Psa9249sf5ss Parts

Damaged door trim or RF choke exposed? This microwave choke cover snaps over the inner door edge to conceal the RF assembly and restore proper shielding.

This is a small self-tapping screw used to secure the control panel or other mounting components on a range or cooktop. It fastens internal brackets and panels in place to keep them stable during operation. Replace this screw if it is stripped, missing, or broken, which can cause loose or rattling panels.

Fix a blank or non-responsive display with this microwave VFD module and harness assembly. Restores control panel function when the display fails.

This control knob restores safe, easy operation of a stove or range control. It replaces a cracked, melted, or missing knob so you can adjust burners or oven settings with a secure grip and clear feel. What it does:

• Fits onto the appliance control shaft to select burner or oven settings
• Replaces damaged, loose, stripped, melted, or missing knobs
• Provides a firm, tactile grip for precise control
• Helps prevent accidental changes by seating securely on the shaft

• Disconnect power (and gas, if applicable) before servicing the appliance
• Remove the old knob by pulling it straight off the control shaft
• Align the knob with the control shaft splines and push firmly until fully seated
• If the knob does not install easily, verify shaft alignment and do not force.

This replacement control knob lets you select cooktop or oven heat settings with a secure, easy-to-turn grip. Restores a damaged, worn or missing knob so temperature and function selections operate normally. What it does:

• Fits onto the appliance control shaft to set burner or oven temperature and modes
• Replaces cracked, stripped or missing knobs that are hard to turn or won't stay set
• Provides a clear tactile stop and position for accurate control selection
• Helps eliminate slipping or loose rotation caused by worn knobs

• One replacement control knob

• Push-on installation: align splines with the control shaft and press firmly until seated
• Turn power off at the appliance or breaker before accessing internal components
• Do not force onto the shaft; if it does not fit, verify shaft type and knob orientation
• If the original knob is damaged at the shaft or insert, the switch may also require replacement

Grease filter traps cooking vapors and prevents buildup in your microwave. Replace when discolored or clogged to maintain ventilation. Verify fit with your model number.

Idle bracket for microwave and microwave/hood combo units. Secures internal components in proper position. Replace if bracket is bent, broken, or missing.

White outer cover that snaps over your microwave door handle. Replaces cracked, broken, or worn covers to restore a clean appearance. Includes front and rear pieces.

This is a single wiring harness used in a range or oven to carry electrical signals and power between internal components. It connects controls, sensors, or other electrical parts to ensure proper communication and operation. Replace this harness if you find damaged, burned, or corroded wires that are causing intermittent operation or error codes.

Plain washer for built-in microwaves and wall ovens. Replaces worn, missing, or damaged washers during repairs or maintenance. Essential hardware.

Microwave not heating food? The high voltage transformer powers the magnetron. Common failure part when microwave runs but won't heat properly.

This is the outer door panel assembly that forms the visible front surface of the oven door. It provides the exterior finish and structural support for the door while housing the handle mounting points. Replace this panel if it is dented, scratched, warped, or if the finish has deteriorated.

A direct-replacement supporter housing that secures and aligns internal components for stable operation. Restores proper positioning inside the appliance so parts sit correctly and function as intended. What it does

• Provides a secure mounting point and structural support for internal components.
• Keeps parts properly aligned to prevent binding, rubbing, or premature wear.
• Helps reduce movement that can lead to rattling or vibration-related noise.
• Maintains correct clearances so associated parts operate smoothly.

• Disconnect power (and water if applicable) before starting any repair.
• Basic hand tools required; handle plastic housings gently to avoid cracking.
• Verify proper orientation and secure fasteners snugly—do not overtighten.