Shx57c02uc/48 Parts

Small replacement O-ring that seals the dishwasher aqua sensor assembly to maintain a watertight seal and help ensure reliable sensor operation. Fits the sensor housing to reduce leaks and protect internal electronics. What it does:

• Seals the aqua/sensor housing to prevent water from escaping the sensor area
• Helps maintain accurate sensor readings by keeping the sensor dry and properly seated
• Commonly replaced when you see water pooling or dripping near the sensor assembly
• Used during aqua-sensor, pump, or housing repairs where the original seal is damaged

• Always disconnect power and turn off the water supply before starting repairs
• Replace the O-ring only when the sensor or housing is disassembled; inspect mating surfaces for damage or debris
• Ensure the O-ring is seated evenly in its groove before reassembly to avoid pinching or leaks

This stainless-steel dishwasher door handle replaces a worn or damaged handle and restores a clean, flush grip on the front of the dishwasher door. It provides a durable, easy-to-grasp surface for everyday use. What it does:

• Replaces the exterior door handle so you can open and close the dishwasher smoothly; common symptom is a loose, cracked, or broken handle.
• Restores the appliance's appearance by matching stainless finishes.
• Provides a secure, comfortable grip for normal operation.
• Mounts to the door with factory fastening points.

• Always disconnect power to the appliance before servicing.
• Installation typically requires removing the inner door panel or access cover; keep track of mounting hardware.
• Use the correct hand tools and avoid overtightening fasteners to prevent damage.

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

This is the right side hinge plate. For left side use 00298567.

This electrical control switch completes or interrupts the power circuit that runs a specific appliance function, restoring on/off control for responsive operation and safer use. What it does:

• Acts as the user-activated or circuit-activated on/off control for a discrete function
• Restores power flow when the switch is made, allowing the associated component or cycle to run
• Common symptom: appliance function won't start or respond when the control is pressed or activated
• Common symptom: intermittent operation or no power to a given feature

• One switch

• Disconnect power to the appliance before attempting any service to prevent shock
• Access and replacement steps vary by model; follow the appliance service manual or schematic for safe disassembly
• Handle connectors carefully and confirm secure wiring/terminal seating after installation

This is the left side hinge plate. For right side use 00298570.

This sump clamp secures the dishwasher sump/drain assembly to the tub, keeping the seal and pump assembly held in place to prevent leaks and movement. It's a small but essential fastener for a watertight sump connection. What it does:

• Holds the sump/drain housing tightly against the tub to maintain a proper seal
• Prevents the sump assembly from shifting during operation, which can cause leaks or noise
• Helps stop water from leaking under the machine when the pump runs
• Supports proper alignment of the drain/pump components for reliable draining

• One sump clamp

• Disconnect power and water supply before starting any repair
• Access the sump area by removing the lower access panel or toe kick and tilting the machine as needed
• Inspect the sump seal/gasket and replace if cracked or damaged when replacing the clamp
• Tighten clip until secure but avoid forcing or deforming the sump housing; test for leaks after reassembly

This shaft for the float switch is the replacement shaft that secures and guides the dishwasher float to accurately detect water level, helping the appliance fill and shut off properly. Direct-fit design replaces the worn or broken float shaft. What it does

• Guides the float so the level-sensing switch can detect low or high water levels.
• Prevents overfilling by ensuring the float actuates the water-level switch reliably.
• Commonly replaces a cracked, bent or missing shaft that causes inconsistent fill, continuous filling, or water-level errors.

• One replacement float switch shaft.

• Disconnect power to the appliance before starting any repair.
• Remove the access panels and float assembly per your model's service instructions to reach the shaft.
• Inspect the float and switch for damage; replace only the failed components as needed.
• Reassemble carefully and test fill/stop operation before returning the appliance to service.

This front base sound insulation is a factory-style cotton pad that helps reduce dishwasher operating noise and provides thermal cushioning under the tub. It restores the appliance's original sound-dampening and insulation where worn or missing. What it does:

• Dampens vibration and reduces motor/tub noise heard during cycles
• Provides a thermal buffer under the dishwasher base to help maintain stable temperatures
• Helps prevent rattles and improves overall quiet operation when installed correctly
• Restores OEM-fit insulation performance after damage, wear, or removal

• One front base sound insulation pad (cotton), as shown

• Disconnect power and water supply before accessing the dishwasher base
• Remove the lower access panel and mounting hardware to reach the insulation area
• Install in the original location; use the same fasteners or adhesive method specified by the manufacturer

This holder secures a small appliance component in place to prevent movement and reduce noise and wear. It restores proper fit and helps keep connected lines and parts aligned for reliable operation. What it does

• Secures a hose, wire, or small assembly to the appliance frame to prevent rubbing or sagging
• Keeps components aligned to reduce vibration and rattling noises
• Helps maintain proper routing to avoid strain on connections
• Commonly replaced when loose, broken, or missing and causing movement or noise

• One holder

• Turn off power and, if applicable, water supply before starting work
• Inspect surrounding clips and fasteners; replace if damaged
• Install in the same orientation as the original; use proper fasteners if required