Sgv55m43eu/10 Parts

This factory mounting set secures an appliance component in its proper position. Replacing worn or missing hardware restores a tight, stable fit to help keep parts aligned and the unit operating smoothly and quietly. What it does:

• Fastens the specified component to its mounting points for a secure hold
• Restores a proper fit when original hardware is stripped, broken, or lost
• Helps reduce vibration, rattling, and shifting during operation
• Supports correct alignment to prevent premature wear and noise

• One mounting set

• Disconnect power and shut off water or gas before servicing
• Support the appliance/component while removing and reinstalling hardware
• Reinstall in original locations and tighten fasteners to manufacturer guidance; do not overtighten
• Verify alignment and a secure fit before returning the unit to service

This replacement screw secures appliance panels and internal brackets so components stay tight and aligned during everyday use. Replacing missing or stripped hardware restores a solid fit and helps minimize vibration and rattling.

• Fastens covers, panels, and brackets to their mounting points
• Helps maintain alignment of the attached component
• Reduces movement that can cause noise or wear
• Typical reasons to replace: missing screw, stripped head/threads, loose panel or bracket

• Disconnect power and, if applicable, shut off water before servicing
• Use the driver bit specified for your model; hand start threads to avoid cross-threading
• Tighten snugly without over-torquing to prevent stripping
• Replace screws one at a time to maintain alignment

This door cable links the door hinge to the tension spring to counterbalance your dishwasher door, helping it open smoothly and stay under control. Replace a worn or broken cable to restore proper door action.

• Connects the door hinge to the spring to counterbalance door weight
• Helps prevent the door from dropping open or slamming
• Common symptoms: door feels heavy, drops quickly, or won't stay in position
• Uneven or crooked door movement can indicate a failed cable on one side
• Visible fraying or a snapped cord near the spring/pulley area

• Disconnect power at the breaker and shut off water before servicing
• Support the door and carefully relieve spring tension before removing the cable
• Route the new cable exactly as the original over the pulley; attach to hinge and spring
• Inspect both sides, springs, and pulleys; replace any worn components for balanced operation

This fixing kit is the original installation hardware set used to secure specific components or panels on your appliance. Replacing worn or missing hardware restores a solid, rattle-free fit and proper alignment after installation or service.

• Provides the mounting fasteners/brackets needed to attach a panel or subassembly to the appliance
• Addresses loose or missing hardware that can cause vibration, rattling, or shifting
• Helps correct gaps or misalignment after installation or repair
• Matches original attachment points for a secure, model-correct fit

• Disconnect power before servicing; wear appropriate safety gear
• Compare new hardware to the originals and install in the same locations/orientation
• Tighten fasteners evenly; avoid overtightening into plastic or thin sheet metal
• Verify level, clearances, and smooth operation after securing components

This small replacement insert restores proper fit, finish and component alignment in compatible Bosch appliances. It helps secure panels or controls and keeps gaps closed for a clean, stable installation. What it does:

• Replaces a worn, damaged or missing insert used to align or secure adjacent trim and panels.
• Helps reduce rattling, looseness or misalignment caused by missing interior trim.
• Restores a finished appearance where the original insert is broken or missing.
• Works as a non-electrical, mechanical trim component—no wiring changes required.

• Disconnect power to the appliance before accessing internal panels or trim.
• Use basic hand tools to remove surrounding trim; keep fasteners for reassembly.
• Check fit and orientation before final tightening to avoid panel distortion.

This temperature sensor (NTC) monitors wash temperature and reports it to the control so the cycle heats and advances correctly. Replacing a faulty sensor can restore proper cleaning performance and normal cycle times. What it does:

• Measures water temperature and sends resistance changes (NTC) to the control
• Helps the control regulate heating and cycle progression
• Failure symptoms can include no/insufficient heat, extended cycles, or poor drying
• May trigger a temperature-sensor fault (e.g., E11 on some models)

• 1 temperature sensor

• Disconnect power and turn off water supply before servicing
• Access is typically at the sump/heat-pump area; remove the toe-kick/lower panel as needed
• Expect some residual water; place a towel or tray to catch drips
• Ensure the sensor seats fully and the seal is in good condition to prevent leaks

This fixing kit is a replacement set of mounting hardware used to secure appliance components or panels. It restores a tight, aligned fit when original fasteners are lost, stripped, or damaged. What it does:

• Secures panels or components to the appliance frame
• Replaces missing or worn hardware to restore proper fastening
• Helps correct looseness, rattling, or minor misalignment
• Supports proper fit after service or part replacement

• One fixing kit

• Disconnect power (and shut off water/gas if applicable) before servicing
• Match each fastener to the original location and orientation
• Hand-start threads to avoid cross-threading; tighten evenly without overtightening
• Refer to the model's service documentation for any specified sequence or torque

This genuine water inlet routes household water into the appliance's fill system, helping ensure consistent water delivery and a secure, leak-resistant connection. Replacing a worn or damaged inlet restores proper filling performance and helps prevent leaks at the entry point. What it does:

• Connects the supply line to the unit and directs water into the fill system
• Helps maintain a watertight seal at the water entry connection
• Supports proper fill by working with the appliance's control and fill components
• Common symptoms: no or slow fill, dripping/leak at the inlet connection, visible cracks or mineral buildup on the fitting

• 1 water inlet

• Disconnect power and turn off the water supply before servicing
• Place a towel or pan to catch residual water when removing the old part
• Note the orientation; reinstall existing seals/clips in their original positions if applicable
• Tighten fittings snugly without overtightening; restore water and check for leaks before use

This repair set renews the hinge pivot components so the door opens smoothly and closes squarely. Replacing the worn hardware helps maintain proper alignment and a tight gasket seal for consistent performance. What it does:

• Replaces worn hinge pin/bushing hardware to restore door support
• Helps fix a door that sags, scrapes, or won't close flush
• Can reduce clicking, squeaking, or grinding at the hinge
• Helps the door seal make full contact to prevent warm air leaks

• 1 repair set

• Disconnect power; if applicable, turn off the water supply
• Remove items from the door; support the door and lift it off the hinge
• Install the new hinge hardware in the original orientation
• Reinstall and align the door; verify gasket seal and adjust leveling if needed

Tall item spray head.
This Spray Head is an OEM part for Bosch Dishwashers. It plays a role in distributing water evenly during the dishwasher's washing cycles. Continuous exposure to hard water, debris, or mineral deposits can cause issues with this component.

What Causes a Bad Spray Head:
Hard water deposits, debris, or mineral buildup can clog or block the spray head, affecting its performance. Physical damage can also impair its functionality.

Symptoms of a Bad Spray Head:

• Inadequate cleaning of dishes
• Uneven water distribution
• Reduced water pressure during washing cycles

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.
 

Replacement silverware basket with integral handle in dark gray. Holds forks, knives and spoons in the lower dishwasher rack to keep utensils upright for better cleaning and easier loading, removal and transport. What it does:

• Holds and separates flatware to reduce nesting and promote water flow during wash cycles.
• Integrated handle makes it easy to lift the basket in and out of the rack for loading or unloading.
• Keeps small items from falling through the rack and reduces rattling during operation.
• Replace the basket if it is cracked, broken, or if utensils no longer stay securely in place.

• Installs in the lower dishwasher rack by sliding or snapping into existing rack slots; typically requires no tools.
• Make sure the basket sits level and the handle moves freely before running the dishwasher.
• Inspect for cracks or sharp edges and replace if damaged to avoid utensil loss or interference with spray action.
• Disconnect power first; this part itself does not require electrical work.

This genuine replacement bearing supports the washer drum for smooth, stable rotation and helps reduce noise and vibration caused by worn or damaged bearings. Restores proper drum alignment for quieter operation. What it does:

• Supports the inner drum so it spins smoothly and stays aligned
• Reduces grinding, rumbling, squeaking or knocking noises from the drum
• Helps prevent excessive drum wobble that can damage seals or the tub
• Used when worn bearings cause rough rotation, metal-on-metal noise, or visible drum play

• Disconnect power (and water if applicable) before starting any repair
• Replacing this bearing typically requires partial disassembly of the washer/drum assembly and specialty tools
• Inspect shaft/hub, seals, and surrounding components for wear and replace if damaged

This front leveling leg supports and adjusts the appliance at the front, helping it sit stable and truly level. Replace a damaged or missing leg to restore proper height, stability, and smooth door alignment during everyday use.

• Provides height adjustment at the front to level the appliance
• Helps prevent rocking, vibration, and rattling
• Maintains correct cabinet/door alignment for proper operation
• Replace if the foot is cracked, stripped, missing, or won't adjust
• Common signs: unit wobbles, sits unevenly, or is difficult to level

• Disconnect power; if applicable, shut off water or gas. Pull the appliance forward and remove the toe-kick/access panel for clearance.
• Protect the floor; tilt or raise the front slightly to reach the leg.
• Unscrew the damaged leg; thread the new leg in by hand to avoid cross-threading.
• Adjust height until level front-to-back and side-to-side; verify stability before returning to service.

This factory screw secures select Bosch/BSH appliance components. Use it to replace a missing or damaged fastener so panels, brackets, or trim stay tight and rattle-free during operation.

• Tightens and holds appliance parts such as panels, brackets, or trim in place
• Helps correct issues like loose or vibrating panels caused by a missing/stripped screw
• Maintains proper fitment after service or disassembly
• Torx T20 drive head helps resist cam-out during tightening

• Unplug power and shut off any water supply before servicing
• Use a T20 Torx driver; hand-start to avoid cross-threading
• Do not overtighten—snug to manufacturer torque guidance if available
• Replace any additional missing or damaged fasteners for even clamping

This O-ring is a circular sealing gasket that creates a watertight joint between mating parts. Replacing a flattened or cracked ring restores a tight seal and helps prevent leaks during operation.

• Provides a compressible seal between fittings, hoses, or housings
• Helps prevent drips and leaks at joints under normal system pressure
• Maintains proper flow by keeping connections sealed
• Typical failure signs: visible cracking/flattening, seepage at a joint, pooling water near the appliance

• Disconnect power and shut off the water supply before servicing
• Relieve any line pressure and place a towel to catch residual water
• Clean and inspect mating surfaces; replace any damaged components
• Lightly lubricate the O-ring with approved silicone lubricant, seat evenly without twisting, and test for leaks after reassembly

The Levelling Foot is an OEM replacement part designed specifically for Bosch dishwashers. It works to properly position and stabilize the appliance for balanced and smooth operation. Causes of a bad levelling leg/foot can include general wear and tear over time. 

Symptoms of a bad levelling foot include: 

• An unbalanced or unstable dishwasher during use
• Rocking or shifting of the unit on an uneven surface 

This genuine OEM Bosch part restores proper alignment and support of the dishwasher to ensure optimal performance and noise reduction. This Bosch part can also be used on Thermador and Gaggenau appliances.