Shy66c05c Parts

The Door Latch is an OEM part for Bosch dishwashers. This latch mechanism securely fastens the dishwasher door in the closed position during operation.

Causes of a bad door latch can include wear and loosening of moving parts over time and cycles, or damage to latch components from forced or excessive door openings.

Symptoms of a bad door latch include:

• The door not closing or latching properly
• Unexpected door openings during the wash cycle
• Reduced safety with an unstable door

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This dishwasher door seal fits into the channel around the tub opening to create a tight, water-resistant barrier when the door closes. Replacing a worn seal helps stop leaks at the front of the unit and keeps cycles running efficiently. What it does:

• Forms a watertight perimeter seal between the tub and door
• Helps contain water and steam during wash and rinse cycles
• Aids proper door compression for reliable closing
• Common symptoms: water on the floor at the front, drips from door corners, visible cracks/flattening, or gaps in the gasket

• 1 door seal

• Disconnect power and turn off water supply before servicing
• Remove the old seal and clean the gasket channel thoroughly
• Start at the top center and press the new seal evenly into the groove without stretching
• Close the door to check for uniform compression, then run a short test cycle to inspect for leaks

This hinge cover is a molded trim piece that protects and conceals a refrigerator door hinge for a clean finished look. It helps keep hinge hardware free of dust and reduces sharp edges while restoring appearance. What it does

• Covers the door hinge area to hide hardware and improve the appliance's appearance
• Helps block dust and debris from accumulating on hinge components
• Reduces the risk of clothes or fingers catching on exposed hinge parts
• Matches OEM fit and shape to maintain proper clearance and alignment

• One hinge cover

• High-level replacement: remove the old cover and snap or screw the new cover into place (specific fasteners vary by model)
• Use basic hand tools if required; for model-specific instructions
• Disconnect power (or follow appliance-specific safety steps) before working near electrical components
• Inspect hinge and hardware while replacing the cover; replace damaged hinge components as needed

Bushing included. To order bushing separately use 00165296. This is the right side hinge. For left side hinge use 00263115.

A small spring-style hose clamp used to secure flexible appliance hoses to fittings and prevent leaks. Simple, durable replacement that restores a tight connection for water and drain lines. What it does:

• Compresses around a hose to hold it firmly on an inlet, outlet or drain fitting
• Helps stop leaks caused by loose or slipping hoses
• Keeps hoses seated during normal appliance operation and vibration
• Commonly used on dishwasher and washer drain or water hoses

• One hose clip / spring clamp

• Disconnect power and water supply before starting repairs
• Use pliers to expand the clamp for removal and reinstall; ensure hose is fully seated before releasing clamp
• Inspect the hose and fitting for damage; replace any cracked or brittle hose
• Do not overtighten or deform clamp when installing; replace if corroded or weakened

This retaining clip secures small appliance components in place to prevent movement and ensure reliable part alignment. It provides a simple, durable hold that keeps assemblies stable during normal use and service. What it does:

• Holds panels, covers, or wiring harnesses in position to prevent rubbing or disconnection
• Maintains alignment of moving or attached components to reduce noise and wear
• Helps prevent intermittent electrical or mechanical failures caused by loose parts
• Commonly replaced when broken, cracked, or missing after service or impact

• One retaining clip

• Basic hand tools may be required; inspect surrounding parts before reassembly
• Wear gloves and power off and unplug the appliance before servicing
• Replace only with the correct OEM-designated clip to ensure fit and function

This is the left hinge cap. For right hinge cap use 00165295.

This inner door is the interior panel for a dishwasher door that protects internal components and provides a finished inside surface. Replacing a damaged inner door restores proper sealing and appearance. What it does:

• Forms the interior surface of the dishwasher door and helps contain water during cycles
• Protects wiring, insulation, and electronics housed inside the door
• Helps maintain a proper seal to prevent leaks and improve wash performance
• Addresses symptoms like visible door damage, interior rust, dents, or moisture inside the door cavity

• Disconnect power and water supply before starting any repair
• Removing the outer door panel or control panel may be required;
• Keep fasteners and trim organized for reassembly; some clips or screws may be needed

This float switch lever is the actuator that moves the dishwasher's tub float to operate the water-level/flood-sensing switch, helping the appliance detect overfill and control fill/drain cycles. Replaces a worn or broken lever to restore proper float activation. What it does:

• Transfers movement from the tub float to the float switch so the machine senses water level correctly
• Commonly needed when a cracked or detached lever prevents the float from engaging the switch
• Can stop overfill-safety trips or no-fill symptoms caused by a non-responsive float assembly
• Works with the existing float and float switch; restores mechanical linkage function

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove lower access panels or tub components as required to reach the float assembly
• Inspect surrounding clips and the float for damage; replace any broken hardware
• Tighten securely but avoid over-torquing; test float movement and switch activation before reassembly

This condensation tube routes moisture from the dryer's vented condensate tank to the drain, helping prevent leaks and pooling under the appliance. It's a direct-replacement tank drain tube for compatible vented-tank models. What it does:

• Channels condensate away from the tank to the dryer drain connection to reduce water buildup.
• Helps stop leaking or pooling beneath the dryer when the tank is vented.
• Restores proper condensate flow if the original tube is cracked, clogged, or damaged.
• Compatible with vented-tank dryer assemblies that use a routed drain tube for condensate.

• Turn off and unplug the dryer before starting any repair; if applicable, shut off gas supply.
• Remove access panels as needed to reach the condensate tank and tube; avoid damaging nearby wiring or hoses.
• Ensure tube fittings seat fully and secure clamps or fasteners to prevent leaks.

This door handle replaces a worn or broken appliance door grip to restore a secure, comfortable surface for opening and closing. Designed to match the original fit and appearance for easy cosmetic repair. What it does:

• Provides a sturdy grip for opening and closing the appliance door
• Replaces cracked, loose, or cosmetically damaged handles
• Restores proper leverage to reduce stress on the door latch and hinges
• Helps improve the look of the appliance by replacing a worn handle

• One door handle

• Refer to your appliance model's service manual for step-by-step removal and installation instructions
• Installation typically requires basic hand tools; disconnect power (and water if applicable) before servicing
• Handle may attach with screws or snap-fit clips—keep removed fasteners for re-use unless replacements are provided

This rubber gasket seals appliance openings to help prevent water and air leaks and restore proper door/tub sealing. It replaces a worn or damaged seal to reduce leaking and maintain normal appliance performance. What it does

• Creates a watertight/airtight barrier between mating surfaces to prevent leaks.
• Helps maintain operating temperature and efficiency by sealing the door/tub.
• Common symptom: visible water around the door or base during use.
• Common symptom: cracked, flattened, or distorted seal material that no longer compresses.
• Works as a direct replacement for the matching OEM seal when damaged or worn.

• One gasket as shown on the product page.

• Turn off power and water supply to the appliance before starting any repair.
• Remove the old seal carefully, clean the mounting channel of debris and residue, and inspect the mating surface.
• Press the new gasket evenly into the channel, starting at one corner and working around to ensure full seating without twists.
• Test the door closure and run a short cycle to confirm there are no leaks; re-seat if necessary.

Drain hose clamp

This is the right hinge cap. For left hinge cap use 00165292.