She4305uc-53 Parts

Small replacement O-ring that seals the dishwasher aqua sensor assembly to maintain a watertight seal and help ensure reliable sensor operation. Fits the sensor housing to reduce leaks and protect internal electronics. What it does:

• Seals the aqua/sensor housing to prevent water from escaping the sensor area
• Helps maintain accurate sensor readings by keeping the sensor dry and properly seated
• Commonly replaced when you see water pooling or dripping near the sensor assembly
• Used during aqua-sensor, pump, or housing repairs where the original seal is damaged

• Always disconnect power and turn off the water supply before starting repairs
• Replace the O-ring only when the sensor or housing is disassembled; inspect mating surfaces for damage or debris
• Ensure the O-ring is seated evenly in its groove before reassembly to avoid pinching or leaks

Replacement door hinge tension spring that restores proper door balance and smooth opening and closing on compatible Bosch appliances. Replaces a worn or broken door spring to help prevent sagging and doors that won't stay open. What it does:

• Provides counter-tension for the door hinge so the door stays level and moves smoothly.
• Restores proper balance to doors that feel heavy, sag, or close too quickly.
• Works as the return/tension element inside the hinge assembly to control door travel.
• Common repair for door sag, uneven closing, or doors that don't remain open.

• Disconnect power (or unplug) and remove water supply if working on dishwashers; follow all safety steps before servicing.
• Spring is under tension—wear eye protection and gloves; release or install slowly and carefully.
• May require removing the door panel or hinge caps.

This replacement control-panel button provides the physical interface to press the underlying switch on your appliance. Swap a cracked, missing, or sticky button to restore reliable actuation and a clean, finished look on the console.

• Interfaces with the control panel's switch to register button presses
• Allows selection of settings or power depending on its position
• Common symptoms: button loose, cracked, sticking, missing, or not engaging the switch
• Restores proper feel and alignment when the original is worn or damaged

• Disconnect power to the appliance before servicing
• Access the control console/fascia to reach the button location
• Remove the old button and seat the new button into the panel, aligning with the actuator
• Reassemble the console and test operation

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

This sump collects and channels dishwasher wash water into the wash pump, helping maintain proper drainage and reduce leaks at the tub-to-pump connection. Replace a cracked or damaged sump to restore correct water flow and sealing. What it does

• Directs wash water from the tub into the wash pump and drain system.
• Houses the pump inlet and seals the pump-to-tub interface.
• Prevents leaks by providing a secure seal between the tub and pump assembly.
• Common symptoms: pooling water in the tub, dishwasher not draining, leaks from the base, or unusual pump noise/vibration.

• Disconnect power and turn off the water supply before starting any repair.
• Handle carefully; inspect and replace any worn gaskets or seals when installing the new sump.
• Access typically requires removing lower access panels and the lower dish rack.
• After installation, test for leaks and proper drain operation before returning the appliance to normal use.

This is the right side hinge plate. For left side use 00298567.

The Button is an OEM part for Bosch dishwashers. This replacement button is essential for the proper operation of the dishwasher, allowing users to select various wash cycles and options. 

The need for replacement can arise from regular use, leading to wear and tear on the button mechanism, or accidental damage.

Symptoms of a failing Button include:

• Difficulty in engaging the desired dishwasher functions, which may result from a stuck or unresponsive button.
• Visible wear or damage to the button, affecting the aesthetic appeal and functionality of the dishwasher's control panel.
• The dishwasher failing to start a cycle or select specific settings, indicating that the button may not be activating the corresponding function properly.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This hose clamp secures a rubber or plastic hose to its fitting inside the appliance, helping prevent leaks at connection points. Replace a stretched, corroded, or damaged clamp to maintain a tight, reliable seal.

• Clamps the hose to a barb or fitting to keep it from slipping off
• Helps maintain a watertight connection and reduce drips at the joint
• Can help resolve leaks caused by a loose hose connection
• Common signs: moisture around a hose joint, visible rust/deformation, or a clamp that won't tighten

• Disconnect power and turn off the water supply before servicing
• Place a towel or tray to catch residual water; note hose routing and clamp position
• Use appropriate hand tools for your clamp style; fully seat the hose and tighten evenly
• After reassembly, run a brief test and inspect for leaks at the connection

Spring-style hose clamp that secures flexible water hoses to fittings on select appliances, helping maintain a leak-tight connection at hose joints. Keeps hoses seated to reduce leaks and ensure reliable water flow. What it does:

• Holds flexible inlet, drain, or circulation hoses tightly on barbed fittings and nipples.
• Prevents leaks and water loss at hose connections by maintaining steady clamp pressure.
• Common signs it needs replacement: dripping or pooling near hose connections, a loose or wobbly hose, or visible clamp corrosion or deformation.
• Small, inexpensive part that restores a secure hose connection when the original clamp has failed.

• Always disconnect power and shut off the water supply before servicing appliance plumbing.
• For spring-style clamps, use pliers to open the clamp, position it over the hose, and release slowly so it seats properly; ensure the hose is fully pushed onto the fitting.
• Inspect the hose and fitting for damage; replace the hose if cracked or excessively worn before installing a new clamp.
• Wear eye protection when compressing or releasing spring clamps to avoid injury from sudden release.

This genuine replacement holder is a support piece that secures its mating component inside the appliance. Replacing a cracked or missing holder restores proper positioning and helps prevent movement, noise, and premature wear during operation.

• Provides a stable mounting point and keeps the associated part properly aligned
• Helps reduce shifting, vibration, or rattling during use
• Common failure signs: cracks, breakage, loose fit, or a component that won't stay in place
• Restores secure support and reliable operation after damage or wear

• Disconnect power; also shut off water and allow hot surfaces to cool
• Note the original orientation and take photos to match during reassembly
• Transfer and reuse any original screws, clips, or bushings
• Tighten fasteners snugly without overtightening; verify alignment and test operation

The Control Unit is an OEM component specially designed for select Bosch dishwashers. As the appliance's main processor, it directs all wash cycles, temperatures, times, and auxiliary features.

Integrated circuitry executes complex programs with precision to thoroughly clean varied loads efficiently. Sensors monitor functions and provide cycle status updates to the control panel interface. 

Symptoms indicating control unit replacement include:

• Cycles failing to start or responding incorrectly to input selections  
• Error codes displayed without reason or resolution through reset
• Inoperative auxiliary settings like speed adjustment or half-loads 

Causes stem from degradation over decades of continuous thermal and electronic stresses. Water intrusions pose risks as circuit boards are fragile to short circuits.

This OEM Bosch replacement part is also compatible with Thermador, Gaggenau, and select Kenmore dishwashers utilizing identical cycles and diagnostics systems. Reinstallation ensures continued intended cycle performance.
 

This electrical control switch completes or interrupts the power circuit that runs a specific appliance function, restoring on/off control for responsive operation and safer use. What it does:

• Acts as the user-activated or circuit-activated on/off control for a discrete function
• Restores power flow when the switch is made, allowing the associated component or cycle to run
• Common symptom: appliance function won't start or respond when the control is pressed or activated
• Common symptom: intermittent operation or no power to a given feature

• One switch

• Disconnect power to the appliance before attempting any service to prevent shock
• Access and replacement steps vary by model; follow the appliance service manual or schematic for safe disassembly
• Handle connectors carefully and confirm secure wiring/terminal seating after installation

This outer door is the dishwasher's exterior front panel that restores the appliance's appearance and protects internal components from damage. It provides a finished look and replaces dented, scratched, or corroded panels. What it does

• Covers and protects the inner door assembly, controls, and insulation from impact and moisture.
• Restores the dishwasher's exterior finish and alignment for proper sealing.
• Helps prevent further cosmetic damage and exposure-related corrosion.
• Resolves issues where visible dents, deep scratches, or rust affect the door surface.

• One outer door panel only.

• Disconnect power and water supply before starting any repair.
• Door panels can be heavy or awkward—have a second person assist to avoid dropping or bending the panel.
• Follow the manufacturer's service manual for correct removal/reinstallation steps and torque specifications.
• If trim, latch, or control components are attached, verify whether they must be transferred from the old door.

Color: White.