Shv58t53uc Parts

This replacement side panel restores the appliance's exterior finish and protects the cabinet edge from dings, scratches and wear. It's a direct-fit exterior trim piece that keeps the side of the unit looking finished and secure. What it does

• Covers and protects the appliance cabinet side from impact, scratches and cosmetic damage
• Restores a clean, factory appearance when original panel is dented, chipped or missing
• Helps maintain proper clearance and panel alignment with adjacent cabinetry
• Prevents exposed edges that can catch debris or snag clothing

• Includes: one side panel

• Disconnect power (and water supply if applicable) before starting work
• Handle panel carefully — edges may be sharp; gloves recommended
• Typically secured with screws or clips; retain hardware from the original panel or refer to the appliance parts diagram

This is the upper dishrack assembly for the dishwasher, which holds cups, glasses, and smaller items during the wash cycle. It includes the rack frame and may include tine rows and rollers that allow it to slide in and out of the dishwasher tub. Replace this assembly if the rack is rusted, has broken or bent tines, or if the rollers are damaged and no longer glide smoothly on the tracks.

Fix dishes not drying or cycles taking 3+ hours. This heating element heats wash water and enables drying. Moderate DIY repair with video guide.

Plastic cover that protects the drain pump mechanism from debris. Replace if cracked, broken, or tabs are bent preventing proper seal during drain cycles.

Detergent door won't close or stay shut? Replace the dispenser assembly. Takes about 20 minutes with basic tools—remove inner door panel and swap out.

This turbidity sensor detects how clear the dishwasher's wash water is so the control can adjust cycle time, rinses, and water changes. Replacing a faulty sensor helps restore proper cleaning performance and normal cycle lengths.

• Monitors soil level/clarity of the wash water
• Signals the control to extend or shorten wash and rinse phases as needed
• Helps optimize water use while maintaining cleaning results
• Failure symptoms can include unusually long or short cycles, poor cleaning, repeated draining/refilling, or cycles that won't advance

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher out as needed; access the sensor from the base area
• Place a towel to catch residual water; release the locking tab or twist-lock, unplug the connector, and install the new sensor fully seated and locked
• Restore power/water and run a test cycle; check for leaks

This upper trim strip finishes the top edge of the appliance's front opening, restoring a clean look and helping protect nearby components. Replace a cracked, missing, or loose strip to keep panels aligned and secure.

• Provides a finished edge along the upper portion of the door/face area
• Helps protect adjacent components from dust and minor splashes
• Maintains proper panel gaps and alignment
• Typical symptoms: visible cracks, warping, looseness, rattling, or exposed/sharp edges

• Disconnect power before servicing; also shut off water
• Remove the existing strip by releasing screws/clips; retain hardware for reuse
• Align the new strip and secure evenly—do not overtighten fasteners
• Check door/panel operation afterward to confirm proper fit and clearance

Dishwasher door won't stay closed or latch properly? This door latch securely fastens the door during wash cycles. Common DIY fix for door issues.

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

This is a trim strip that attaches along the lower portion of the dishwasher door. It helps seal the door edge and provides a finished appearance to the front panel. Replace this piece if it is cracked, warped, or missing, which can lead to water leaks around the bottom of the door during wash cycles.