Rf365fxyq2 Parts

This bake element mounts at the bottom of the oven cavity and supplies the heat required for baking and roasting. Replace a failed element to restore proper preheat, even temperature, and reliable oven performance.

• Provides radiant heat for the lower oven during Bake mode
• Helps maintain the set temperature for consistent results
• Common failure symptoms: no heat in Bake, very slow preheat, uneven/undercooked food, or visible blisters/cracks/breaks in the element
• A shorted element may trip a breaker when Bake is started

• Disconnect power at the breaker or unplug the range before servicing (high-voltage hazard)
• Remove oven racks; take out element mounting screws and carefully pull the element forward to access terminals
• Note/photograph wire positions and transfer wires one at a time; ensure terminals are tight
• Reinstall mounting hardware, verify the element is centered and not touching the cavity, restore power, and test Bake

This small spring clip secures a heating element to its mounting bracket in a range or wall oven, keeping the element properly positioned for safe, consistent heating. Replaces a worn or missing retainer to stop the element from shifting or sagging. What it does:

• Retains the heating element against its mounting point or bracket
• Helps prevent element sagging, shifting, or rattling during use
• Maintains proper alignment and spacing for reliable performance

• 1 metal spring clip

• Disconnect power at the breaker and allow the appliance to cool completely
• Support the element while removing/installing the clip to avoid stressing terminals
• Match the original clip's orientation and location before reassembly
• Do not bend or overtension the heating element; replace any damaged hardware or wiring as needed

Color: Black. Instruction sheet included.

Color: Almond

This replacement screw secures appliance panels, brackets, and internal components so your unit stays assembled, aligned, and quiet. Use it to replace missing, stripped, or corroded hardware and restore a reliable factory-fastened connection.

• Fastens panels, brackets, or trim to the cabinet/frame
• Helps maintain proper alignment of doors, controls, or covers
• Replaces hardware that's missing, rusted, or with a stripped head
• Can help reduce vibration or rattling from loose fasteners

• Disconnect power and shut off gas/water supplies before service
• Match thread and length to the original; transfer any washers if present
• Start threads by hand to avoid cross-threading, then tighten with the correct driver
• Do not overtighten; snug until secure to prevent damage to plastic or sheet metal

Color: White. Size: 2 oz. can. Porcelain touch-up paint.

The Range Control Knob is an OEM replacement part for Whirlpool electric ranges. It fits over the infinite switch to control the heat levels of the surface elements. This knob allows precise adjustment of temperature settings, enabling users to easily select the appropriate heat levels for cooking.

Color: Black

Over time, the control knob can become damaged or worn out due to regular use. Issues like a loose or cracked knob, difficulty in turning it, or the knob not staying securely in place could indicate the need for replacement.

Symptoms of a faulty Range Control Knob include:

• Difficulty turning the knob or selecting heat levels
• The knob feels loose or wobbly
• The knob is cracked or visibly damaged

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This door stop clip mounts at the oven door hinge area to limit how far the door opens. Replacing a bent or missing clip restores the correct stop point and helps protect the hinge from overextension.

• Limits the oven door opening angle to a designed stop
• Helps prevent overextension that can strain or damage the hinge mechanism
• Common symptoms include the door dropping open too far, loose-feeling travel, or difficulty reinstalling the door
• Visual clues: bent, cracked, or missing clip at the hinge area

• Disconnect power or shut off gas; allow the appliance to cool completely
• Support the door; removal may be required to access the hinge area
• Install the clip in the same orientation/location as the original; replace on both hinges if your model uses two
• Verify smooth movement and that the door stops at the normal open position before use

Cyntec temperature sensor that monitors internal temperatures and sends readings to the appliance control. Replacing a faulty sensor helps restore accurate temperature readings so the appliance can regulate cycles and cooling properly. What it does:

• Measures temperature and sends signals to the control board to help manage operating cycles.
• A failing sensor can cause incorrect temperature readings, frequent on/off cycling, or temperature fluctuations.
• Contribute to cooling problems, defrost issues, or inconsistent freezer/refrigerator performance when defective.

• Disconnect power to the appliance before servicing to avoid electrical shock.
• Handle the sensor and wiring gently; avoid bending or damaging the probe or connector.
• Replace like-for-like and reconnect the wiring securely. If symptoms persist, run diagnostics.

Color: Black. For biscuit use WP8522567. For white use WP8522565.

Qty 4 needed to complete full insulation

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

This anti-tip bracket kit is an OEM replacement part for Whirlpool ranges. This bracket is typically installed at the back of the range and is secured to the wall or floor to prevent the range from tipping forward when heavy items, such as pots or pans, are placed on the open oven door.

The anti-tip bracket should be installed during the initial installation of the range and checked regularly to ensure that it is securely attached. If the bracket becomes loose or damaged in any way, it should be replaced immediately to ensure the safety of the range and anyone using it.

This kit includes:

• Anti-tip bracket
• Mounting screws (2)
• Anchors (2)
• Washer (1)

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Color: White.

This is a metal bracket only, for receptacle kit, which includes this bracket, order 330031.

Replacement front door assembly that restores proper door closure and exterior appearance on compatible Whirlpool appliances. Use this assembly when the original front door is cracked, dented, or no longer secures or aligns properly. What it does:

• Replaces a damaged or warped front door to restore proper fit and appearance.
• Helps resolve doors that won't latch, sit flush, or rub against the cabinet.
• Aligns with original mounting points so the latch and hinges operate correctly.
• Matches the original exterior finish for a consistent look after repair.

• Disconnect power to the appliance before beginning any repair.
• Support the door during removal and installation to prevent drops or damage.
• Handle any glass or trim carefully to avoid breakage and injury.
• Follow the OEM service manual or manufacturer instructions for proper alignment and fastening.