She68t55uc Parts

This holder secures internal components to keep assemblies aligned and stable, reducing vibration and wear. It's a simple replacement that restores proper fit where a broken or missing clip causes loose panels or noisy operation. What it does

• Secures and aligns panels or wiring harnesses inside the appliance
• Prevents rattling, vibration, and misalignment caused by damaged or missing clips
• Helps maintain proper component spacing to avoid wear or interference
• Restores secure attachment after breakage or plastic fatigue

• Disconnect power and water before starting any repair
• Remove access panels or trim to reach the damaged clip—keep fasteners organized
• Press or snap the holder into place; replace any broken tabs before reassembling
• If plastic anchors are damaged, replace them with matching OEM clips

This electronic control board (control module programme) manages the appliance's cycle logic and user interface so the unit can run selected programs reliably. Replaces a faulty control for restoring normal cycle selection and operation. What it does:

• Interprets user commands and starts/stops cycles; corrects failures where the appliance is unresponsive to controls
• Controls timing, sensors, and actuator signals that enable proper wash/spin/dry sequences
• Common symptom fixes: appliance won't start, display errors or locked controls, cycles stop mid-run, or unresponsive buttons
• Works as the central PCB that communicates with other components (sensors, valves, motors)

• One control module programme (electronic control board)

• Disconnect power and water before beginning any repairs to avoid shock or injury
• Handle the board by edges and avoid static discharge; use ESD protection if available
• Reconnect all harnesses in their original positions; note connector locations before removal

This replacement hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal. Replacing a worn clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place for reliable operation.

• Applies clamping force to hold a hose on a barb or stub connection
• Helps prevent leaks at hose joints
• Common symptoms: water leaking at a hose connection, hose slipping off, poor fill or drain performance
• Replace when the original is loose, corroded, distorted, or lost tension; also recommended when installing a new hose

• Disconnect power and shut off water supply before servicing
• Expect some residual water; protect the work area
• Note the clamp's position/orientation; use appropriate hand tools for the clamp style
• Ensure the hose is fully seated and clamp is secure; run a test cycle and check for leaks

This insulating part installs in the specified location to help reduce heat transfer between internal spaces and exterior panels. Replacing a worn or missing insulator helps protect nearby components and maintain proper operating temperatures.

• Provides a thermal barrier to limit heat transfer to surrounding panels and wiring
• Helps prevent scorching or heat damage to adjacent components
• Restores proper insulation where the original has deteriorated or is missing
• Common signs of failure: visible damage or fraying, burnt odor, or unusually hot exterior areas

• Disconnect power and allow the appliance to cool completely before servicing
• Wear gloves and eye protection; insulation fibers can irritate skin and eyes
• Match the original orientation/placement; do not over-compress the material
• Keep insulation clear of vents, heating elements, fans, and moving parts

This suspension damper stabilizes the tub/drum by absorbing movement and vibration during operation. Replacing a worn damper helps reduce shaking and noise, improving spin performance and overall machine stability. What it does:

• Absorbs and controls tub/drum movement to reduce vibration and noise
• Helps prevent banging, "walking," or out-of-balance shutdowns during spin
• Can address excessive shaking, rattling, and longer spin times
• Restores smoother, more controlled operation when the original damper is worn

• One suspension damper

• Disconnect power and turn off water supply before servicing
• Access location varies by model; support the tub/drum to relieve load before removal
• Note orientation and reuse existing mounting hardware if new fasteners aren't provided
• After installation, re-level the appliance and run a test cycle to verify stability

This holder/retainer secures its mating part in the correct position inside the appliance, preventing unwanted movement and ensuring consistent operation. Replace a cracked or missing holder to restore a solid, factory fit and reliable performance.

• Supports and locks the attached component or rack/accessory in place
• Helps prevent vibration, rattling, or misalignment during use
• Typical signs of failure: broken tabs, visible cracks, looseness, or the part no longer staying secured
• Restores proper positioning of the related component for consistent function

• Disconnect power at the breaker; shut off water supply if applicable
• Note the holder's orientation; take a photo before removal
• Reuse existing screws/fasteners if none are supplied with the part
• Seat fully until it clicks/locks; do not overtighten into plastic

This insulating protection strip shields wiring and nearby components from heat and abrasion, helping maintain safe operation and prevent premature wear. It's a low-profile, heat-resistant sleeve used where wiring passes near hot appliance parts. What it does:

• Provides thermal and abrasion protection for wiring and small components
• Helps prevent shorting or insulation damage from heat exposure
• Reduces wear where wires contact sharp edges or moving parts
• Commonly used when replacing control or harness components near heat sources

• One insulating protection strip/sleeve as shown

• Only install with power disconnected and appliance fully cooled
• Position sleeve fully over exposed wiring or component and secure per OEM routing
• Inspect surrounding wiring and connectors for damage; replace any frayed insulation

This control module is the dishwasher's electronic programmer that manages wash cycles and user interface signals, restoring proper cycle control and status reporting when the original module fails. What it does:

• Replaces the dishwasher's main program/control board that runs cycle logic and timing.
• Helps resolve symptoms like no cycle start, unresponsive controls, or cycles stopping or not advancing.
• Restores communication between buttons/display and mechanical components when board-related faults occur.
• Does not include mechanical components; only addresses electronic/program control issues.

• Disconnect power at the breaker or unplug the appliance before starting; electric shock risk.
• Handle the board by edges and observe ESD precautions to avoid static damage.
• Installation typically requires removing the control panel and securing connectors; retain mounting hardware.

This is a replacement screw used to secure panels, trim pieces, and small brackets on compatible Bosch appliances — a simple hardware fix that restores proper fit and stops rattling or loose parts. What it does:

• Fastens outer panels, control bezels, or internal brackets to the appliance chassis
• Keeps panels aligned so doors and controls fit and operate correctly
• Stops vibration noise caused by loose or missing fasteners
• Replaces damaged, stripped, or corroded screws

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Thread by hand to start, then snug; avoid over-tightening which can strip threads or crack panels
• If threads are damaged, replace the mating nut or threaded insert per OEM guidance

A replacement door hinge that restores smooth, stable door movement and proper alignment. Designed to replace the factory hinge so the appliance door opens, closes and stays aligned as intended. What it does:

• Supports and pivots the appliance door for normal opening and closing.
• Keeps the door aligned to prevent rubbing, gaps, or uneven sealing.
• Helps eliminate sagging or misaligned doors that make closing difficult.
• Works with original mounting points to maintain correct door motion.

• Use basic hand tools; for model-specific instructions.
• Disconnect power and/or gas and empty the appliance as required before servicing.
• Handle glass or insulated doors with care—use an assistant for heavy or awkward doors.