Shx9pt75uc Parts

This genuine bearing supports smooth, low-friction rotation of a moving component inside your appliance. Replacing a worn bearing restores quiet, consistent operation and helps protect the shaft and housing from accelerated wear.

• Provides radial support and alignment for a rotating shaft or arm
• Reduces friction to improve efficiency and minimize noise
• Helps prevent wobble and uneven wear on mating parts
• Typical signs of wear: grinding/squealing sounds, rough or seized rotation, excessive play

• Disconnect power and water supply and allow hot components to cool
• Access the assembly; note the original bearing's orientation and depth
• Inspect the shaft and housing; replace if grooved, bent, or heat-damaged
• Press the new bearing in squarely; avoid striking the inner/outer race and verify free rotation before reassembly

This is the appliance's main power on/off switch. It restores reliable control of electrical power to the unit so you can turn it on and off consistently.

• Controls AC power to the appliance's user interface and electronics
• Worn or stuck switch can cause no power, intermittent power, or inability to shut off
• Spongy or loose button feel may indicate internal switch failure

• Disconnect power before service to avoid electrical shock
• Access typically requires removing the control panel or console
• Note wire positions or take a photo before disconnecting
• Do not force tabs; transfer any clips or boots from the old switch if present

This suspension damper stabilizes the tub/drum by absorbing movement and vibration during operation. Replacing a worn damper helps reduce shaking and noise, improving spin performance and overall machine stability. What it does:

• Absorbs and controls tub/drum movement to reduce vibration and noise
• Helps prevent banging, "walking," or out-of-balance shutdowns during spin
• Can address excessive shaking, rattling, and longer spin times
• Restores smoother, more controlled operation when the original damper is worn

• One suspension damper

• Disconnect power and turn off water supply before servicing
• Access location varies by model; support the tub/drum to relieve load before removal
• Note orientation and reuse existing mounting hardware if new fasteners aren't provided
• After installation, re-level the appliance and run a test cycle to verify stability

This regeneration valve directs brine through your dishwasher's built-in water softener during recharge cycles, helping prevent hard-water film and spotting. Replacing a faulty valve restores consistent softening and better cleaning results.

• Opens to route salt brine through the ion-exchange resin during regeneration
• Helps maintain proper water hardness feeding the wash system
• Failure can lead to white film/spots, cloudy glassware, mineral buildup, and reduced cleaning
• Also contributes to inconsistent softener performance over time

• Disconnect power and turn off the water supply before servicing
• Access location varies by model; note hose routing and valve orientation during removal
• Inspect hoses and seals; replace if worn to prevent leaks
• Restore water/power and run a short cycle to check for leaks and proper operation

This water distributor routes wash water to the dishwasher's spray system, restoring proper circulation for thorough cleaning. It's a direct-replacement plumbing component used in compatible Bosch dishwasher models. What it does

• Directs incoming water to the spray arms and wash assembly for even distribution
• Helps restore normal spray pressure and coverage when the original distributor is damaged or clogged
• Works as the plumbing interface between the inlet/valve and internal wash components

• One water distributor

• Disconnect power and shut off the water supply before beginning service
• Handle plastic ports and mounting tabs carefully to avoid cracking; replace any worn seals or gaskets encountered
• Reassemble panels and test a short cycle to ensure proper water flow and no leaks

This small insert is a precision-fit piece that helps secure and align a mating component so it fits and functions properly. Replacing a worn or missing insert restores a solid connection and dependable operation. What it does:

• Provides a snug mounting/locating point for the related part
• Helps prevent looseness, rattling, or misalignment
• Restores proper fit after cracking, wear, or loss
• Common signs include a cracked or missing insert and parts that no longer stay in place

• 1 insert

• Disconnect power (and water supply, if applicable) before servicing
• Compare the new insert to your original to match and orientation
• Remove any broken fragments and clean the area before installation
• Press or snap into place carefully; do not force or overtighten any fasteners

This inlet seal is a small rubber gasket that creates a watertight connection at the dishwasher's water inlet. Replacing a worn seal helps stop leaks and ensures the inlet valve can fill the appliance properly. What it does:

• Seals the water inlet connection to prevent drips or steady leaks underneath the dishwasher
• Maintains a tight seal at the inlet valve so the fill cycle can operate normally
• Commonly replaced when there is visible wear, cracking, or persistent water on the floor
• Helps avoid water damage and the nuisance of repeated drainage or fill errors tied to leaking

• One inlet seal

• Turn off the water supply and disconnect power before servicing
• Remove the inlet valve or access panel as needed to reach the seal; replace with the old seal removed
• Make sure the new seal is seated evenly and the mating surfaces are clean before reassembly

This replacement rail restores smooth, supported movement of a dishwasher rack so loading and unloading work as intended. It replaces a worn, cracked, or bent rail to stop sagging and improve rack alignment. What it does:

• Guides the dishwasher rack along its track for consistent in-and-out motion
• Supports rack weight to prevent tipping or sagging when extended
• Replaces damaged, cracked, or worn rails that cause noisy or jerky operation
• Helps restore proper rack alignment and engagement with the rollers

• Disconnect power and turn off water supply before beginning any repair.
• Remove the affected rack to access and replace the rail; keep small clips or fasteners for reassembly.
• Inspect rack rollers and mounting clips; replace any damaged components for best performance.

This bottom case is the dishwasher base assembly that protects internal components and helps contain leaks, keeping the wash system stable and secure. It's a direct-fit replacement that restores the appliance's lower enclosure. What it does

• Forms the appliance's lower enclosure to shield the pump, motor and wiring from debris
• Helps direct and contain water in the event of minor leaks to protect surrounding components
• Provides mounting surfaces for lower hardware and supports correct alignment of internal parts
• Can reduce rattles or vibration caused by a damaged or cracked lower shell

• One bottom case

• Disconnect power and water supply before beginning any repair
• Handle the part carefully to avoid damaging edges, clips or mounting tabs
• Keep fasteners and any hardware from the original unit; verify fit and alignment before tightening
• If you see water or corrosion, dry and inspect surrounding components for damage before reassembly

This is a replacement electrical cable harness used to restore power or signal connections inside compatible appliances. It provides a direct, OEM-style connection for reliable operation and safer performance than damaged wiring. What it does:

• Replaces damaged or frayed wiring that can cause loss of power, intermittent operation, or control failures
• Restores proper electrical connections between components to prevent shorts or erratic behavior
• Helps eliminate issues like unresponsive controls, motors that won't run, or intermittent cycle problems
• Matches the OEM routing and connector style for correct fit and reliable contact

• Disconnect power before starting any repair to avoid shock or injury
• Inspect connectors and routing; replace any retainers or clips that are damaged
• Ensure connectors are fully seated and wires are routed away from moving parts and heat sources

This base panel is the lower kickplate that covers and protects the underside of the dishwasher, restoring the appliance's finished appearance and shielding internal components from dust and debris. It provides a simple cosmetic and protective repair. What it does:

• Covers the dishwasher's lower front area to protect base components and conceal internal parts
• Restores the appliance's original look when the kickplate is dented, cracked, or missing
• Helps reduce dust and debris entering the washer cavity and base assembly
• Stops drafts or light entry under the door when the original panel is damaged

• One base panel

• Remove power to the appliance before beginning work to avoid injury
• Typically secures with screws or clips at the base; keep fasteners from the original panel for reinstallation
• Handle carefully to avoid scratching the finish; alignment may require slight adjustment

This replacement frame restores the appliance's front cabinet trim for a clean, finished appearance and helps secure the control panel and door assembly. It's a direct-fit exterior trim piece designed to return proper alignment and protection. What it does

• Provides structural support and alignment for the front panel and control area
• Covers and protects internal edges from dirt, moisture, and impact
• Helps stop rattling or vibration caused by a warped or damaged trim
• Common symptom: visible damage, cracks, loose or misaligned front trim

• Remove power to the appliance before starting work to avoid electrical shock
• Small hand tools typically required; follow OEM disassembly sequence for access
• Handle trim carefully to avoid scratches; use a soft surface to rest parts
• If clips or screws appear damaged, replace them separately.