Shem3ay55n/24 Parts

The operating module is the appliance's electronic control board for the user interface. It reads your control inputs and communicates with the main control so programs select and run predictably. Replace a failed module to restore consistent panel response.

• Processes control-panel inputs and manages cycle/program selection
• Communicates with the main control to execute start, pause, and option commands
• Drives control-panel indicators or display feedback
• Common failure symptoms include unresponsive buttons, no lights/beeps at the panel, intermittent inputs, or inability to start a cycle

• Disconnect power at the breaker before servicing
• Use ESD protection; handle the board by its edges
• Photograph connectors and transfer wiring one at a time to the same locations
• Ensure ribbon/plug connectors are fully seated and harnesses aren't pinched before restoring power

This insulating part restores the factory isolation and protection between components inside your appliance. Replacing a worn or missing insulator helps prevent damage from heat or contact so the unit operates safely as designed. What it does:

• Provides the specified insulation and spacing where installed
• Helps prevent heat transfer, shorting, or abrasion between adjacent parts
• Restores proper fit when the original insulator is cracked, deformed, or missing
• Common signs include discoloration, charring, brittleness, or the old piece crumbling/falling out

• 1 insulating part

• Disconnect power and allow the appliance to cool completely before service; shut off water or gas if applicable
• Note the original orientation and placement; take photos for reference
• Install without over-compressing; ensure it seats flat and does not interfere with nearby parts
• Reassemble, restore power, and test for normal operation

This suspension damper stabilizes the tub/drum by absorbing movement and vibration during operation. Replacing a worn damper helps reduce shaking and noise, improving spin performance and overall machine stability. What it does:

• Absorbs and controls tub/drum movement to reduce vibration and noise
• Helps prevent banging, "walking," or out-of-balance shutdowns during spin
• Can address excessive shaking, rattling, and longer spin times
• Restores smoother, more controlled operation when the original damper is worn

• One suspension damper

• Disconnect power and turn off water supply before servicing
• Access location varies by model; support the tub/drum to relieve load before removal
• Note orientation and reuse existing mounting hardware if new fasteners aren't provided
• After installation, re-level the appliance and run a test cycle to verify stability

A direct-replacement control panel push button that restores reliable press feedback and user control on compatible Bosch appliances. Easy cosmetic fix for a worn, cracked, or non-responsive button to make the appliance usable again. What it does

• Replaces a damaged or worn push button on the appliance control panel.
• Restores tactile feedback so selections register properly.
• Helps resolve symptoms like a stuck, loose, or visibly cracked button.
• Preserves the original panel appearance when replaced.

• Disconnect power to the appliance before beginning any work.
• Usually installs from the front of the control panel; some models require removing the console or trim first.
• Handle small plastic pieces carefully to avoid breakage; keep screws and clips organized.

This lock clamp is a small retaining clip that secures a component or connection inside the appliance. It keeps parts firmly seated and aligned to help prevent loosening, misalignment, or accidental disconnection during normal operation.

• Locks and retains the associated fitting or component in place
• Maintains a secure, correctly aligned connection
• Helps resist vibration-related movement during use
• If worn, broken, or missing, you may notice a loose connection, rattling, parts separating, or leaks at the joint

• Disconnect power; shut off water supply if the repair involves a water path
• Note the clip's orientation/position before removal (take a quick photo for reference)
• Use needle-nose pliers or a small flat-blade tool to release/install; avoid over-bending
• The component is fully seated and the clip is fully engaged before reassembly

This dishwasher cup shelf mounts to the upper rack to hold cups, mugs, stemware, and small items securely. Replace a broken or missing shelf to keep items upright and organized throughout the wash cycle.

• Provides a platform on the upper rack for cups, mugs, stemware, and small items
• Helps keep items upright and reduces movement during wash and rinse
• Restores proper loading when the original shelf is cracked, loose, or missing
• Common signs: broken mounting tabs, shelf won't stay in place, cups tipping over

• Unload the upper rack; removing the rack can make access easier
• Align the shelf's mounting tabs with the rack wires and snap firmly into place
• Confirm the shelf moves freely and does not interfere with the spray arm
• Test with a light load to ensure secure placement before full use

This is a single replacement mounting screw used to secure panels, trim, or components on compatible appliances. It restores proper fit and prevents parts from coming loose or vibrating during operation. What it does

• Secures panels, brackets, or components in place to maintain appliance alignment
• Stops rattling or vibration caused by loose fasteners
• Helps ensure switches, doors, or trims stay properly seated
• Replaces missing or stripped screws to restore original fit

• One replacement screw

• Use the correct driver and size; start threads by hand to avoid cross-threading
• Tighten securely but avoid over-torquing which can strip threads or crack plastic
• Disconnect power and follow appliance safety precautions when accessing internal parts

This lock clamp secures the appliance door latch assembly so the door closes and seals reliably. It replaces a worn or broken clamp to restore proper latch engagement and help prevent door misalignment or failure to stay closed. What it does

• Holds the door latch or interlock assembly in position so the door can securely close
• Helps restore normal door engagement when a loose or damaged clamp causes the door to sag or not latch
• Commonly replaced when the door makes noise, feels loose, or the latch does not align
• Works with the latch housing and nearby mounting hardware to keep the lock mechanism stable

• One lock clamp (single clamp only)

• High-level replacement: usually accessed from the door or control area; remove power before servicing
• Inspect adjacent latch, springs, and mounting screws and replace any damaged parts
• Tighten fasteners to secure the clamp without overtightening or deforming plastic parts

The Detergent Dispenser is an OEM replacement part for Bosch dishwashers. It is located inside the dishwasher and is responsible for properly delivering detergent at the appropriate time during wash cycles. The detergent dispenser has a compartment that holds detergent tablets or pods, and a mechanism that releases the correct amount to efficiently clean dishes.

Causes of a bad dispenser can include clogging or blockage in the dispenser mechanism, damage to the dispenser door or latch, or malfunctioning electronic components that control the dispensing process.

Symptoms of a bad detergent dispenser include:

• Detergent not dispensing or residue left in the dispenser
• Dirty dishes due to insufficient or improper detergent delivery
• Corrosion or buildup inside the dispenser area
• Dispenser door or cover cracked or damaged

This genuine Bosch OEM replacement part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Sump is an OEM part for Bosch dishwashers. It is located at the bottom of the dishwasher's tub, responsible for filtering and recirculating water during the wash cycle. The sump is designed to collect and filter out food particles and debris from the water, ensuring that only clean water is circulated throughout the dishwasher. It also houses the circulation pump, which propels the water through the spray arms to effectively clean your dishes.

A bad sump can occur due to clogs, damage, or wear and tear over time. Signs of a faulty sump include poor cleaning performance, water not draining properly, or unusual noises during operation.

Symptoms of a bad sump include:

• Food particles or residue left on dishes
• Water not draining properly 
• Unusual noises during operation

Replace your faulty dishwasher sump with this genuine OEM Bosch part to restore your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

The Button is an OEM part specifically designed for touch control interfaces on Bosch dishwashers. Comprising replacement buttons and membranes, it facilitates an intuitive selection of cycles and options. Working precisely behind lighted displays, the button kit provides customized care for every load.  

Symptoms of faulty buttons include:

• Failure to register inputs or select desired programs
• Stuck buttons refusing some commands altogether   
• Peeling or degradation diminishes legibility over time

Causes relate to general wear sustained through continuous use over many years. Minor spills or moisture seepage may also degrade adhesive bonding beneath plastic surfaces.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Pump Housing is an OEM part for Bosch dishwashers. It houses the circulating pump and motor assembly that circulates water throughout the dishwasher during all wash cycles. Located inside the dishwasher's sump, the pump housing plays a key role in water recirculation, pick-up, and distribution of water to spray arms for optimal cleaning performance.

Symptoms of a defective pump housing include: 

• Incomplete or weak water spray from arms
• Gaps in wash or rinse coverage 
• Soap residue or buildup clinging to dishes
• Sounds of grinding, rubbing, or vibration from the pump area

Causes of pump housing issues are often external damage or cracks incurred from impact or hard water mineral scale deposits built up over time. Replacing with this OEM housing restores peak water circulation for sparkling dishes.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

The Push Button Set is an OEM replacement part for Bosch dishwashers. It serves as the interface controlling various wash functions through programmed inputs. Responsiveness and reliability allow for convenient cycle selection.

Causes of a bad push button set can include normal wear from extensive use over time. Exposure to moisture penetration or residual cleaning chemicals could impact electronic components. 

Symptoms of a bad push button set include:

• Difficulty activating buttons fully to change settings  
• Functions that automatically reset or will not save selections  
• Lighted displays or indicators failing to illuminate controls
• Complete non-responsiveness requiring replacement of the set 

This Bosch OEM part ensures continued trouble-free programming of cycles to remove food soils. Compatible with select Thermador and Kenmore models, it maintains ease of use. Replacing a worn set prevents control malfunctions.

This insulating part cushions and thermally isolates internal components to help reduce heat transfer and vibration noise in the appliance. It's a small replacement piece that restores proper spacing and protection around sensitive parts. What it does:

• Provides thermal separation between hot components and surrounding cabinet parts to help prevent heat damage
• Cushions components to reduce vibration and rattling noises during operation
• Helps maintain correct part clearances for safe, reliable performance
• Used where original insulation was damaged, missing, or deteriorated

• Disconnect power and, if applicable, water before beginning any repair
• Handle carefully; avoid compressing or tearing the insulation during installation
• Verify correct orientation and secure fit against the intended component or cabinet surface