She3ar72uc Parts

This control unit is the appliance's main electronic control board. It directs power and timing to components and interprets sensor and user inputs. Replacing a failed board helps restore reliable operation and responsive controls.

• Coordinates cycle timing and operating modes for the appliance
• Sends power to components based on program logic
• Interprets signals from sensors and switches; interfaces with the user controls/display
• Common failure signs: dead or unresponsive controls, won't start or complete cycles, intermittent operation, or recurring error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the PCB with ESD precautions; avoid touching circuitry and components
• Label/photograph wiring; transfer connectors one at a time to the new board
• Secure mounting and connections before restoring power and testing

This replacement screw secures panels, brackets, and internal parts in your appliance for a tight, rattle-free fit. Use it to replace lost, stripped, or corroded hardware and keep components properly fastened.

• Fastens components to the appliance frame or assemblies
• Replaces a missing, stripped, or rusted original screw
• Helps reduce rattling or vibration from loose hardware
• Restores proper alignment of panels or brackets

• Disconnect power and shut off water before servicing
• Refer to your model's parts diagram to locate and place
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening

The control unit is the appliance's main electronic control board. It manages cycle timing and directs power to key components, helping the machine start, run, and complete programs as designed.

• Governs program logic and timing for each cycle
• Distributes power to components such as pumps, valves, motors, and heaters
• Interfaces with sensors and the door latch to advance or pause operation
• Helps regulate heating and drying functions where applicable
• Common failure symptoms: won't start, won't advance or complete a cycle, stops mid-cycle, no fill or no drain, or erratic operation

• Disconnect power at the breaker (and shut off water supply if accessing a dishwasher) before servicing
• Access location varies by model; refer to your unit's tech sheet
• Use ESD protection; handle the board by edges and transfer connectors one at a time
• After installation, restore power and run any model-specific diagnostic/service test to verify operation

This metric M4 x 8 screw secures the toe-kick/lower access panel at the base of the appliance. Replace a missing or stripped fastener to keep the kickplate tight and aligned, helping prevent looseness and noise.

• Secures the toe-kick or lower access panel to the base/frame
• Restores proper fit when the original screw is lost or damaged
• Helps reduce panel rattles and vibration
• Maintains correct alignment and clearance at the bottom edge

• Disconnect power before servicing; also shut off the water supply
• Support the panel and align holes before threading the screw
• Start by hand to avoid cross-threading; tighten snugly—do not overtighten
• Verify size matches the original; replace matching hardware together if required by your model

This sump screw secures the dishwasher's sump or sump cover to the tub, keeping the assembly tight and leak-resistant. Replace a missing, stripped, or damaged screw to restore a proper seal and stable mounting.

• Fastens the sump or sump cover to the dishwasher tub
• Helps maintain a watertight seal to reduce leaks
• Keeps filter/sump components aligned and secure
• Replaces missing, stripped, or damaged hardware
• Helps address leaks or rattling around the sump area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack and filters to access the sump area
• Ensure mating surfaces and seals are clean and properly seated
• Tighten snugly by hand; do not overtighten to avoid stripping

The Water Inlet Fill Hose is an OEM part for Bosch dishwashers. This part is responsible for safely and efficiently connecting the dishwasher to your home's water supply, ensuring that water flows into the dishwasher at the correct pressure and volume for optimal cleaning performance. 

Over time, the Water Inlet Fill Hose can become susceptible to wear and tear, leaks and blockages.

Symptoms indicating the need for a new Water Inlet Fill Hose include:

• Water pooling around the dishwasher base, pointing to a potential leak in the hose.
• The dishwasher not filling with water properly, or filling very slowly, suggesting a blockage or damage to the hose.
• A visible inspection reveals cracks, bulges, or signs of corrosion on the hose connectors.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This factory fastener secures panels, brackets, or internal components in your appliance, helping keep assemblies tight and rattle-free. Replace missing or stripped screws to restore a secure fit and dependable operation.

• Fastens components to the appliance frame, chassis, or panel assemblies
• Helps maintain alignment and reduce vibration or rattling
• Replaces lost, rusted, or stripped screws during service
• Common signs it's needed: loose panel or handle, vibration noises, or parts that won't stay secured

• Disconnect power and shut off water or gas before servicing
• Match the screw's location and length to the original from your model
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver type/size specified for your model's screw head

This replacement spring restores proper tension to the linked mechanism so it moves smoothly and returns to its intended position. Replacing a worn or broken spring helps correct looseness, sticking, and misalignment in the affected assembly. What it does:

• Provides return force and tension for the associated latch, lever, or panel
• Helps the mechanism open/close smoothly and stay in position
• When weakened or broken, can cause poor latching, sluggish return, or a loose feel
• Reduces squeaks or rattling from an under-tensioned mechanism

• 1 spring

• Disconnect power to the appliance before servicing; shut off water or gas if applicable
• Note spring orientation and anchor points before removal; take reference photos
• Use needle-nose pliers to remove/attach the spring; mind pinch points and stored tension
• Refer to your model's parts diagram for routing and placement

This insulating part installs in the appliance to form a protective thermal barrier. It helps limit heat transfer to nearby areas and components for safer operation and more consistent performance.

• Creates a thermal barrier around the designated section of the appliance
• Helps maintain stable internal temperatures and operating efficiency
• Shields adjacent wiring, plastics, and trim from excessive heat exposure
• Signs of failure can include brittle/crumbling insulation, visible gaps/missing sections, or hot spots on nearby panels

• Disconnect power and allow the unit to cool completely before servicing; shut off gas/water if applicable
• Access the insulated area and note the original orientation/coverage before removal
• Reuse existing fasteners/retainers; seat the insulation without over-compressing it
• Handle material carefully; wear gloves and eye protection to avoid irritation and cuts

This button replaces a worn or missing pushbutton on the appliance's control panel. It restores a positive, reliable feel when selecting settings and ensures your press properly actuates the underlying switch.

• Serves as the fingertip interface on the control console
• Transfers your press to the user interface/microswitch behind the panel
• Helps restore proper selection and start/stop response
• Typical symptoms: cracked or missing cap, sticking button, loose fit, or presses that don't register

• Disconnect power before servicing
• Remove the console/control panel to access the old button
• Note orientation; release retaining tabs and install the new button fully seated
• Reassemble the panel and test all button functions

The Power Module Programmed is an OEM component specifically designed for advanced Bosch dishwashers. It serves as the intelligent control center, enabling customized cycles tailored for optimal washing results. The programmed power module analyzes load sizes and soil levels to self-adjust water, temperatures, and cycles accordingly.

Causes of failure can include defects in electronic programming from harsh chemicals or water exposure over time. Physical damage such as pins or connections becoming dislodged may also hinder function.

Symptoms include:

• Inability to run specialized cycles like Quick Wash or Glass Care  
• Defaulting to only standard cycles regardless of load type
• Fault codes or resetting of customized programming  
• Full non-responsiveness requiring replacement

Replacing with this genuine Bosch module restores smart cycle optimization. It regulates washing perfectly for dishes, pots, pans, and delicate glassware alike. Compatible with Miele, Thermador, and select Asko models.
 

The Hose Vent is an OEM part for Bosch dishwashers. It is responsible for venting excess heat, moisture, and odors generated during the washing process, ensuring a safe and suitable internal environment. The hose vent guides steam out of the appliance, preventing damage caused by pressure buildup. 

Symptoms of a bad hose vent include: 

• Visible damage or cracks along its length
• Kinks or depressions restricting airflow
• Disconnections from vent ports or dishwasher interior
• Excess moisture inside the dishwasher 

Causes of hose vent failure can be related to extended use over time, crushing/pinching from the installation environment, or buildup of debris affecting airflow.

This genuine Bosch replacement hose vent will restore proper moisture removal. It is compatible with some Siemens, Thermador, Gaggenau, and Kenmore models. Replace yours today for reliable venting performance.

This replacement screw secures appliance panels and internal brackets so components stay tight and aligned during everyday use. Replacing missing or stripped hardware restores a solid fit and helps minimize vibration and rattling.

• Fastens covers, panels, and brackets to their mounting points
• Helps maintain alignment of the attached component
• Reduces movement that can cause noise or wear
• Typical reasons to replace: missing screw, stripped head/threads, loose panel or bracket

• Disconnect power and, if applicable, shut off water before servicing
• Use the driver bit specified for your model; hand start threads to avoid cross-threading
• Tighten snugly without over-torquing to prevent stripping
• Replace screws one at a time to maintain alignment

Fine filter designed to trap food and debris in the dishwasher's wash system, helping prevent pump clogs and reduce redeposited soils on dishes. Direct replacement for the dishwasher's original fine-mesh filter. What it does:

• Captures food particles and fines from wash water to keep the pump and circulation system clear.
• Helps reduce food redeposit and maintain wash performance when functioning properly.
• Can prevent coarse debris from reaching the wash pump and drain components.
• Common signs a filter needs cleaning or replacement include visible food on dishes, recurring clogs, or poor wash results.

• Always disconnect power to the appliance and turn off the water supply before servicing.
• Remove the lower dish rack to access the filter area; handle the filter gently to avoid damage.
• Clean the filter seat and surrounding area before installing; ensure the filter is seated and secured per the owner's manual.

This factory screw secures appliance components per the original design, helping stop looseness and vibration. Replace a missing, stripped, or corroded fastener to restore a solid, rattle-free fit and protect nearby parts from damage.

• Secures panels, brackets, or internal components as specified by the manufacturer
• Helps maintain proper alignment and reduces vibration or rattling
• Replace if the head is stripped, threads are damaged, or the screw is missing
• Common signs include loose or misaligned panels/trim and hardware that won't stay tight

• Disconnect power and turn off water or gas supply as applicable before servicing
• Match length and thread to the original; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly without overtightening
• Retain any original washers, bushings, or clips used in the assembly

This is a Bosch dishwasher control board. The dishwasher's control board ensures that the various cycles and settings can be properly managed, such as the washing and draining cycles. If the user notices issues with dishes not coming out clean after a full cycle, the control board should be checked for error codes or signs of visible wear and tear that may indicate it needs to be replaced. Make sure that the dishwasher is turned off, unplugged, and completely disconnected from its power and water sources. It's recommended that work gloves are worn to prevent injury. This is a genuine OEM part and has been sourced directly from the manufacturer. This is an authentic part and as such is sold individually and made from durable, high-quality, non-corrosive materials to ensure the highest possible quality. This part is compatible with dishwashers that have been manufactured by Bosch, Thermador, Gaggenau, and various other brands.