Shv99a15uc Parts

This retaining clip secures small appliance components in place to prevent movement and ensure reliable part alignment. It provides a simple, durable hold that keeps assemblies stable during normal use and service. What it does:

• Holds panels, covers, or wiring harnesses in position to prevent rubbing or disconnection
• Maintains alignment of moving or attached components to reduce noise and wear
• Helps prevent intermittent electrical or mechanical failures caused by loose parts
• Commonly replaced when broken, cracked, or missing after service or impact

• One retaining clip

• Basic hand tools may be required; inspect surrounding parts before reassembly
• Wear gloves and power off and unplug the appliance before servicing
• Replace only with the correct OEM-designated clip to ensure fit and function

This inner door is the interior panel for a dishwasher door that protects internal components and provides a finished inside surface. Replacing a damaged inner door restores proper sealing and appearance. What it does:

• Forms the interior surface of the dishwasher door and helps contain water during cycles
• Protects wiring, insulation, and electronics housed inside the door
• Helps maintain a proper seal to prevent leaks and improve wash performance
• Addresses symptoms like visible door damage, interior rust, dents, or moisture inside the door cavity

• Disconnect power and water supply before starting any repair
• Removing the outer door panel or control panel may be required;
• Keep fasteners and trim organized for reassembly; some clips or screws may be needed

This float switch lever is the actuator that moves the dishwasher's tub float to operate the water-level/flood-sensing switch, helping the appliance detect overfill and control fill/drain cycles. Replaces a worn or broken lever to restore proper float activation. What it does:

• Transfers movement from the tub float to the float switch so the machine senses water level correctly
• Commonly needed when a cracked or detached lever prevents the float from engaging the switch
• Can stop overfill-safety trips or no-fill symptoms caused by a non-responsive float assembly
• Works with the existing float and float switch; restores mechanical linkage function

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove lower access panels or tub components as required to reach the float assembly
• Inspect surrounding clips and the float for damage; replace any broken hardware
• Tighten securely but avoid over-torquing; test float movement and switch activation before reassembly

This condensation tube routes moisture from the dryer's vented condensate tank to the drain, helping prevent leaks and pooling under the appliance. It's a direct-replacement tank drain tube for compatible vented-tank models. What it does:

• Channels condensate away from the tank to the dryer drain connection to reduce water buildup.
• Helps stop leaking or pooling beneath the dryer when the tank is vented.
• Restores proper condensate flow if the original tube is cracked, clogged, or damaged.
• Compatible with vented-tank dryer assemblies that use a routed drain tube for condensate.

• Turn off and unplug the dryer before starting any repair; if applicable, shut off gas supply.
• Remove access panels as needed to reach the condensate tank and tube; avoid damaging nearby wiring or hoses.
• Ensure tube fittings seat fully and secure clamps or fasteners to prevent leaks.

This door handle replaces a worn or broken appliance door grip to restore a secure, comfortable surface for opening and closing. Designed to match the original fit and appearance for easy cosmetic repair. What it does:

• Provides a sturdy grip for opening and closing the appliance door
• Replaces cracked, loose, or cosmetically damaged handles
• Restores proper leverage to reduce stress on the door latch and hinges
• Helps improve the look of the appliance by replacing a worn handle

• One door handle

• Refer to your appliance model's service manual for step-by-step removal and installation instructions
• Installation typically requires basic hand tools; disconnect power (and water if applicable) before servicing
• Handle may attach with screws or snap-fit clips—keep removed fasteners for re-use unless replacements are provided

This rubber gasket seals appliance openings to help prevent water and air leaks and restore proper door/tub sealing. It replaces a worn or damaged seal to reduce leaking and maintain normal appliance performance. What it does

• Creates a watertight/airtight barrier between mating surfaces to prevent leaks.
• Helps maintain operating temperature and efficiency by sealing the door/tub.
• Common symptom: visible water around the door or base during use.
• Common symptom: cracked, flattened, or distorted seal material that no longer compresses.
• Works as a direct replacement for the matching OEM seal when damaged or worn.

• One gasket as shown on the product page.

• Turn off power and water supply to the appliance before starting any repair.
• Remove the old seal carefully, clean the mounting channel of debris and residue, and inspect the mating surface.
• Press the new gasket evenly into the channel, starting at one corner and working around to ensure full seating without twists.
• Test the door closure and run a short cycle to confirm there are no leaks; re-seat if necessary.

Drain hose clamp

This adjuster socket is the replacement socket used with a cabinet/appliance leveling foot to adjust and stabilize the unit. It lets you raise or lower the appliance for a level installation and steadier operation. What it does:

• Engages the appliance leveling foot so you can turn and set the height
• Restores proper leveling to reduce rocking, uneven doors, and drainage issues
• Provides a secure interface between the leg and adjustment tool or nut
• Durable replacement for worn or damaged socket components

• One adjuster socket

• Turn power off and unplug the appliance before accessing leveling components
• Access may require tipping or partially removing the front grill or toe panel per your model's service manual
• Verify correct socket orientation and thread engagement before lowering appliance back to floor

This M6 x 26 screw secures the dishwasher door tension/adjusting assembly so the door opens and closes smoothly. Replacement helps restore proper door alignment and reduces sagging, rattling, or uneven closing. What it does:

• Fastens the door tension/adjusting mechanism to the door assembly
• Maintains correct tension so the door stays level during use
• Helps stop door sag, uneven closing, or vibration noises related to a loose fastener

• Disconnect power and water supply before beginning any repair
• Use the correct M6 driver/socket and avoid stripping the head
• Thread the screw in straight and tighten until secure; do not overtighten

This insulating part is a small thermal insulator used to reduce heat transfer and protect nearby components in the appliance. It helps maintain proper internal temperatures and limits heat-related wear on surrounding parts. What it does

• Provides thermal separation between hot components and adjacent panels or wiring
• Helps reduce heat-related failure of nearby parts by slowing heat transfer
• Can reduce localized hot spots that cause odor or premature component wear
• Can help dampen minor vibration noise when fitted correctly

• Disconnect power to the appliance before accessing internal panels
• Remove outer panels or components as needed to reach the old insulating piece
• Handle gently; insulation materials can be fragile or have adhesive backing
• Reassemble panels securely and verify normal operation after installation