She53t55u Parts

This suspension damper stabilizes the tub/drum by absorbing movement and vibration during operation. Replacing a worn damper helps reduce shaking and noise, improving spin performance and overall machine stability. What it does:

• Absorbs and controls tub/drum movement to reduce vibration and noise
• Helps prevent banging, "walking," or out-of-balance shutdowns during spin
• Can address excessive shaking, rattling, and longer spin times
• Restores smoother, more controlled operation when the original damper is worn

• One suspension damper

• Disconnect power and turn off water supply before servicing
• Access location varies by model; support the tub/drum to relieve load before removal
• Note orientation and reuse existing mounting hardware if new fasteners aren't provided
• After installation, re-level the appliance and run a test cycle to verify stability

This overflow component directs excess water safely back into the dishwasher's water path to help prevent overfilling and leaks. Replace if damaged to restore correct water management and leak protection.

• Guides overflow water away from the tub into the proper return/drain path
• Helps maintain correct water level during fill
• Can address water collecting in the base pan or leaking from the lower front area
• Useful when the leak protection/float has been tripped or cycles stop due to a detected leak

• Disconnect power and turn off the water supply before servicing
• Access the overflow/water-channel area per your model's service procedure
• Note orientation and transfer any clips or seals from the old part if present
• Reassemble, restore power/water, and run a short cycle to check for leaks

This holder/retainer secures its mating part in the correct position inside the appliance, preventing unwanted movement and ensuring consistent operation. Replace a cracked or missing holder to restore a solid, factory fit and reliable performance.

• Supports and locks the attached component or rack/accessory in place
• Helps prevent vibration, rattling, or misalignment during use
• Typical signs of failure: broken tabs, visible cracks, looseness, or the part no longer staying secured
• Restores proper positioning of the related component for consistent function

• Disconnect power at the breaker; shut off water supply if applicable
• Note the holder's orientation; take a photo before removal
• Reuse existing screws/fasteners if none are supplied with the part
• Seat fully until it clicks/locks; do not overtighten into plastic

This is a replacement push button set for the control panel. It restores smooth, reliable button action so you can select settings without sticking or broken caps, keeping operation intuitive and the fascia looking clean.

• Replaces worn, cracked, or missing push button caps on the control interface
• Transfers your press to the underlying switch bank for proper function selection
• Helps resolve buttons that stick, wobble, or don't spring back
• Refreshes the appearance of the control panel

• Disconnect power to the appliance before servicing
• Remove or open the control panel to access the button set
• Note the position and orientation of each button; transfer components in the same order
• Before final reassembly, test each button for smooth travel and proper actuation

This facia panel is the exterior trim that covers a dishwasher's control console, restoring the appliance's appearance and protecting the underlying buttons and electronics from moisture and wear. It's a direct-replacement cosmetic and protective panel. What it does:

• Covers and protects the control console and electronic components from spills and moisture.
• Restores a damaged, cracked, or scratched front appearance for a cleaner finish.
• Keeps button and touchpad openings aligned for reliable user access.
• Helps prevent debris buildup behind the control area that can cause malfunctions.

• Disconnect power to the appliance before beginning any repair.
• Remove the outer door or control assembly per the appliance service instructions to access mounting screws or clips.
• Handle edges carefully to avoid scratching the replacement panel and to prevent cuts from metal edges.
• Reuse or replace any mounting screws/clips as needed; do not force panels into place.

This dishwasher cup shelf mounts to the upper rack to hold cups, mugs, stemware, and small items securely. Replace a broken or missing shelf to keep items upright and organized throughout the wash cycle.

• Provides a platform on the upper rack for cups, mugs, stemware, and small items
• Helps keep items upright and reduces movement during wash and rinse
• Restores proper loading when the original shelf is cracked, loose, or missing
• Common signs: broken mounting tabs, shelf won't stay in place, cups tipping over

• Unload the upper rack; removing the rack can make access easier
• Align the shelf's mounting tabs with the rack wires and snap firmly into place
• Confirm the shelf moves freely and does not interfere with the spray arm
• Test with a light load to ensure secure placement before full use

This insulating protection strip shields wiring and nearby components from heat and abrasion, helping maintain safe operation and prevent premature wear. It's a low-profile, heat-resistant sleeve used where wiring passes near hot appliance parts. What it does:

• Provides thermal and abrasion protection for wiring and small components
• Helps prevent shorting or insulation damage from heat exposure
• Reduces wear where wires contact sharp edges or moving parts
• Commonly used when replacing control or harness components near heat sources

• One insulating protection strip/sleeve as shown

• Only install with power disconnected and appliance fully cooled
• Position sleeve fully over exposed wiring or component and secure per OEM routing
• Inspect surrounding wiring and connectors for damage; replace any frayed insulation

This is a replacement screw used to secure panels, trim pieces, and small brackets on compatible Bosch appliances — a simple hardware fix that restores proper fit and stops rattling or loose parts. What it does:

• Fastens outer panels, control bezels, or internal brackets to the appliance chassis
• Keeps panels aligned so doors and controls fit and operate correctly
• Stops vibration noise caused by loose or missing fasteners
• Replaces damaged, stripped, or corroded screws

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Thread by hand to start, then snug; avoid over-tightening which can strip threads or crack panels
• If threads are damaged, replace the mating nut or threaded insert per OEM guidance

A replacement door hinge that restores smooth, stable door movement and proper alignment. Designed to replace the factory hinge so the appliance door opens, closes and stays aligned as intended. What it does:

• Supports and pivots the appliance door for normal opening and closing.
• Keeps the door aligned to prevent rubbing, gaps, or uneven sealing.
• Helps eliminate sagging or misaligned doors that make closing difficult.
• Works with original mounting points to maintain correct door motion.

• Use basic hand tools; for model-specific instructions.
• Disconnect power and/or gas and empty the appliance as required before servicing.
• Handle glass or insulated doors with care—use an assistant for heavy or awkward doors.

The Circulation Motor and Heater Assembly is an OEM part for Bosch dishwashers. This combined unit is responsible for circulating water throughout the dishwasher during wash cycles and heating the water to the optimal temperature for effective cleaning.

Causes of a bad circulation motor and heater assembly can include electrical failures, wear and tear over time, or damage from debris or mineral buildup. A malfunctioning assembly can result in poor cleaning performance and water not being heated correctly.

Symptoms of a bad circulation motor and heater assembly include:

• The dishwasher not cleaning dishes properly
• Water not heating to the required temperature
• Unusual noises such as grinding or humming during operation
• Error codes related to water circulation or heating

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Handle is an OEM part for Bosch dishwashers. It provides the surface for securely grasping and maneuvering the dishwasher door during opening and closing. 

Causes of a bad handle can include wear and tear from ongoing grasping motions. Repeated lifting and adjusting of the door places stress on handle components over time.

Symptoms of a bad handle include:

• Looseness, wobbling or detachment from the door assembly
• Sharp edges, cracks or splits compromising a firm grip
• Reduced ability to precisely guide the door into position

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter