Scb1000mbb01 Parts

The Latch/Switch Holder (Left Side) is an OEM component specifically designed for GE microwaves. It is responsible for securely mounting the latch and door switch components on the left side of the microwave door. 

Symptoms of a bad latch/switch holder include:

• Loose, unstable, or improperly functioning door latch 
• Inoperative or faulty door switch preventing the microwave from operating  
• Physical damage or cracks in the holder plastic

Causes can include normal wear over time exposing internal wires, moisture damage compromising electronics or impact damage weakening the holder structure.

This GE replacement is compatible with Hotpoint, RCA, and Kenmore models.

This circulation motor powers the circulating fan to move air inside the appliance, helping maintain even temperatures and support proper cooling or heating performance. It replaces a worn or failed motor to restore airflow. What it does:

• Spins the circulating fan or blower to move air through the appliance compartment
• Helps maintain consistent internal temperature and airflow for efficient operation
• Can address symptoms such as weak or no airflow, uneven cooling/heating, or unusual motor noise
• Works as the rotating drive component that transfers power to the fan assembly

• One circulation motor as shown

• Disconnect power before attempting any service to avoid electrical shock
• Verify orientation and mounting before removal; note wiring positions for reinstallation
• Use proper tools and follow manufacturer instructions; replace any worn grommets or fasteners as needed

This heater holder is the mounting bracket that secures the oven heating element in place so the element stays aligned for reliable heating and safe operation. It helps prevent movement that can cause uneven cooking or damage. What it does:

• Holds and stabilizes the oven/heater element in the cavity so it stays properly positioned
• Keeps the element from contacting other components, reducing the risk of shorts or damage
• Helps maintain even heat distribution by preventing element sagging or misalignment
• Fits where the element mounts and supports normal operation of the heating circuit

• One heater holder/mounting bracket

• Turn power to the appliance off at the breaker before servicing to avoid shock
• Inspect the element and surrounding insulation for damage when replacing the holder
• Typically secures with screws or clips—retain hardware and note orientation for reassembly

This mounting bracket provides a secure support point for appliance components, restoring proper alignment and stability. Use it to replace a bent, broken, or missing bracket to stop rattling and prevent parts from shifting. What it does:

• Secures panels, assemblies, or internal components in their correct position
• Restores stability to reduce vibration, noise, and misalignment issues
• Replaces damaged or corroded brackets that allow parts to sag or move
• Matches OEM fit and mounting points for reliable reinstallation

• Install with the appliance unplugged or power/gas disconnected for safety
• Keep original fasteners when possible; replace any stripped or damaged screws
• Hand-start fasteners, then tighten to secure without over-torquing

This shaft ring is a small retaining clip that secures a rotating shaft in place, helping keep connected components aligned and moving smoothly. It's a simple replacement that restores proper shaft retention and reduces wobble. What it does:

• Clips into a shaft groove to hold components on the shaft
• Prevents axial movement and keeps parts from sliding out of position
• Helps reduce noisy or unstable operation caused by loose shaft components
• Commonly used where a compact, reliable retention method is required

• One shaft ring

• Inspect the shaft and groove for wear or debris before installing; clean as needed
• Use appropriate snap-ring pliers or a safe, non-marring tool to install/remove the ring
• Ensure the ring fully seats in the shaft groove and the retained part is secure before reassembly
• Disconnect power and follow appliance safety procedures before servicing

This outer door trim / door frame replaces damaged or cracked refrigerator door trim to restore appearance and proper fit. It provides a finished edge around the door and helps keep the door liner secured for reliable operation. What it does:

• Replaces a cracked, bent, or cosmetically damaged outer door trim piece
• Secures and aligns the door liner and outer shell for correct door fit
• Helps prevent rubbing, rattling, and gaps that can contribute to cold-air loss
• Restores the door's finished look and proper edge sealing

• Disconnect power to the appliance before beginning any repair
• Remove door and handle(s) per manufacturer instructions to access trim fasteners
• Keep track of screws and clips; transfer any door gasket or insulation if required
• Test door alignment and seal after installation; do not overtighten fasteners