She3ar76uc Parts

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

This hose clamp secures a rubber or plastic hose to its fitting inside the appliance, helping prevent leaks at connection points. Replace a stretched, corroded, or damaged clamp to maintain a tight, reliable seal.

• Clamps the hose to a barb or fitting to keep it from slipping off
• Helps maintain a watertight connection and reduce drips at the joint
• Can help resolve leaks caused by a loose hose connection
• Common signs: moisture around a hose joint, visible rust/deformation, or a clamp that won't tighten

• Disconnect power and turn off the water supply before servicing
• Place a towel or tray to catch residual water; note hose routing and clamp position
• Use appropriate hand tools for your clamp style; fully seat the hose and tighten evenly
• After reassembly, run a brief test and inspect for leaks at the connection

Replacement hood canopy that restores the vent cover and exterior appearance of your range hood. Installs in place of a dented, rusted, or damaged canopy to keep ventilation components protected and maintain a finished look. What it does:

• Covers and protects internal blower, controls and filters from grease, dust and damage
• Directs exhaust airflow through the hood; bent or crushed can disrupt ventilation
• Restores exterior appearance—visible dents, rust or corrosion are common signs it needs replacement
• Provides the proper mounting surface for filters and related hood components

• Disconnect power to the appliance before starting any repair
• Retain existing mounting hardware and seals unless new hardware is specifically listed as included

The CABLE HARNESS is an OEM part specifically designed for Bosch dishwashers. As the internal wiring backbone, it carries electrical signals operating all wash components according to cycles. 

Symptoms of a faulty cable harness include:

• Random component failures due to intermittent connections
• Repeated error codes relating to components not responding  
• Buzzing noises or excessive warmth around internal wires

Causes can be physical damage exposing wires, cracked wire insulation reducing conductivity over time, or broken connectors inhibiting communication. 

This replacement harness restores function and integrity to the sensitive electrical pathways within the dishwasher. Proper voltage transmission is crucial for wash arms, the pump, the heater, and control boards to seamlessly activate in sequence during cleaning.

Compatible with premium Thermador, Gaggenau, and Kenmore models using matching Bosch systems technology, this OEM harness precisely follows original conduit paths. 

Replacement housing that restores the appliance's outer enclosure and helps protect internal components from damage. Use this part when the original housing is cracked, broken or otherwise compromising appliance stability and appearance. What it does:

• Replaces a damaged outer housing to restore structural support and component protection.
• Helps reduce vibration and rattling caused by cracked or loose enclosure pieces.
• Prevents direct exposure of internal parts to dirt and moisture when intact.
• Improves the appliance's appearance by covering worn or broken bodywork.

• Disconnect power (and water supply if applicable) before beginning any repair.
• Remove control panels or trim as needed to access the housing; keep fasteners for reuse if undamaged.
• Handle edges carefully—metal or molded parts can be sharp.
• Verify part fit and orientation against the old housing before finalizing installation.

This cable supply is the factory replacement wire harness that delivers electrical power between components, restoring reliable connections and stable operation. Use it to replace damaged, frayed, or corroded supply wiring. What it does

• Provides the primary electrical connection between the appliance's power source and internal components.
• Restores continuity when the original cable is cut, burned, or shows visible wire damage.
• Helps stop intermittent power loss, control failures, or components that fail to start due to wiring faults.
• Maintains correct connector fit and routing to prevent shorting or chafing.

• One cable supply (wire harness) as shown.

• Always disconnect power (unplug appliance or switch off breaker) before inspecting or replacing wiring.
• Match connector shapes and wire colors to the original harness before installation; do not modify wires.
• Route the cable away from moving parts, sharp edges, and heat sources; secure with existing clips or fasteners.
• Clean or replace affected connectors to ensure a reliable connection.

This door pivot hinge secures and guides an appliance door so it opens and closes smoothly, helping maintain proper door alignment and sealing. It's a direct-fit replacement designed to restore stable door operation. What it does:

• Provides a pivot point to support the appliance door and maintain alignment
• Helps ensure the door closes fully to preserve internal temperature and performance
• Reduces door sag, rubbing, or misalignment that can cause uneven wear or gaps
• Can stop squeaks or binding caused by a worn or damaged hinge

• One hinge

• Disconnect power and empty the door area before starting; follow manufacturer safety instructions
• Support the door during removal and installation to prevent damage or injury
• Use existing fasteners unless replacements are specified by the manufacturer
• Tighten mounting hardware securely and check door alignment after installation

This insulating part restores the factory isolation and protection between components inside your appliance. Replacing a worn or missing insulator helps prevent damage from heat or contact so the unit operates safely as designed. What it does:

• Provides the specified insulation and spacing where installed
• Helps prevent heat transfer, shorting, or abrasion between adjacent parts
• Restores proper fit when the original insulator is cracked, deformed, or missing
• Common signs include discoloration, charring, brittleness, or the old piece crumbling/falling out

• 1 insulating part

• Disconnect power and allow the appliance to cool completely before service; shut off water or gas if applicable
• Note the original orientation and placement; take photos for reference
• Install without over-compressing; ensure it seats flat and does not interfere with nearby parts
• Reassemble, restore power, and test for normal operation

This suspension damper stabilizes the tub/drum by absorbing movement and vibration during operation. Replacing a worn damper helps reduce shaking and noise, improving spin performance and overall machine stability. What it does:

• Absorbs and controls tub/drum movement to reduce vibration and noise
• Helps prevent banging, "walking," or out-of-balance shutdowns during spin
• Can address excessive shaking, rattling, and longer spin times
• Restores smoother, more controlled operation when the original damper is worn

• One suspension damper

• Disconnect power and turn off water supply before servicing
• Access location varies by model; support the tub/drum to relieve load before removal
• Note orientation and reuse existing mounting hardware if new fasteners aren't provided
• After installation, re-level the appliance and run a test cycle to verify stability

This lock clamp is a small retaining clip that secures a component or connection inside the appliance. It keeps parts firmly seated and aligned to help prevent loosening, misalignment, or accidental disconnection during normal operation.

• Locks and retains the associated fitting or component in place
• Maintains a secure, correctly aligned connection
• Helps resist vibration-related movement during use
• If worn, broken, or missing, you may notice a loose connection, rattling, parts separating, or leaks at the joint

• Disconnect power; shut off water supply if the repair involves a water path
• Note the clip's orientation/position before removal (take a quick photo for reference)
• Use needle-nose pliers or a small flat-blade tool to release/install; avoid over-bending
• The component is fully seated and the clip is fully engaged before reassembly

This dishwasher cup shelf mounts to the upper rack to hold cups, mugs, stemware, and small items securely. Replace a broken or missing shelf to keep items upright and organized throughout the wash cycle.

• Provides a platform on the upper rack for cups, mugs, stemware, and small items
• Helps keep items upright and reduces movement during wash and rinse
• Restores proper loading when the original shelf is cracked, loose, or missing
• Common signs: broken mounting tabs, shelf won't stay in place, cups tipping over

• Unload the upper rack; removing the rack can make access easier
• Align the shelf's mounting tabs with the rack wires and snap firmly into place
• Confirm the shelf moves freely and does not interfere with the spray arm
• Test with a light load to ensure secure placement before full use