Sge53u52uc/D5 Parts

This sump screw secures the dishwasher's sump or sump cover to the tub, keeping the assembly tight and leak-resistant. Replace a missing, stripped, or damaged screw to restore a proper seal and stable mounting.

• Fastens the sump or sump cover to the dishwasher tub
• Helps maintain a watertight seal to reduce leaks
• Keeps filter/sump components aligned and secure
• Replaces missing, stripped, or damaged hardware
• Helps address leaks or rattling around the sump area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack and filters to access the sump area
• Ensure mating surfaces and seals are clean and properly seated
• Tighten snugly by hand; do not overtighten to avoid stripping

The Screw is an OEM replacement part for Bosch dishwashers. Hundreds of screws hold the appliance panels and internal mechanisms securely in place. Consistent, protective enclosures ensure long-lasting performance.

Causes of a bad screw can include stripped threads from repeated tightening/loosening during repairs. Corrosion posing integrity risks may develop if water penetrates screw heads over time. 

Symptoms of a bad screw include: 

• Panels or racks that rattle or come loose during operation
• Gaps appear that allow residual moisture to seep within
• Internal components shifting position from the original assembly
• Loose wiring susceptible to abrasion posing electrical hazards

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This spray arm distributes wash water throughout the dishwasher and spins to reach all areas. Replace a cracked, warped, or clogged arm to restore strong spray coverage, quieter operation, and consistent cleaning performance.

• Rotates under water pressure to direct jets across dishes for even wash and rinse coverage
• Helps ensure detergent dissolves and food soils are flushed away
• Common failure signs: poor cleaning, arm not spinning, unusual noise from hitting items, visible cracks/warping, or clogged nozzles
• A damaged or obstructed arm can lead to weak spray and undissolved detergent

• Disconnect power before servicing
• Remove rack(s) as needed; release the arm from its hub by twisting or unlocking tabs (varies by model)
• Clear debris from the hub/nozzle area; seat the new arm and confirm it spins freely
• Run a test cycle to check for proper rotation and leaks

The Flow Meter Sensor is an OEM component specifically designed for Bosch dishwashers. It monitors water volume flowing into the unit during cycles to ensure sufficient levels for optimal cleaning performance. Precise detection prevents inefficient or ineffective washings.

Causes of a bad flow meter sensor can involve scale buildup obstructing readings or normal internal component wear reducing accuracy over time. Heat exposure risks also impact functionality warranting replacement. 

Symptoms of a bad flow meter sensor include:

• Incomplete or insufficient water fill during cycles  
• Soiled dishes remain even after normal duration wash/rinses
• Faulty water usage readings causing cycle malfunctions

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. Replace to restore full water volume sensing for thoroughly clean dishes on every cycle.
 

The Divertor Motor is an OEM part for Bosch dishwashers.  This part controls the direction of water flow within the unit. This motor directs the water to different spray arms based on the selected wash cycle, ensuring efficient cleaning by optimizing water usage and spray intensity. 

Causes of damage to the divertor motor can include regular wear and tear, exposure to water and detergent over time, and electrical issues such as wiring problems or faults in the control board.

Symptoms of a failing Divertor Motor include:

• Inadequate water distribution during cycles, which can lead to uneven cleaning results.
• The dishwasher making unusual noises, such as humming or grinding, which may indicate a struggle in the motor function.
• Certain wash zones receiving little to no water, affecting the appliance's overall performance.
• Error codes displayed on the dishwasher panel that relate to water circulation problems.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Flip Tine is an OEM part for Bosch dishwashers. It provides an anchor point for attaching dishes and other items securely inside the dishwasher. The tine's ability to flip enables versatile loading and optimal washing coverage.

Causes of a bad flip tine can include wear and tear that impacts its secure movement over time or damage such as cracks or breaks that occur accidentally.

Symptoms of a bad flip tine include: 

• Tine that no longer flips securely into place
• Loose or wobbly tine attachment points
• Difficulty loading items securely on the tine
• Reduced washing performance for items placed on the tine

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. Replace yours today to regain full functionality and washing effectiveness.

The Shower is an OEM component designed specifically for Bosch dishwashers. It provides superior coverage and washing performance through its unique rotating arm and nozzle design. Causes of a bad spray arm and shower head include mineral deposits restricting spray patterns, cracked or broken assembly parts, or worn nozzles that no longer fully rotate. 

Symptoms of a bad part include: 

• Soil or food debris that isn't fully removed from crevices or hard to reach areas
• An arm that doesn't rotate smoothly during the cycle or gets stuck
• Cracks or breaks in the plastic that cause leaking or restricted spray patterns

This Bosch part can also be used on Thermador and Gaggenau appliances.

This door cable links the door hinge to the tension spring to counterbalance your dishwasher door, helping it open smoothly and stay under control. Replace a worn or broken cable to restore proper door action.

• Connects the door hinge to the spring to counterbalance door weight
• Helps prevent the door from dropping open or slamming
• Common symptoms: door feels heavy, drops quickly, or won't stay in position
• Uneven or crooked door movement can indicate a failed cable on one side
• Visible fraying or a snapped cord near the spring/pulley area

• Disconnect power at the breaker and shut off water before servicing
• Support the door and carefully relieve spring tension before removing the cable
• Route the new cable exactly as the original over the pulley; attach to hinge and spring
• Inspect both sides, springs, and pulleys; replace any worn components for balanced operation

This fixing kit is the original installation hardware set used to secure specific components or panels on your appliance. Replacing worn or missing hardware restores a solid, rattle-free fit and proper alignment after installation or service.

• Provides the mounting fasteners/brackets needed to attach a panel or subassembly to the appliance
• Addresses loose or missing hardware that can cause vibration, rattling, or shifting
• Helps correct gaps or misalignment after installation or repair
• Matches original attachment points for a secure, model-correct fit

• Disconnect power before servicing; wear appropriate safety gear
• Compare new hardware to the originals and install in the same locations/orientation
• Tighten fasteners evenly; avoid overtightening into plastic or thin sheet metal
• Verify level, clearances, and smooth operation after securing components

This small replacement insert restores proper fit, finish and component alignment in compatible Bosch appliances. It helps secure panels or controls and keeps gaps closed for a clean, stable installation. What it does:

• Replaces a worn, damaged or missing insert used to align or secure adjacent trim and panels.
• Helps reduce rattling, looseness or misalignment caused by missing interior trim.
• Restores a finished appearance where the original insert is broken or missing.
• Works as a non-electrical, mechanical trim component—no wiring changes required.

• Disconnect power to the appliance before accessing internal panels or trim.
• Use basic hand tools to remove surrounding trim; keep fasteners for reassembly.
• Check fit and orientation before final tightening to avoid panel distortion.

This temperature sensor (NTC) monitors wash temperature and reports it to the control so the cycle heats and advances correctly. Replacing a faulty sensor can restore proper cleaning performance and normal cycle times. What it does:

• Measures water temperature and sends resistance changes (NTC) to the control
• Helps the control regulate heating and cycle progression
• Failure symptoms can include no/insufficient heat, extended cycles, or poor drying
• May trigger a temperature-sensor fault (e.g., E11 on some models)

• 1 temperature sensor

• Disconnect power and turn off water supply before servicing
• Access is typically at the sump/heat-pump area; remove the toe-kick/lower panel as needed
• Expect some residual water; place a towel or tray to catch drips
• Ensure the sensor seats fully and the seal is in good condition to prevent leaks

This fixing kit is a replacement set of mounting hardware used to secure appliance components or panels. It restores a tight, aligned fit when original fasteners are lost, stripped, or damaged. What it does:

• Secures panels or components to the appliance frame
• Replaces missing or worn hardware to restore proper fastening
• Helps correct looseness, rattling, or minor misalignment
• Supports proper fit after service or part replacement

• One fixing kit

• Disconnect power (and shut off water/gas if applicable) before servicing
• Match each fastener to the original location and orientation
• Hand-start threads to avoid cross-threading; tighten evenly without overtightening
• Refer to the model's service documentation for any specified sequence or torque

This seal creates a tight, leak-proof interface between mating components inside your appliance. Replacing a worn seal helps stop drips and protects nearby parts for reliable, leak-free operation.

• Forms a watertight barrier between connected parts
• Replaces cracked, flattened, or deformed sealing material that can leak
• Helps address puddling, dampness, or seepage around the unit
• Maintains proper performance and helps prevent water damage to surrounding components

• Disconnect power and shut off the water supply before servicing
• Access the sealed joint and note the original orientation and seating depth
• Clean mating surfaces; do not use sealants unless specified by the manufacturer
• Seat the new seal evenly; lightly lubricate with a water-safe lubricant and run a test cycle to check for leaks

This genuine water inlet routes household water into the appliance's fill system, helping ensure consistent water delivery and a secure, leak-resistant connection. Replacing a worn or damaged inlet restores proper filling performance and helps prevent leaks at the entry point. What it does:

• Connects the supply line to the unit and directs water into the fill system
• Helps maintain a watertight seal at the water entry connection
• Supports proper fill by working with the appliance's control and fill components
• Common symptoms: no or slow fill, dripping/leak at the inlet connection, visible cracks or mineral buildup on the fitting

• 1 water inlet

• Disconnect power and turn off the water supply before servicing
• Place a towel or pan to catch residual water when removing the old part
• Note the orientation; reinstall existing seals/clips in their original positions if applicable
• Tighten fittings snugly without overtightening; restore water and check for leaks before use

This repair set renews the hinge pivot components so the door opens smoothly and closes squarely. Replacing the worn hardware helps maintain proper alignment and a tight gasket seal for consistent performance. What it does:

• Replaces worn hinge pin/bushing hardware to restore door support
• Helps fix a door that sags, scrapes, or won't close flush
• Can reduce clicking, squeaking, or grinding at the hinge
• Helps the door seal make full contact to prevent warm air leaks

• 1 repair set

• Disconnect power; if applicable, turn off the water supply
• Remove items from the door; support the door and lift it off the hinge
• Install the new hinge hardware in the original orientation
• Reinstall and align the door; verify gasket seal and adjust leveling if needed

White tray handle that restores a secure grip and smooth operation to your appliance's tray. Direct-fit replacement that matches the original handle's mounting points for an easy, reliable swap-out. What it does:

• Provides a secure grip for pulling out and pushing in the appliance tray.
• Stabilizes the tray to help prevent tipping or accidental drops when loaded.
• Addresses symptoms like cracked, broken, loose, or missing handle that make the tray hard to open.
• Matches the original shape and mounting locations for proper fit and function.

• Disconnect power at the breaker or unplug the appliance before working near electrical components.
• Remove the tray or rack as needed to access mounting screws or clips; retain original hardware unless replacement hardware is specified.
• Align the handle with the mounting points and secure using the existing screws/clips; avoid over-tightening to prevent damage.