Psf26ngwc Parts

This door gasket seals the refrigerator compartment to help maintain proper temperature and energy efficiency. It replaces a worn or damaged seal so cold air stays inside and warm, humid air stays out. What it does:

• Creates an airtight seal around the refrigerator door to reduce temperature fluctuations
• Helps prevent frost build-up and condensation by keeping warm air from entering
• Supports consistent cooling performance and helps reduce energy use
• Commonly replaced when the seal is cracked, torn, flattened, or no longer closes tightly

• Designed for direct replacement; fit by comparing part to the existing gasket before installation
• Clean the door flange and remove old gasket adhesive/residue for best seal
• Work slowly around corners to seat the gasket evenly; heat (hair dryer) may help soften stiffer gaskets for fitting
• Disconnect power if required by your model before performing any repairs and follow all safety instructions in your appliance manual

This adhesive-backed foam sealing strip provides a simple replacement to seal small gaps and cushion contact points on appliance doors and panels, helping reduce drafts, moisture intrusion, and rattling. What it does:

• Seals small gaps around doors, panels or assemblies to help limit air and moisture transfer and reduce condensation
• Cushions surfaces to minimize vibration and rattling noises
• Helps improve temperature retention by closing unintended openings
• Commonly replaced when foam is torn, compressed, detached, or causing drafts

• Verify the mounting surface is clean, dry and free of grease or old adhesive before applying
• Measure and trim the strip to fit; peel back adhesive liner and press firmly along the full length
• Avoid stretching the foam during installation for best seal and adhesion
• If adhesion is poor, remove residue and consider using a manufacturer-approved adhesive

This wire actuator engages the refrigerator dispenser paddle to activate water or ice dispensing. It restores reliable mechanical actuation for responsive dispenser operation without replacing the entire dispenser assembly. What it does:

• Translates paddle movement into the dispenser switch action so water or ice starts when the paddle is pressed
• Helps correct a dispenser that doesn't activate when the paddle is pushed
• Replaces a bent, broken or worn actuator wire that can cause inconsistent dispensing
• Works with the dispenser lever and switch assembly to restore proper alignment and motion

• Includes: 1 wire actuator for dispenser

• Disconnect power (unplug or shut off breaker) and turn off the water supply before starting
• Remove dispenser trim/paddle to access and replace the actuator; avoid forcing plastic clips
• Verify alignment with the dispenser switch and paddle during reassembly to prevent binding

This short freezer basket wire provides a sturdy support frame for the freezer compartment, helping organize frozen food and improving access. It replaces a damaged or missing basket wire to restore proper storage functionality. What it does:

• Supports and contains frozen items on a freezer shelf or drawer
• Restores proper fit and alignment for a short/freezer basket assembly
• Helps prevent items from shifting or falling through shelf openings
• Used when wire is bent, broken, or missing and basket stability is compromised

• One short freezer basket wire

• Remove food and unplug or power off the appliance before starting work
• Typically secures to existing shelf or drawer mounts—inspect mounts for damage before reinstalling
• Handle wire edges carefully to avoid cuts; wear gloves if needed

This control board harness connects a refrigerator's control board to dispenser, sensor, and power circuits, restoring reliable signal and power routing for proper operation. Designed as a direct replacement for a single harness assembly. What it does:

• Routes power and signal lines between the main control board and fridge subsystems.
• Restores functionality when damaged wires or broken connectors cause intermittent or no response.
• Can resolve symptoms like unresponsive dispenser/controls, nonworking lights, or sporadic electronic behavior.
• Maintains correct wire routing and connector alignment to prevent shorts and communication errors.

• Disconnect power to the appliance before servicing to avoid shock or component damage.
• Handle connector ends gently and seat fully; do not bend pins.
• Route harness away from sharp edges, moving parts, and heat sources; secure with existing clips or ties.

This wiring harness connects and supplies power to the dispenser motor so the dispenser operates reliably. It replaces a worn or damaged dispenser motor harness to restore electrical continuity and dependable dispenser function. What it does:

• Carries voltage and signals between the control and the dispenser motor
• Restores power when a broken or frayed harness prevents the motor from running
• Helps stop intermittent dispenser operation caused by loose or damaged wiring
• Provides proper connector fit to maintain a secure electrical connection

• Disconnect power to the appliance before inspecting or replacing the harness
• Handle connectors gently and verify correct orientation before mating
• Route harness following original wire paths and secure with existing clips to avoid pinching
• If corrosion or other damaged components are present, inspect surrounding parts and replace as needed