Sears Elite Side Side Parts

This refrigerator water tank holds a reserve of water inside the fresh food section so the dispenser delivers a steady, chilled flow. Replace the reservoir if it's cracked, leaking, or internally restricted.

• Stores and chills dispenser water inside the refrigerator
• Helps maintain consistent dispenser flow and pressure
• Damage can cause leaks under drawers or inside the fresh food compartment
• Kinks or blockages can reduce flow or stop water dispensing

• Unplug the refrigerator and shut off the household water supply; dispense water to relieve line pressure.
• Access the tank behind the crisper/deli area; note tubing routing and connection points before removal.
• For push-to-connect fittings, depress the collar to release lines; cut tubing square and fully seat when reconnecting, then perform a gentle tug test.
• Restore water and power, check all connections for leaks, and purge air by dispensing water.

This door stopper limits and cushions the appliance door's travel to prevent overextension and damage to hinges or surrounding surfaces. Replacing a worn or broken stopper restores smooth, controlled door movement and consistent closing alignment.

• Limits door opening angle and provides a positive stop to prevent overextension
• Helps protect hinges and adjacent panels from impact or scuffing
• Promotes smoother opening/closing and more consistent door alignment
• Symptoms of a failed stopper can include over-swing, scraping/rubbing, clicking noises, or a loose "stop" feel

• Disconnect power to the appliance before servicing
• Open the door to access the stopper; support the door if necessary
• Remove the fastener/retainer, note the old stopper's orientation, and install the new stopper using existing hardware
• Slowly open and close the door to verify the stop action and clearances after installation

Restore reliable heat with this replacement heating element. A worn or damaged element can cause long heat-up times, uneven temperatures, or no heat at all. Swapping it out helps return consistent, dependable heating performance.

• Converts electrical energy to heat when energized
• Common symptoms: no heat, slow to heat, or uneven/inconsistent temperatures
• Visual clues: cracks, breaks, burn spots, or terminals damaged/corroded
• Helps resolve heat-related error codes after proper diagnosis

• Disconnect power at the breaker before servicing; verify no voltage present
• Note wire positions and terminal orientation before removal
• Handle carefully; avoid stressing terminals and element sheath
• Inspect wiring and connectors; replace any heat-damaged spade terminals before reassembly

The Guide Assembly Rail (RH) is an OEM part for LG refrigerators. This Right-hand rail is responsible for guiding the movement of drawers or shelves within the refrigerator, ensuring smooth and secure sliding. It helps maintain proper alignment and stability of the drawers, making it easier to access stored food items.

Causes of a bad guide rail can include wear and tear over time, damage due to heavy loads or excessive force when opening and closing the drawers, or misalignment from improper installation. A faulty rail can affect the performance of the drawer, leading to difficulties in accessing the refrigerator’s contents.

Symptoms of a bad guide rail include:

• Drawers not sliding in and out smoothly
• Misaligned or wobbly drawers
• Difficulty opening or closing drawers completely

This OEM LG part is also compatible with Sears/Kenmore.

This button lever is the small plastic actuator behind a push button that engages the internal latch or switch. Replace it to restore clean, reliable operation when the button sticks, feels loose, or no longer triggers the function.

• Links the external push button to an internal latch or microswitch so the feature operates
• Transfers motion smoothly and helps the button return after pressing
• Common failure points include cracked pivots, broken tabs, or worn contact surfaces
• Symptoms: button sticks, feels mushy or loose, requires extra force, or fails to activate

• Unplug the appliance or disconnect power before servicing
• Use your model's exploded view to access the button area and note lever orientation
• Release retaining tabs carefully; transfer any springs or clips from the old lever if reused
• Test button action before final reassembly

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

This electric surface burner replaces a worn or broken cooktop heating element to restore even heating for pots and pans. It's a direct-replacement heating element commonly used on many Frigidaire electric ranges and cooktops. What it does:

• Heats cookware by converting electrical energy into heat for stovetop cooking
• Replaces cracked, unresponsive, or unevenly heating elements
• Helps stop sparks, intermittent heating, or a burner that won't warm
• Works with compatible receptacles and cooktop wiring to complete the circuit

• One electric surface burner element

• Disconnect power to the range at the breaker or unplug before servicing
• Remove the cooktop grate and any retaining clips to lift out the old element; reinstall in reverse order
• Inspect terminal connections and receptacle for damage; replace receptacle if corroded or loose

This refrigerator Drawer Tray Assembly forms the shelf/frame that supports a storage drawer. Replacing a cracked or broken tray restores smooth drawer movement, proper support for food items, and organization inside the compartment.

• Supports and guides the storage drawer within the compartment
• Provides a stable, level surface for everyday use
• Replace if the tray is cracked, warped, or has broken tabs
• Common symptoms: drawer binds, drops, misaligns, or won't slide/close smoothly

• Disconnect power before servicing
• Remove the drawer and any items/glass from the area to prevent damage
• Align tabs/rails, seat the tray evenly, and avoid forcing parts together
• Transfer any reusable hardware from the original assembly if required

This supporter cover is a TV rear trim piece that protects and conceals internal components while restoring the set's appearance. It provides a finished look and covers the TV's support area for safe handling and cosmetic repair. What it does

• Covers and protects the TV's rear support area and nearby components from dust and incidental contact
• Restores the TV's exterior finish after damage or missing trim pieces
• Helps maintain correct spacing for the support/stand attachment area
• Common symptom: cracked, warped, missing, or loose rear trim exposing internal parts

• One supporter cover

• Unplug the TV and place it face down on a soft, non-abrasive surface before starting
• Installation may require removing screws or disengaging plastic clips; keep hardware organized
• Handle carefully to avoid scratching the display or bending mounting tabs
• Refer to the TV's service manual for disassembly instructions and torque/spec guidance

The Infinite Switch is an OEM component specifically designed for Frigidaire ranges. It controls the burners, allowing users to easily adjust heat levels and select different cooking zones. 

Causes of a bad infinite switch can include wear and tear over time, exposure to moisture or impacts from cookware, or underlying issues with the control board or wiring.

Symptoms of a bad infinite switch include:

• Burners failing to ignite or heat up when selected  
• Inability to change burner heat levels
• Flickering or non-responsive control panel lights
• Cooktop controls becoming unresponsive

Replacing the switch with this OEM Frigidaire part can help restore full functionality. It is compatible with freestanding and slide-in electric cooktop models. This replacement switch is also compatible with ranges sold under the Whirlpool, Roper, and Maytag brands.
 

This drawer tray assembly is the platform that supports a refrigerator storage drawer and guides it along the slides. Replacing a cracked or damaged tray restores smooth operation, proper alignment, and dependable support for your food items.

• Supports the drawer bin and its contents inside the compartment
• Interfaces with the slide/rail system for smooth in-and-out travel
• Helps maintain proper alignment so the drawer opens and closes fully
• Common symptoms: cracked or broken tray, broken tabs, wobbling drawer, sticking/binding, or difficulty closing

• Disconnect power and empty the drawer before service
• Remove the drawer per your model's instructions; release tabs or screws securing the tray
• Position the new tray, ensuring tabs/rollers seat correctly; reinstall any fasteners
• Reinstall the drawer and check for smooth travel before reloading

An in-line union for appliance tubing, this tube connector joins two sections of plastic line to create a secure, leak-resistant connection in the water circuit, ideal for restoring flow after a repair, trim, or reroute. What it does:

• Connects two lengths of compatible plastic tubing to form a continuous run
• Helps maintain proper water delivery through the appliance's water system
• Can address leaks, drips, or loose/failed connections at a splice point
• Useful when replacing, shortening, or rerouting tubing during service

• 1 tube connector

• Disconnect power and shut off the water supply before servicing
• Cut tubing square; ensure ends are clean, round, and free of gouges
• Insert tubing fully into the connector until seated, then perform a gentle pull test
• Restore water and inspect all joints for leaks; use the connector size that matches your tubing's outer diameter

This controller assembly is the main electronic control board that manages temperature, compressor, defrost, and user interface functions for compatible refrigerators. Replaces a failed control to restore normal electronic control and display operation. What it does:

• Controls compressor cycles, defrost timing, and temperature regulation for the refrigerator
• Interprets user inputs from the console and updates the display/status lights
• Can resolve symptoms like unresponsive controls, blank or erratic display, or incorrect temperature control
• Works with associated sensors and relays to coordinate cooling and defrost cycles

• One controller assembly as shown

• Disconnect all power before attempting repair to avoid shock or damage
• Handle the board by its edges and avoid static discharge; use a grounding strap if available

Door gasket assembly provides a secure, flexible seal around the appliance door to prevent leaks and maintain proper internal conditions. Replacing a torn or worn gasket restores sealing performance and reduces leaks, drafts, or temperature loss. What it does:

• Forms the primary seal around the door to keep water, air, and temperature inside the appliance.
• Stops visible leaks or pooling around the door opening.
• Helps prevent temperature fluctuations, frost buildup, or loss of cleaning/drying performance caused by a poor seal.
• Addresses visible damage symptoms such as cracks, tears, deformation, or persistent odors around the door edge.

• Always disconnect power (and water, if applicable) before starting any repair.
• Remove the old gasket carefully; inspect and clean the door channel and mounting surface before installing the new gasket.
• Ensure the replacement gasket is fully seated and any retaining clips or fasteners are secured per OEM instructions; test the door for proper fit and sealing.

This fresh room tray assembly replaces the crisper drawer tray that holds fruits and vegetables, restoring proper storage and organization in the refrigerator's fresh/produce compartment. Durable plastic construction supports produce and helps keep the fresh room tidy. What it does:

• Provides the flat tray surface for the fresh/produce compartment so drawers slide and store items securely
• Restores proper support if the original tray is cracked, warped, or broken
• Helps prevent items from falling into lower compartments and keeps produce organized
• Replaces worn or damaged trays that interfere with drawer movement or sealing

• Unplug or disconnect power to the refrigerator before servicing for safety
• Remove contents and the crisper drawer before installing the replacement tray
• Slide or snap the tray into the existing tracks/locator tabs; no special tools typically required
• If the tray does not seat smoothly, verify track alignment and avoid forcing parts to prevent damage

Replacement water-line tube that routes water inside the refrigerator to the ice maker or dispenser, helping restore proper water flow and reduce leaks. Designed to match factory routing so the line fits and seals correctly at the connections. What it does:

• Carries water from the cabinet valve to the ice maker or dispenser.
• Restores normal dispenser flow and ice production when the tube is cracked, pinched, or clogged.
• Helps stop visible leaks or pooling caused by damaged or misrouted tubing.
• Matches factory bends for correct routing and clearance behind panels.

• Disconnect power and shut off the water supply before starting any work.
• Remove shelves or panels as needed for access; watch for sharp edges.
• Check and replace any worn clamps or fittings; tighten connections and test for leaks with water on before reassembling.