Shv4308uc/U12 Parts

Bushing included. To order bushing separately use 00165296. This is the right side hinge. For left side hinge use 00263115.

This is the left side hinge plate. For right side use 00298570.

This clamp secures a wooden or custom exterior panel to the appliance door, restoring proper panel alignment and reducing rattling or looseness. Designed to match the OEM bracket location and fit. What it does:

• Holds the decorative wood panel firmly against the dishwasher door frame
• Prevents the panel from shifting, sagging, or vibrating during cycles
• Restores even door fit and helps maintain the door's seal and appearance
• Works at the bracket attachment point to stabilize panel-to-door connection

• Disconnect power to the appliance before beginning any work
• Remove the outer door panel per the service manual to access the clamp location
• Inspect surrounding clips and screws; replace any damaged fasteners for a secure fit

This sump clamp secures the dishwasher sump/drain assembly to the tub, keeping the seal and pump assembly held in place to prevent leaks and movement. It's a small but essential fastener for a watertight sump connection. What it does:

• Holds the sump/drain housing tightly against the tub to maintain a proper seal
• Prevents the sump assembly from shifting during operation, which can cause leaks or noise
• Helps stop water from leaking under the machine when the pump runs
• Supports proper alignment of the drain/pump components for reliable draining

• One sump clamp

• Disconnect power and water supply before starting any repair
• Access the sump area by removing the lower access panel or toe kick and tilting the machine as needed
• Inspect the sump seal/gasket and replace if cracked or damaged when replacing the clamp
• Tighten clip until secure but avoid forcing or deforming the sump housing; test for leaks after reassembly

A reed switch door sensor that detects when the appliance door is closed so the control can start cycles. Replaces a failed magnetic sensor to restore reliable door-closed detection and normal operation. What it does

• Acts as a magnetic contact that signals the control when the door or lid is closed
• Helps prevent the appliance from starting if the door is open or not fully latched
• Common symptom fix for no-start, intermittent cycle start, or control not recognizing a closed door
• Works as the electrical switching element in the door/detector assembly

• One reed switch (single replacement sensor)

• Disconnect power to the appliance before replacing the part to avoid shock or damage
• Handle the switch and wiring gently; avoid bending or stressing terminals and solder joints
• Locate and access the door/detector area per your service manual or tech sheet; confirm connector orientation before installing

This shaft for the float switch is the replacement shaft that secures and guides the dishwasher float to accurately detect water level, helping the appliance fill and shut off properly. Direct-fit design replaces the worn or broken float shaft. What it does

• Guides the float so the level-sensing switch can detect low or high water levels.
• Prevents overfilling by ensuring the float actuates the water-level switch reliably.
• Commonly replaces a cracked, bent or missing shaft that causes inconsistent fill, continuous filling, or water-level errors.

• One replacement float switch shaft.

• Disconnect power to the appliance before starting any repair.
• Remove the access panels and float assembly per your model's service instructions to reach the shaft.
• Inspect the float and switch for damage; replace only the failed components as needed.
• Reassemble carefully and test fill/stop operation before returning the appliance to service.

This installation parts bag contains the small hardware needed to install and secure the dishwasher. It keeps required screws, clips and fasteners together so the unit mounts properly and operates quietly. What it does:

• Provides the mounting screws, clips and small fasteners used during dishwasher installation
• Secures the dishwasher to surrounding cabinetry or countertop to prevent shifting or vibration
• Replaces missing or lost installation hardware included with new units
• Helps ensure a complete installation when paired with the factory installation instructions

• Turn off power and water supply to the appliance before beginning installation.
• Follow the dishwasher installation instructions in the manufacturer service or user manual.
• Keep hardware organized and verify quantities against the manual before finishing installation.

This is the front corner block. For rear corner block use 00263093.

This replacement silverware basket holds forks, knives and spoons so utensils stay organized and clean during the dishwasher cycle. It restores a convenient, secure place for cutlery and helps prevent nesting for better wash coverage. What it does:

• Holds and separates silverware to improve cleaning and prevent items from nesting
• Provides a removable container that stays in place during wash cycles
• Fits into the lower rack to keep utensils contained and easy to unload
• Helps protect small items from falling to the tub or blocking the spray arm

• No tools typically required; slides or snaps into the lower rack location
• Remove all dishes and power off/dry area before installing to avoid injury
• Inspect rack tines and basket clips for damage; replace if broken to ensure proper fit