Shv6803uc Parts

Drain hose clamp

Metal mounting bracket that secures the toe kick panel to the bottom of your dishwasher. Replace if bent, broken, or missing to properly attach panel.

Cotton sound-dampening pad installs under the dishwasher tub base. Replace if worn, torn, missing, or compressed to restore noise reduction.

Replacement water level control cover for dishwashers. Snaps over the water level control assembly. Order a new cover if yours is broken, cracked, or missing.

Replacement silverware basket holds and organizes forks, knives, and spoons in your dishwasher. Replaces cracked, broken, or missing cutlery holders.

Fix dishes not drying or cycles taking 3+ hours. This heating element heats wash water and enables drying. Moderate DIY repair with video guide.

The Cabinet Side Seals are an OEM part for Bosch dishwashers. These seals are located along the sides of the dishwasher cabinet and play a crucial role in preventing water leaks and maintaining an airtight seal during operation.

Causes of a bad seal can include general wear and tear over time, exposure to high temperatures or moisture, or damage from mishandling or improper installation.

Symptoms of a bad Cabinet Side Seal include:

• Water leaks or moisture buildup around the sides of the dishwasher
• Difficulty closing the dishwasher door properly
• Decreased efficiency in drying performance
• Potential for water damage to surrounding areas

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This turbidity sensor detects how clear the dishwasher's wash water is so the control can adjust cycle time, rinses, and water changes. Replacing a faulty sensor helps restore proper cleaning performance and normal cycle lengths.

• Monitors soil level/clarity of the wash water
• Signals the control to extend or shorten wash and rinse phases as needed
• Helps optimize water use while maintaining cleaning results
• Failure symptoms can include unusually long or short cycles, poor cleaning, repeated draining/refilling, or cycles that won't advance

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher out as needed; access the sensor from the base area
• Place a towel to catch residual water; release the locking tab or twist-lock, unplug the connector, and install the new sensor fully seated and locked
• Restore power/water and run a test cycle; check for leaks

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

Tall item spray head that attaches to the upper feed tube in your dishwasher. Replace if cracked, broken, missing, or won't lock into place properly.

Secures wooden or custom exterior panels to your dishwasher door. Replace if your panel rattles, shifts, or feels loose. Confirm fit with your model.

This is the cap that seals the rinse-aid dispenser reservoir on the inside of the dishwasher door. It threads or snaps into place to keep rinse aid contained until it is dispensed during the rinse cycle. Replace this cap if rinse aid leaks out prematurely, the cap is cracked or warped, or dishes are coming out spotted due to improper rinse-aid dispensing.

Spring-style hose clamp secures water and drain hoses to fittings, preventing leaks. Replace when connections loosen or clips lose tension. Confirm fit with your model number.

Secures the sump assembly to the tub, preventing leaks and movement. Replace if worn, cracked, or if you notice water leaking from the base of your dishwasher.

This is a tube-shaped actuator component used in the dishwasher's float switch assembly. It helps transmit the position of the float to the switch, which controls the water level inside the tub. Replace this part if the dishwasher is overfilling, not filling with water, or if the float mechanism feels loose or unresponsive.

Pump housing cover for dishwashers. Replaces cracked, broken, or missing covers that protect the pump assembly. Installs over the pump mechanism.