She43p25uc Parts

This is the left side hinge plate. For right side use 00298570.

This door lock is the latch assembly that secures the dishwasher door and tells the control when the door is closed so cycles can start and run safely. It restores proper door closure and control interlock function. What it does:

• Secures the dishwasher door during operation to prevent accidental opening
• Engages the door-switch/sensor so the control will start and continue a cycle
• Prevents water from spilling by ensuring the door stays fully latched during wash
• Common symptom fix: dishwasher won't start or stops mid-cycle because the door won't lock

• One door lock / latch assembly as shown

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access typically requires removing the inner door panel; handle the door panel and wiring gently
• Test door operation and run a short cycle after installation to verify proper function

This sump clamp secures the dishwasher sump/drain assembly to the tub, keeping the seal and pump assembly held in place to prevent leaks and movement. It's a small but essential fastener for a watertight sump connection. What it does:

• Holds the sump/drain housing tightly against the tub to maintain a proper seal
• Prevents the sump assembly from shifting during operation, which can cause leaks or noise
• Helps stop water from leaking under the machine when the pump runs
• Supports proper alignment of the drain/pump components for reliable draining

• One sump clamp

• Disconnect power and water supply before starting any repair
• Access the sump area by removing the lower access panel or toe kick and tilting the machine as needed
• Inspect the sump seal/gasket and replace if cracked or damaged when replacing the clamp
• Tighten clip until secure but avoid forcing or deforming the sump housing; test for leaks after reassembly

This shaft for the float switch is the replacement shaft that secures and guides the dishwasher float to accurately detect water level, helping the appliance fill and shut off properly. Direct-fit design replaces the worn or broken float shaft. What it does

• Guides the float so the level-sensing switch can detect low or high water levels.
• Prevents overfilling by ensuring the float actuates the water-level switch reliably.
• Commonly replaces a cracked, bent or missing shaft that causes inconsistent fill, continuous filling, or water-level errors.

• One replacement float switch shaft.

• Disconnect power to the appliance before starting any repair.
• Remove the access panels and float assembly per your model's service instructions to reach the shaft.
• Inspect the float and switch for damage; replace only the failed components as needed.
• Reassemble carefully and test fill/stop operation before returning the appliance to service.

This spring-style hose clamp secures flexible appliance hoses to fittings, helping prevent leaks and loose connections. It's a small but critical fastener that keeps water and drain hoses sealed under normal operation. What it does:

• Holds a rubber or plastic hose firmly onto a barb or spigot to stop leaks
• Prevents hose slippage that can cause water pooling or drip symptoms
• Maintains a compressive seal that resists vibration and thermal cycling
• Commonly used on drain, fill, and circulation hoses in dishwashers and washers

• Disconnect power and shut off water supply before starting work
• Use appropriate pliers (hose clamp or needle-nose) to expand and position the clamp
• Ensure the clamp sits evenly over the hose barb and releases fully to secure the hose
• Inspect the hose and connection for damage; replace hoses if they are cracked or excessively worn

This replacement side panel restores the appliance's exterior finish and protects the cabinet edge from dings, scratches and wear. It's a direct-fit exterior trim piece that keeps the side of the unit looking finished and secure. What it does

• Covers and protects the appliance cabinet side from impact, scratches and cosmetic damage
• Restores a clean, factory appearance when original panel is dented, chipped or missing
• Helps maintain proper clearance and panel alignment with adjacent cabinetry
• Prevents exposed edges that can catch debris or snag clothing

• Includes: one side panel

• Disconnect power (and water supply if applicable) before starting work
• Handle panel carefully — edges may be sharp; gloves recommended
• Typically secured with screws or clips; retain hardware from the original panel or refer to the appliance parts diagram

The Float Assembly is an OEM part for Bosch dishwashers. This part prevents water from overfilling and potentially leaking onto the kitchen floor. The float triggers the switch to shut off the water inlet when the appropriate water level is reached, ensuring the dishwasher operates efficiently and safely.

Causes of a bad float assembly can vary from debris or buildup restricting the float's movement, damage to the float mechanism, or issues with the float switch itself.

Symptoms of a malfunctioning Float Assembly include:

• The dishwasher not filling with water properly
• Water overflowing from the dishwasher
• The dishwasher not starting due to the float being stuck in the "full" position

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Color: Black

The Panel-Facia is an OEM component specifically designed for select Bosch dishwashers featuring full-paneled front doors. It serves as the outer enclosure protecting internal electronics and circuitry.

Premium high-gloss surfaces endure years of moisture exposure without dulling. Thick reinforced polymers guard valuables against accidental bumps or bashes from nearby foot traffic.

Causes for replacement typically relate to direct impact fractures exposing delicate insides to potential liquid intrusion. Prolonged harsh chemical contact may also lead to stress cracks developing over time.

Symptoms requiring a new panel-facia include:

- Loose fasteners allowing unwanted side-side movement or door misalignment  
- Physical splits, punctures, or holes compromising the waterproof barrier
- Faded, scratched, or damaged finishes detracting from the modern aesthetic

This OEM Bosch replacement part is also compatible with Thermador, Gaggenau, and selected full-paneled Kenmore dishwashers maintaining consistent appearances. Reinstallation preserves protection and attractiveness.
 

The Door Latch is an OEM part for Bosch dishwashers. This latch mechanism securely fastens the dishwasher door in the closed position during operation.

Causes of a bad door latch can include wear and loosening of moving parts over time and cycles, or damage to latch components from forced or excessive door openings.

Symptoms of a bad door latch include:

• The door not closing or latching properly
• Unexpected door openings during the wash cycle
• Reduced safety with an unstable door

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This hose clamp secures a rubber or plastic hose to its fitting inside the appliance, helping prevent leaks at connection points. Replace a stretched, corroded, or damaged clamp to maintain a tight, reliable seal.

• Clamps the hose to a barb or fitting to keep it from slipping off
• Helps maintain a watertight connection and reduce drips at the joint
• Can help resolve leaks caused by a loose hose connection
• Common signs: moisture around a hose joint, visible rust/deformation, or a clamp that won't tighten

• Disconnect power and turn off the water supply before servicing
• Place a towel or tray to catch residual water; note hose routing and clamp position
• Use appropriate hand tools for your clamp style; fully seat the hose and tighten evenly
• After reassembly, run a brief test and inspect for leaks at the connection

This genuine replacement holder is a support piece that secures its mating component inside the appliance. Replacing a cracked or missing holder restores proper positioning and helps prevent movement, noise, and premature wear during operation.

• Provides a stable mounting point and keeps the associated part properly aligned
• Helps reduce shifting, vibration, or rattling during use
• Common failure signs: cracks, breakage, loose fit, or a component that won't stay in place
• Restores secure support and reliable operation after damage or wear

• Disconnect power; also shut off water and allow hot surfaces to cool
• Note the original orientation and take photos to match during reassembly
• Transfer and reuse any original screws, clips, or bushings
• Tighten fasteners snugly without overtightening; verify alignment and test operation