Rbf-G99 Parts

This small torsion spring powers the refrigerator's center door mullion (flipper), helping it flip and seal between the doors. Replacing a weak or broken spring restores smooth door action and helps prevent air leaks and condensation at the center joint.

• Provides return tension for the center mullion/flipper between the fresh food doors
• Helps the flipper align and seal properly for a tight door closure
• Supports smooth opening/closing of the door edge
• Symptoms may include the flipper not flipping back, door not closing flush, clicking/loose mullion, or moisture forming at the center seam

• Unplug the refrigerator before servicing
• Note the spring's orientation/leg position before removal; take reference photos
• Control spring tension and use needle-nose pliers with eye protection
• After install, verify the flipper moves freely and seals along the full height

This articulating mullion with built-in heater is the vertical door trim assembly that seals and insulates the gap between double doors, helping prevent frost and condensation. It restores proper door alignment and improves cold-air sealing. What it does:

• Provides a hinged vertical seal between freezer/refrigerator doors to help doors close smoothly and stay aligned
• Built-in heater reduces ice build-up and condensation along the door gap
• Helps maintain proper cold-air containment for consistent interior temperature
• Commonly replaces parts causing visible frost, moisture between doors, or binding/uneven door closure

• One articulating mullion assembly with heater

• Always disconnect power to the appliance before beginning repair
• Handle trim and heater wiring gently; ensure electrical connectors are fully seated and routed clear of moving parts
• After installation, restore power and verify doors close evenly and heater operates (check for heat at mullion after a short run)

This mullion bottom axle is the lower pivot that secures and lets the refrigerator mullion (vertical door trim) pivot properly, restoring correct door alignment and smooth opening/closing. Designed to replace a worn or broken lower mullion axle. What it does:

• Provides the lower pivot point for the refrigerator mullion/trim so doors stay aligned.
• Replaces a broken, bent, or worn axle that causes the mullion to wobble or not seat.
• Helps stop binding, uneven gaps, or rubbing between doors caused by mullion instability.
• Works with the mullion assembly to maintain proper door sealing and operation.

• One mullion bottom axle

• Disconnect power and remove any trim or mullion cover per manufacturer instructions before replacing.
• Handle trim pieces carefully to avoid scratching or damaging door finishes.
• Use proper fasteners and torque as specified by manufacturer; do not overtighten.

This condenser fan motor powers the refrigerator condenser fan to help move air across the condenser coils for proper cooling and efficient compressor operation. It replaces a failed fan motor so the condenser fan can run normally. What it does:

• Spins the condenser fan blade to pull or push air across condenser coils for heat dissipation.
• Restores proper airflow when the fan motor has seized, hums, or won't start.
• Helps reduce compressor cycling caused by poor condenser airflow.
• Works with the existing fan blade and mounting hardware when the motor is the only failed component.

• Disconnect power to the appliance before servicing to avoid electrical shock.
• Handle with care to avoid bending condenser fins or damaging wiring.

This mullion bracket secures the decorative trim (mullion) between oven or microwave sections, keeping the trim aligned and stable for a clean, finished appearance. It replaces a damaged or missing bracket to restore proper fit. What it does

• Anchors the mullion/trim to the appliance frame so panels stay flush and aligned
• Prevents trim from sagging, rattling, or separating from adjacent panels
• Helps maintain a consistent gap between doors or between oven/microwave sections
• Works as a structural mounting point for the mullion piece

• One mullion bracket

• Disconnect power to the appliance before starting any work
• Typical installation uses existing screws; support the trim while removing and reinstalling fasteners
• If access requires removing the oven or inner panels, handle panels carefully to avoid damage
• Tighten fasteners snugly but avoid over-torquing to prevent striping the bracket or screw holes

This mullion heater warms the vertical door mullion to reduce condensation and ice buildup between refrigerator doors, helping doors seal properly and reducing moisture-related odors. It's a direct-replacement heater for affected mullion assemblies. What it does

• Provides focused heat to the fridge/freezer mullion area to help prevent frost and ice buildup.
• Reduces condensation that can cause water drips or sticky door seals.
• Helps maintain a consistent door seal by preventing cold spots that let moisture accumulate.
• Common symptom: visible frost or ice between doors, water pooling, or poor door sealing.

• One mullion heater (heater strip/assembly) as described.

• Power should be disconnected before servicing electrical components.
• Typically installed behind the mullion or door trim; access may require removing trim panels.
• Handle wiring carefully and follow OEM wiring and routing; replace any damaged connectors or clips.

This display control panel is the refrigerator's electronic user interface that shows settings and accepts touch/button input so you can view and change temperatures and modes. Replaces a damaged or unresponsive front display. What it does:

• Provides the visual display for temperature, mode and status indicators
• Receives user input from touchpads/buttons to change settings
• Restores visible readout when the original panel is cracked, faded, or blank
• Helps fix issues where controls don't respond or display incorrect/missing information

• Disconnect power at the wall before starting to avoid shock.
• Handle the display lens and ribbon connector carefully to prevent damage.
• Reconnect all wiring harnesses and secure the panel before restoring power.