Psd2450gr Parts

Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:

• Pushes or guides harvested cubes out of the ice mold into the bin during the ice maker's harvest cycle.
• Prevents cubes from sticking in the mold; a damaged stripper can cause incomplete ejection or leftover ice in the mold.
• Works with the ice maker's ejector mechanism to maintain consistent cube release and storage.
• A faulty or broken stripper may lead to noisy operation, partial fills, or visible ice build-up in the mold.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Remove the ice maker or access panel per the manufacturer's instructions to reach the stripper; keep small parts and screws organized.
• Inspect the ice mold and surrounding components for damage or ice build-up; clear ice before installing the new stripper.
• After installation, restore power and run a test harvest cycle to ensure proper cube ejection.

Refrigerator not cooling or humming without starting? The compressor pumps refrigerant to cool your fridge. Requires EPA certification for install.

Screw: 8-16 x 3/8 inch.

Replacement mounting screw secures panels, brackets, and trim to the appliance frame. Needed when original screw is stripped, missing, or damaged.

Mounting screw secures panels, brackets, and trim on refrigerators and washers. Replace when fasteners are missing, loose, stripped, or damaged.

Secures water supply hoses to fittings, preventing leaks in ice makers and refrigerators. Replace when rusted, bent, or losing grip. Verify fit.

This defrost heater clip secures the refrigerator's defrost heater to the evaporator assembly, keeping the heater in proper position for reliable defrost cycles and helping prevent ice buildup that impairs cooling performance. What it does:

• Secures the defrost heater to the evaporator so the heater maintains proper contact and alignment.
• Helps ensure the heater can melt frost and ice during automatic defrost cycles.
• Small replacement part that restores proper heater placement without replacing the entire assembly.

• Disconnect power to the appliance before accessing the evaporator or heater to avoid shock or injury.
• Replacement typically requires removing interior panels or an evaporator cover; handle evaporator fins carefully—they are sharp.
• Verify the heater and wiring are undamaged and positioned correctly when installing the clip.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

Replacement fastening screw for securing trim, panels, and brackets inside appliances. Use when original screw is missing, stripped, or damaged.

Fix excessive buzzing or rattling noise from your refrigerator's fan area. This rubber grommet cushions the fan motor mount to reduce vibration and noise.

Ice maker sagging or misaligned? This mounting bracket secures the ice maker assembly in place. Twist-fit installation—no adhesive needed.

Refrigerator not cooling or freezing? This compressor powers your cooling system. Professional installation recommended due to sealed system work.

This is a replacement pin wheel that secures and guides a mating linkage or small shaft in the appliance, restoring proper alignment and smooth movement. A direct-fit replacement when the original wheel is cracked, worn, or missing. What it does

• Holds and stabilizes a small rotating shaft or linkage to maintain proper component alignment
• Allows smooth transfer of motion between mating parts to prevent skipping or binding
• Worn or broken pin wheel can cause noise, intermittent movement, or improper function of the associated mechanism
• Small, inexpensive part that prevents further wear to adjoining components when replaced promptly

• One pin wheel

• Disconnect power to the appliance before starting any repair
• Access and removal often require removing a panel or nearby components; keep fasteners organized
• Inspect the mating shaft/clip and replace any damaged hardware for reliable operation
• Tighten and test moving parts by hand before restoring power; follow OEM service manual steps

This is a small roller wheel designed to support and allow smooth movement of components inside a refrigerator cabinet. It typically mounts on a bracket to help drawers, shelves, or other sliding parts glide easily. Replace this roller if a drawer or shelf is difficult to slide, makes scraping noises, or the wheel is cracked, flat-spotted, or no longer turns freely.

This genuine replacement screw secures appliance panels and trim so covers, consoles, and components stay firmly in place for safe, quiet operation. It replaces worn or missing fasteners to restore proper fit and reduce vibration and rattling. What it does:

• Secures control panels, trim pieces, or access panels to the appliance frame
• Keeps panels aligned to prevent gaps and light leaks
• Reduces vibration-related noise from loose panels or components
• Helps maintain safe operation by keeping covers and guards properly attached

• The replacement screw shown/listed

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start the screw by hand to ensure proper thread engagement, then tighten securely but do not overtighten

Replacement mounting screw for securing freezer panels, brackets, and components. Restores proper fastening where original screw is missing, stripped, or damaged.