Shv68tl3uc Parts

This electronic operating module (programmer) controls a range of appliance functions and restores proper cycle selection and timing when the control board fails. Replaces a failed or unresponsive control module to help the appliance run intended cycles reliably. What it does:

• Manages cycle selection, timing, and user interface inputs on the appliance
• Receives commands from the control panel and operates relays/valves/motors accordingly
• Can correct symptoms like unresponsive controls, failure to start cycles, or erratic cycle behavior
• Resolves intermittent operation or incorrect cycle advancement when the original module is faulty

• One operating module (programmer)

• Disconnect power (unplug or shut off circuit breaker) before starting any work
• Handle the module carefully to avoid electrostatic damage; ground yourself before touching electronics
• Replacement may require reconnecting wiring harnesses and securing the module in its mounting; follow the appliance's service manual for exact procedure

This programmed control module manages an appliance's electronic commands and cycle sequencing so your machine runs the selected programs and responds to user inputs. It replaces the main control used to interpret settings and start cycles. What it does:

• Controls cycle selection, timing and program sequences for the appliance's operation
• Processes user commands from the touchpad/knobs and sends signals to valves, motors and heaters
• Can cause symptoms like unresponsive controls, failure to start cycles, or erratic program behavior when faulty
• May produce error codes or a blank/unresponsive display related to electronic control failure

• Disconnect power at the breaker before attempting service to avoid shock or damage
• Observe ESD precautions; control boards are sensitive to static — handle by the edges
• Verify connector seating and wire harness orientation during replacement

This replacement hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal. Replacing a worn clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place for reliable operation.

• Applies clamping force to hold a hose on a barb or stub connection
• Helps prevent leaks at hose joints
• Common symptoms: water leaking at a hose connection, hose slipping off, poor fill or drain performance
• Replace when the original is loose, corroded, distorted, or lost tension; also recommended when installing a new hose

• Disconnect power and shut off water supply before servicing
• Expect some residual water; protect the work area
• Note the clamp's position/orientation; use appropriate hand tools for the clamp style
• Ensure the hose is fully seated and clamp is secure; run a test cycle and check for leaks

This insulating part installs in the specified location to help reduce heat transfer between internal spaces and exterior panels. Replacing a worn or missing insulator helps protect nearby components and maintain proper operating temperatures.

• Provides a thermal barrier to limit heat transfer to surrounding panels and wiring
• Helps prevent scorching or heat damage to adjacent components
• Restores proper insulation where the original has deteriorated or is missing
• Common signs of failure: visible damage or fraying, burnt odor, or unusually hot exterior areas

• Disconnect power and allow the appliance to cool completely before servicing
• Wear gloves and eye protection; insulation fibers can irritate skin and eyes
• Match the original orientation/placement; do not over-compress the material
• Keep insulation clear of vents, heating elements, fans, and moving parts

This suspension damper stabilizes the tub/drum by absorbing movement and vibration during operation. Replacing a worn damper helps reduce shaking and noise, improving spin performance and overall machine stability. What it does:

• Absorbs and controls tub/drum movement to reduce vibration and noise
• Helps prevent banging, "walking," or out-of-balance shutdowns during spin
• Can address excessive shaking, rattling, and longer spin times
• Restores smoother, more controlled operation when the original damper is worn

• One suspension damper

• Disconnect power and turn off water supply before servicing
• Access location varies by model; support the tub/drum to relieve load before removal
• Note orientation and reuse existing mounting hardware if new fasteners aren't provided
• After installation, re-level the appliance and run a test cycle to verify stability

This overflow component directs excess water safely back into the dishwasher's water path to help prevent overfilling and leaks. Replace if damaged to restore correct water management and leak protection.

• Guides overflow water away from the tub into the proper return/drain path
• Helps maintain correct water level during fill
• Can address water collecting in the base pan or leaking from the lower front area
• Useful when the leak protection/float has been tripped or cycles stop due to a detected leak

• Disconnect power and turn off the water supply before servicing
• Access the overflow/water-channel area per your model's service procedure
• Note orientation and transfer any clips or seals from the old part if present
• Reassemble, restore power/water, and run a short cycle to check for leaks

This cable harness routes power and control signals between the appliance's control and its components. Replacing a damaged harness restores solid electrical connections so the unit starts, runs, and completes cycles without intermittent failures or non-working functions. What it does:

• Distributes electrical power and control signals between boards, motors, valves, and sensors
• Replaces wiring that is burnt, brittle, frayed, or corroded
• Helps resolve symptoms like won't start, intermittent operation, inoperative features, or error/fault indications related to open/shorted circuits
• Restores safe, reliable connectivity to prevent further electrical damage

• 1 cable harness assembly

• Disconnect power at the breaker or unplug the appliance before servicing
• Photograph/label connections and routing to match the original layout
• Seat connectors fully by the housings; do not pull on wires
• Route and secure away from sharp edges, moving parts, and hot surfaces to avoid chafing or heat damage

This holder/retainer secures its mating part in the correct position inside the appliance, preventing unwanted movement and ensuring consistent operation. Replace a cracked or missing holder to restore a solid, factory fit and reliable performance.

• Supports and locks the attached component or rack/accessory in place
• Helps prevent vibration, rattling, or misalignment during use
• Typical signs of failure: broken tabs, visible cracks, looseness, or the part no longer staying secured
• Restores proper positioning of the related component for consistent function

• Disconnect power at the breaker; shut off water supply if applicable
• Note the holder's orientation; take a photo before removal
• Reuse existing screws/fasteners if none are supplied with the part
• Seat fully until it clicks/locks; do not overtighten into plastic

This cable harness routes power and signals between appliance control and components to restore reliable electrical connections. It replaces a damaged or worn harness to help eliminate intermittent operation and connectivity issues. What it does:

• Replaces the main wiring harness that links controls, sensors, and motors for proper electrical communication
• Restores reliable power and signal paths to correct intermittent power, non-responsive controls, or components that won't run
• Ensures secure connector mating to prevent arcing and poor contact
• Matches OEM connector types and wire lengths to fit in the original routing

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock
• Compare the new harness to the old one for connector types and routing before installation
• Handle connectors by the housings; do not pull on wires. Ensure all plugs snap fully into place

This outer door panel replaces the exterior shell of a dishwasher door to restore appearance and protect internal components. It provides a clean, finished surface and helps maintain proper door alignment and sealing. What it does:

• Replaces a dented, scratched, or corroded exterior door surface to improve appliance appearance.
• Protects internal door components from damage and moisture exposure.
• Helps the door close and latch properly by restoring the correct outer panel alignment.
• Reduces drafts or gaps caused by a damaged outer shell that can affect door sealing.

• Disconnect power and shut off water before starting any repair.
• Keep track of all screws, clips, and insulation layers during disassembly for correct reassembly.
• Use appropriate tools and avoid bending the panel when aligning and fastening.

This insulating protection strip shields wiring and nearby components from heat and abrasion, helping maintain safe operation and prevent premature wear. It's a low-profile, heat-resistant sleeve used where wiring passes near hot appliance parts. What it does:

• Provides thermal and abrasion protection for wiring and small components
• Helps prevent shorting or insulation damage from heat exposure
• Reduces wear where wires contact sharp edges or moving parts
• Commonly used when replacing control or harness components near heat sources

• One insulating protection strip/sleeve as shown

• Only install with power disconnected and appliance fully cooled
• Position sleeve fully over exposed wiring or component and secure per OEM routing
• Inspect surrounding wiring and connectors for damage; replace any frayed insulation

This is a replacement screw used to secure panels, trim pieces, and small brackets on compatible Bosch appliances — a simple hardware fix that restores proper fit and stops rattling or loose parts. What it does:

• Fastens outer panels, control bezels, or internal brackets to the appliance chassis
• Keeps panels aligned so doors and controls fit and operate correctly
• Stops vibration noise caused by loose or missing fasteners
• Replaces damaged, stripped, or corroded screws

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Thread by hand to start, then snug; avoid over-tightening which can strip threads or crack panels
• If threads are damaged, replace the mating nut or threaded insert per OEM guidance