Works with the appliance's inlet and control valve fittings to maintain proper gas flow

• Turn off the gas supply and electrical power before starting work
• Use approved fittings, thread sealant rated for gas, and test all connections for leaks after installation
• Do not modify or reuse damaged tubing; replace with exact-fit parts

Support, hinge counter restores proper hinge support and door balance for a worn or damaged hinge assembly. This replacement helps the appliance door open and close smoothly and stay aligned for reliable everyday use. What it does:

• Provides structural support to the door hinge and helps counterbalance the door
• Stabilizes hinge movement to reduce sagging, binding, or uneven closing
• Helps the door latch and seal correctly by keeping the hinge alignment consistent
• Use when you notice door droop, difficulty latching, or irregular door motion

• Installation may require partial disassembly of the door or hinge assembly—refer to the OEM instructions for your model
• Disconnect power and turn off water supply before beginning any repair
• Inspect surrounding hinge components and fasteners; replace any damaged parts and test door operation after installation

This control knob replaces a worn, broken, or missing stove/oven knob to restore safe, reliable control and improve the appliance's appearance. It fits directly onto the control shaft for a secure, tactile grip. What it does

• Replaces a damaged or missing control knob so you can set burners or oven functions accurately
• Provides a solid grip and clear pointer for selecting settings
• Stops slipping or spinning caused by a cracked or worn knob
• Helps restore normal operation when the original knob is loose or won't stay engaged

• Disconnect power (unplug appliance or switch off breaker) before servicing to avoid electrical or burn hazards.
• Pull the old knob straight off the control shaft; no special tools typically required.
• Align the new knob's splines with the shaft and push straight on until fully seated.
• Do not force the knob; if it does not fit, check shaft shape and orientation before applying pressure.

The Heater Element Range is an OEM component for Bosch electric ranges. It is responsible for generating precise heat to cook foods and bake consistently.

Causes of a bad element range include scaling or mineral deposits from repeated cleanings that interfere with heat transfer. Broken coils from rough handling can also disrupt heat output.

Symptoms of a bad heater element range include:

• Long preheat times unable to reach desired heat  
• Burnt exteriors but raw interiors when baking
• Disabled or reluctant-to-heat oven and broiler functions
• Hot and cold spots causing inconsistent results

This OEM Bosch part can also be used on Thermador and Gaggenau appliances.

This two-way valve controls water flow into the appliance, restoring proper fill and cycle operation when the valve fails. Direct-fit replacement designed to match OEM function and restore reliable water routing. What it does:

• Opens and closes to direct water to the correct circuit during wash/fill cycles
• Stops water flow when the appliance is off or when a fill cycle is complete
• Commonly replaced for symptoms like no fill, continuous filling, or leaking at the valve
• Provides the solenoid-actuated shutoff function used by the appliance control system

• Disconnect power and water supply before starting; verify the appliance is completely de-energized
• Drain remaining water and take photos of hose/electrical connections before removal to aid reassembly
• Use hand tools and avoid overtightening fittings to prevent damage; inspect inlet hoses and seals while replacing

This electronic control board manages a dishwasher's core functions, coordinating cycles, timing, and user interface so the appliance runs the selected wash program reliably. Replacing a failed control restores normal operation and responds to user inputs. What it does:

• Acts as the dishwasher's main logic board to control cycle selection, timing, and sequence
• Manages signals for fill, wash, drain, and pump operation
• Interfaces with the front panel and displays to process user inputs
• Prevents or causes missed cycles, unresponsive controls, or erratic behavior when faulty

• Disconnect all power to the appliance before starting—risk of electric shock
• Handle the board by edges and avoid static discharge; use an anti-static wrist strap if available
• Verify connector orientation and secure all wiring; do not force connectors

Replacement water inlet valve that controls an appliance's incoming water flow for reliable fill and cycle operation. Replacing a faulty valve can stop no-fill, slow-fill, or continuous-fill issues and restore normal performance. What it does:

• Opens and closes to regulate water entering the appliance during fill cycles.
• Helps ensure correct water levels for proper washing or rinsing.
• Common symptom fixer for appliances that won't fill, fill slowly, or keep filling.
• May cause visible leaks at the valve or trigger fill-related fault behavior if failed.

• Turn off power and shut off the water supply before starting any work.
• Open a cycle or relieve pressure to drain residual water before removing the old valve.
• Inspect and replace any worn seals or inlet hoses when installing the new valve.
• Follow the appliance service manual for specific removal/installation steps.

This panel insert replaces a damaged or missing control-panel trim piece to restore the front appearance and support proper button alignment and sealing. It fits into the appliance's control area for a clean, finished look. What it does:

• Replaces cracked, faded, or otherwise damaged control-panel insert pieces
• Restores cosmetic finish and proper fit for control buttons and overlays
• Helps maintain a sealed control area against moisture and debris
• Prevents loose or misaligned panel edges that can interfere with operation

• Disconnect power to the appliance before starting any repair
• Handle edges carefully to avoid scratching or cutting; wear gloves if needed
• May require removal of the outer door or control bezel—use proper tools and follow the service manual

The Lamp is an OEM part for Bosch ranges and ovens. The range lamp provides visibility when viewing food through the oven window or checking on items cooking on the stove.

Causes of a bad range lamp can include normal wear and tear over time, as well as accidental damage from impact or handle mishandling.

Symptoms of a bad range lamp include:

• Diminished light that does not adequately illuminate the cooking space
• Flickering or unstable illumination
• A burned out or broken bulb

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This panel insert is the replacement control-panel trim that restores a clean, finished look and protects the console area from scratches and wear. It fits into the console to cover and support the control surface. What it does:

• Replaces cracked, scratched, or cosmetically damaged control-panel trim
• Protects underlying buttons and electronics from everyday wear and spills
• Restores a uniform appearance to the appliance front for a like-new finish
• Helps ensure control buttons and labels sit correctly in the console area

• Disconnect power to the appliance before starting any repair
• Access may require removal of the console or outer door; follow the OEM service manual
• Handle the insert carefully to avoid scratches; align tabs/clips before applying pressure

This OEM replacement pin is a small hardware fastener used to secure or pivot mating components within the appliance. Replacing a worn or missing pin restores proper alignment and reliable movement of the affected part or linkage.

• Serves as an axle/retainer for hinges, brackets, or linkages
• Maintains alignment of moving parts to reduce wobble or binding
• When bent, worn, or missing, you may notice looseness, rattling, misalignment, or difficulty opening/closing related components
• Direct-fit OEM replacement for the specified application

• Disconnect electrical power and shut off water or gas before servicing
• Support the component being serviced to prevent strain or damage during removal/installation
• Note the original orientation and retain any washers, clips, or spacers for transfer to the new pin
• Inspect mating holes/bushings; replace related worn parts to ensure proper fit and operation

This replacement screw secures appliance panels and components in their proper position. Installing this screw restores a solid, factory fit and helps prevent vibration and misalignment.

• Fastens panels, brackets, or internal parts to the appliance chassis
• Maintains alignment to reduce vibration and rattling noises
• Replaces missing, rusty, or stripped hardware
• Typical symptoms include loose panels, gaps, rattles, or a screw that won't tighten

• Disconnect power (and shut off water or gas, if applicable) before servicing
• Support panels and watch for sharp edges and pinch points
• Use the correct driver size/type for your model to avoid stripping
• Start threads by hand to prevent cross-threading; tighten snugly without over-torquing

This grille for pan is a replacement trim piece that restores proper airflow and appearance around the appliance pan. It helps keep the pan area protected and looking finished after repair. What it does:

• Covers and ventilates the pan opening to help direct airflow and prevent debris entry
• Replaces a cracked, warped, or missing grille to restore fit and finish
• Helps eliminate rattling or rubbing caused by a damaged trim piece
• Matches OEM fit so it installs cleanly with the original mounting points

• Install requires removal of the surrounding trim or access panel; follow your appliance manual
• Handle carefully to avoid scratching the finish; use non-marring tools as needed
• Disconnect power to the appliance before working in the service area
• Replace damaged clips or screws with OEM fasteners for secure fit